亚、超音速机翼非定常广义气动力系数之间的关系

 <正> 研究弹性飞机的动力学特性应计及非定常广义气动力。为了尽可能保留非定常运动历程,应首先计算由阶跃函数形式下洗产生的非定常气动力函数(指示函数或指数函数),再利用卷积形式的迭加原理处理任意函数形式下洗产生的非定常气动力。用振型法建立飞机弹性运动方程,可将飞机上任一质点的弹性位移近似地表示为     

飞机V型外倾双垂尾载荷校准技术

根据垂尾载荷校准及建模需求,对飞机V型外倾双垂尾结构受载情况进行了分析和简化,确定了校准试验载荷,研制了垂尾载荷校准试验专用龙门梁架。采用液压协调加载技术,完成了外倾双垂尾载荷校准试验,建立了满足测载要求的载荷模型。此种方法充分利用了左右垂尾外倾、双垂尾之间空间较大的特点,对左右垂尾对称施加向外的单点、多点载荷,加载载荷侧向分量左右自平衡,垂向分量依靠飞机自身重量即可平衡,飞机不需要复杂的固定与约束。试验中采用先搭建龙门框架,再停放飞机的方法,降低了试验风险、加快了试验进度,取得了良好的试验结果,对其他此类结构的载荷校准具有一定的借鉴作用。     

The verification of GNSS tropospheric tomography model in a mountainous area

The GNSS (Global Navigation Satellite System) has not been developed as a meteorological data source provider, but with a careful and sophisticated processing strategy it might be used as one. The term GNSS tomography refers to the usage of the ray traced GNSS signal as scanning rays in the tomographic model input. The model is divided into a number of voxels. The system is inverted and value of refractivity is obtained. Typically, as in the most of the inverse processing, there is a problem of the undetermined system and as a consequence the cofactor matrix is close to singular. To avoid singularity additional conditions or constrains should be added to the system. Here, additional parameters are derived with the help of the air flow analysis in the Sudety mountains (south-west region of Poland), and special Slant Wet Delay (SWD) trimming procedure. The flow’s synthetic parameters like the Bruint-Väisälä frequency and the Froude number are determined. This way the type of the flow is recognized and the analysis of the impact of orographic barrier has been quantified. The SWDs from the GNSS observations were tested against, SWD from raytracing through the COAMPS model field. The modified GNSS tomography model was tested for the real GNSS observations delivered from the GNSS network Karkonosze located in the Sudety mountains and compared with the COAMPS model. The solution shows a considerable improvement in comparison with plain tomographic model results.     

三角翼DBD等离子体流动控制研究进展

现代战机采用较多的三角翼，在大迎角绕流时存在前缘涡破裂等气动问题。作为新型主动流动控制技术，等离子体激励频带宽、响应快、结构简单、便于闭环控制，在解决三角翼气动问题上具有潜力。回顾了介质阻挡放电（DBD）等离子体气动激励的基本原理，及其用于三角翼前缘涡控制的研究进展。从来流条件、几何构型、激励参数等方面分析了DBD等离子体激励对流动控制效果的影响规律；结合不同激励频率下流场演化特性，分析了流动控制机理。最后，从理论研究和工程应用的角度，对三角翼前缘涡控制的发展进行总结展望。     

飞机变形自动化测量方法研究

为解决以往飞机变形测量模式中人工干预较多,受测量环境影响较大,测量时间长等问题,基于Geo COM技术和RS232,在计算机与全站仪之间进行数据交换,设计了一套自动化测量系统。在测量过程中由标志点的机体理论坐标反算其在当前测站中的极坐标,从而在测量过程中驱动全站仪指向待测点,减少人工瞄准时间,并由计算机实时解算结果数据。经实际飞行试验验证表明,测量时间缩短为原来时间一半,大大提高了工作效率。     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

基于微型涡喷发动机热喷流的无源流体推力矢量喷管的控制规律

流体推力矢量喷管型面固定、活动部件少、结构重量轻，能够为高机动飞行器提供有效的飞行控制手段，但无源流体推力矢量喷管热喷流的偏转控制规律尚未完全掌握。为了推进无源流体推力矢量技术的实用化，本文设计研制了适用于微型涡喷发动机的耐高温喷管模型，对该喷管在微型涡喷发动机热喷流状态下的控制规律进行研究。利用非接触光学显示和测量手段——红外热成像拍摄和粒子图像测速（PIV）技术对主射流流动特性进行研究，获得流动矢量角随二次流控制阀门闭合度变化的控制规律；利用六分量盒式天平测力实验研究无源流体推力矢量喷管的力学特性，获得推力矢量角随二次流控制阀门闭合度变化的控制规律。研究结果表明：该构型喷管在微型涡喷发动机热喷流下主射流连续可控偏转，最大流动矢量角为-12.3°/12.3°，最大推力矢量角为-12.9°/12.8°，控制规律接近线性，不存在主射流偏转突跳问题。     

用测量法调节某型涡轮的轮背间隙

Cooling Turbine 204050是波音737飞机采用的一种涡轮冷却器,其传统的调节轮背间隙的方法操作繁琐、效率低下。本文介绍了一种测量法来调节204050的轮背间隙,该方法具有可靠性高、操作方便、效率高等优点。     

双向比对高精度物理时间同步方法

提出一种面向未来卫星在轨应用的闭环物理高精度时间同步方法。比较了所提方法与其他时间同步方法的区别与优势，建立了远程系统时间同步基本模型与误差传递模型，基于双向测距和时间传递技术分析了高精度钟差获取原理，给出了时钟调整环路的时域频域参数依赖关系。完成了高精度时间同步地面试验系统构建，测试了开环非调钟状态下钟差测量精度误差、闭环调钟状态下时间同步准确度误差以及长时运行情况下的时间同步监测结果。测试结果表明，该方法能够实现优于1 ns量级的时间同步，为高精度时间同步技术研究提供了新的途径。     

甲醇超临界水完全气化制氢系统的火用分析

基于热力学火用平衡方程所揭示的实际用能过程和理想用能过程,通过引入"偏离值"、"偏离度"两个指标,对甲醇超临界水制氢系统进行了火用分析。首先确定了加热和反应环节为重点优化环节;然后研究了此二环节的"偏离度"分别随压力、温度的变化规律,并比较了压力和温度对"偏离度"的影响作用大小。在提高甲醇制氢系统的能质利用率方面进行了有益的探讨,其结论对制氢系统的节能工作具有一定的参考价值。