基于数值分析的空速-动压信息处理方法

从数值计算方法的角度对大气数据校验系统设计中空速、指示空速与动压、静压转换关系进行研究,提出了一种新的转换方法。在PC计算机和ARM嵌入式计算机S3C2410上进行了模拟仿真,给出了计算程序和分析结果,与传统方法相比,具有转换速度快、程序简捷、精度高的特点,该方法用软件容易实现,可以很方便地应用到其它传感器的研究与设计中。     

减压直流非转移弧等离子体射流速度的静电探针测量

组建了一套利用静电探针诊断技术测量减压直流非转移弧等离子体射流速度的实验系统。对以纯氩为工质的等离子体,在气流量1．25×10^-1kg/s、弧电流80A、真空室压力165Pa的条件下,测量了射流的速度及其分布。结果表明射流在发生器出口处中心最高速度约为1200m／s,在半径20mm处减小到635m／s。沿射流轴线方向的速度梯度约为10（ms^-1）／mm。射流速度随着弧电流增加而缓慢单调增加;当真空室压力从165Pa提高到2kPa时,发生器出口轴线上的射流速度从1200m／s降至570m／s。     

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

The role of AVDR in linear cascade testing

Linear cascade testing plays an important role in the research and development of turbomachinery and is widely used over the world.The ideal cascade model of a turbomachinery blade row is two-dimensional.In actual linear cascade testing, the flow through the test section converges due to the development of the boundary layer and secondary flow along the sidewall surfaces of the test section.Axial velocity density ratio(AVDR) is adopted to account for the deviation of the tested cascade flow from the ideal 2D model.Among numerous published cascade works, the influence of AVDR on cascade performance is seen to be complicated with many affecting factors, such as those related to cascade/blade geometry and flow conditions.Also, controlling AVDR is limited by the facility capability.Furthermore, real blade-to-blade flow in turbomachines is usually associated with AVDR greater than unity due to limited span of blades between the hub and shroud such that cascade testing without reducing AVDR could be favored sometimes.All these facets add complexity and diversification to the matter.The current paper reviews previous studies and results on AVDR.Consolidated understanding on the role of AVDR and recommendations on how to deal with it in linear cascade testing are provided.      

喷雾器喷嘴出口喷流流场特性的实验研究

通过定性定量实验手段研究了以水为单介质流体的某农用喷雾器喷嘴出口流场。首先采用单反相机常规拍摄方法,记录了喷雾压力在50～4 000 Pa范围内的喷嘴出口流场,发现了随着喷雾压力增大,喷嘴出口射流的形状经历了形成液泡到液泡破裂的过程,以及射流发展及最终稳定过程。然后通过PIV测速技术对喷雾压力在1 000～4 000 Pa范围内的喷嘴出口流场进行了定量测量实验研究,获得了在纵向截面上,喷嘴出口速度随喷雾压力增大而增大,且在中心线上的速度随着离喷口距离的增加均呈现振荡衰减的变化规律。在同一位置横向截面上,随着喷雾压力的增加,旋流强度越强,流速越大;而在同一喷雾压力下,离喷嘴出口距离越近的横截面处旋流强度越大,流速也越大。本文实验研究结果验证了PIV测速技术可以用于水雾滴的速度场测量。     

GPS/INS组合系统空中对准方法研究

针对单天线的GPS与捷联惯性导航组合系统,提出了一种空中对准方案,不同于传统的传递对准方法,仅依靠GPS测量信息进行速度匹配,完成空中初始对准。该方案采用扩展卡尔曼滤波方法解决对准过程中的非线性问题。仿真结果表明该方案的对准精度(1σ)可以达到水平姿态误差0.07,°方位误差0.3°。     

复合材料层合板低速冲击损伤的预测模型

在低速冲击载荷作用下,建立了一种适用于铺层总数较多的复合材料层合板的损伤预测模型。采用三维Puck失效准则预测层内纤维与基体的破坏,并获得基体失效时的断裂面角度。根据低速冲击下复合材料层合板的层间分层损伤机理,同时考虑面内横向正应力、厚度方向正应力、层间剪应力和相邻铺层的损伤状态等因素对界面分层的影响,发展了一种新的冲击分层失效准则。为快速有效地预测铺层总数较多的复合材料层合板的冲击损伤,通过对单元积分点处的应变进行线性插值,提出了在单个实体单元内预测多个铺层损伤的数值计算方法。模型成功预测了受冲击层合板具体的失效模式,预测的分层形状和尺寸与试验值吻合较好,并显著减少了有限元模型的规模,表明本文所发展的数值方法对预测复合材料层合板低速冲击损伤的有效性。     

用PDA测量两相湍流流场时固体粒子的选择

激光法测量两相流是近年来开发的一项新技术，测量过程中需要存在合适的粒子。本文研究了用三维粒子动态分析仪（ＰＤＡ）测量气固两相湍流流场时固体粒子的选择问题。试验过程中，运用几种不同的粒子作为煤粉粒子的模拟粒子进行测量和比较，结果表明：（１）粒子的特性参数是影响测量精度的重要因素之一；（２）测最气固两相湍流流场中粒子的运动特征时，应尽可能选择形状较规则、折射率大、尺寸分布合理、不易粘结且易于收集同时接近所要模拟的粒子性能的固体粒子，必要的时侯应结合粒子性能对测量结果进行修正．     

改进的粒子群算法求解背包问题

本文提出了改进的粒子群算法求解背包问题,阐明了该算法求解背包问题的具体实现过程。通过与其他文献中实例的计算结果比较,表明该算法切实可行,有较高的搜索效率。     

高温射流中粒子测速的脉冲激光显微照像技术

为了获得高温射流中微粒的速度,建立了一套显微照像系统.该系统由双脉冲YAG激光光源、粒子放大成像系统、图像接收系统组成.在采用显微成像技术、补偿式滤光技术、序列成像技术后,克服了喷射粒子直径小、流场发光强、温度高等困难,实现了对同一粒子的两序列照像,根据两幅序列照片,获得了粒子的喷射速度.对该系统的组成、原理及试验结果进行了介绍.