A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

一种新型正弦压力发生器

介绍了一种利用压电叠堆激励管道内液体介质发生谐振产生正弦压力的发生装置.与其它正弦压力发生器相比,本装置压力源的激励方式新颖,工作频率较高,所产生的正弦压力波的幅值较大,失真度较小.     

Leakage performance of floating ring seal in cold/hot state for aero-engine

Rotating experimental investigations were carried out to study the oil sealing capability of two different floating ring seals in cold/hot state for aero-engine. High-speed Floating Ring Seal(HFRS) is a seal with the inner diameter of 83.72 mm and maximum speed of 38000 r/min, and Low-speed Floating Ring Seal(LFRS) is another seal with the inner diameter of 40.01 mm and maximum speed of 18000 r/min. In hot state, sealing air with the temperature of 371 K and oil with the temperature of 343 K was employed to model the working conditions of an aero-engine. Comparisons between floating ring seal and labyrinth seal were done to inspect the leakage performance.More attention was paid to the critical pressure ratio where the oil leakage began. Results show that the critical pressure ratio in cold state is obviously larger than that in hot state for both seals. An underlying sealing mechanism for floating ring seal is clarified by the fluid film, which closely associates with the dimensionless parameter of clearance over rotating diameter(2 c/Dr). Another fantastic phenomenon is that the leakage coefficient in hot state, not the leakage magnitude, is unexpectedly larger than that in cold state. Overall, the leakage performance of the floating ring seal is better than the labyrinth seal.     

Aerodynamic optimization design for high pressure turbines based on the adjoint approach

A first study on the continuous adjoint formulation for aerodynamic optimization design of high pressure turbines based on S2surface governed by the Euler equations with source terms is presented.The objective function is defined as an integral function along the boundaries,and the adjoint equations and the boundary conditions are derived by introducing the adjoint variable vectors.The gradient expression of the objective function then includes only the terms related to physical shape variations.The numerical solution of the adjoint equation is conducted by a finitedifference method with the Jameson spatial scheme employing the first and the third order dissipative fluxes.A gradient-based aerodynamic optimization system is established by integrating the blade stagger angles,the stacking lines and the passage perturbation parameterization with the quasi-Newton method of Broyden–Fletcher–Goldfarb–Shanno(BFGS).The application of the continuous adjoint method is validated through a single stage high pressure turbine optimization case.The adiabatic efficiency increases from 0.8875 to 0.8931,whilst the mass flow rate and the pressure ratio remain almost unchanged.The optimization design is shown to reduce the passage vortex loss as well as the mixing loss due to the cooling air injection.     

载人航天器空气环境参数控制非定常仿真分析

为支持乘员在轨驻留,载人航天器需通过空气环境控制系统将众多设计参数和空气环境参数控制在指标范围内。文章建立了一种载人航天器空气环境非定常控制仿真分析模型,包括舱体模块、航天员模块、舱压控制模块、温湿度控制模块以及CO2净化模块。利用该模型分析了载人航天器空气环境参数随乘员代谢水平的非定常变化趋势,并评估了控制系统的工作性能。结果表明:乘员代谢水平变化对空气环境参数有显著影响,通过调节控制系统运行参数可将各空气参数控制在有效指标范围内。人区温度与O2分压、CO2分压和人区湿度有密切的影响关系,不可孤立地进行分析。为载人航天器空气环境参数控制系统的设计和流程改进提供了依据。     

A closed-form solution for moving source localization using LBI changing rate of phase difference only

Due to the deficiencies in the conventional multiple-receiver localization systems based on direction of arrival(DOA) such as system complexity of interferometer or array and amplitude/phase unbalance between multiple receiving channels and constraint on antenna configuration,a new radiated source localization method using the changing rate of phase difference(CRPD)measured by a long baseline interferometer(LBI) only is studied. To solve the strictly nonlinear problem, a two-stage closed-form solution is proposed. In the first stage, the DOA and its changing rate are estimated from the CRPD of each observer by the pseudolinear least square(PLS) method,and then in the second stage, the source position and velocity are found by another PLS minimization. The bias of the algorithm caused by the correlation between the measurement matrix and the noise in the second stage is analyzed. To reduce this bias, an instrumental variable(IV) method is derived. A weighted IV estimator is given in order to reduce the estimation variance. The proposed method does not need any initial guess and the computation is small. The Cramer–Rao lower bound(CRLB) and mean square error(MSE) are also analyzed. Simulation results show that the proposed method can be close to the CRLB with moderate Gaussian measurement noise.     

弹射筒内筒组件钢球收压及检测工艺

本文对航空火箭弹射座椅弹射筒内筒钢球收压技术要求、难点进行了工艺分析;介绍了钢球收压工艺技术难点、检测方法及注意事项等,在工艺技术研究及设计过程中取得了一定的技术积累,具有良好的借鉴、推广应用意义。     

椭圆形切扇修形对波瓣混合器掺混性能影响

在保证面积不变的情况下,选取不同的长轴、短轴,对波瓣混合器进行椭圆形切扇修形,研究切口深度与宽度对波瓣混合器掺混性能的影响规律。使用商用 CFD 软件对流场进行数值模拟。结果显示,对波瓣侧壁进行切扇处理会加强流向涡的强度,切扇越深,流向涡强度越大;切扇波瓣流向涡的耗散速率要大于基准波瓣混合器的流向涡耗散速率,预示着更为高效的掺混;引射系数与切口深度成正比,而总压恢复系数与切口深度成反比。考察了两种衡量热混合效率的模型并对其信度进行了比较,发现在 x =0.4 m 之前切扇可以提高热混合效率,而在 x =0.4 m 之后,基准波瓣混合器热混合效率要大于切扇波瓣混合器。     

利用格壁安装角对栅格舵展开折叠压心控制的工程方法研究探索

随着技术的发展，在工程设计中，对于巡航迎角下栅格舵导弹的展开与折叠的压心变化控制对于控制系统来说尤为重要。本文创新性的首次提出利用栅格舵的内壁单元的偏转，即相对于水平面的夹角来实现在设计点下的压心控制。由于设计过程需要多次迭代，本文利用计算在所关注的设计点处对展开折叠压心进行了验证，创造性的利用了等效代替的方法提出了一种新型的计算折叠状态压心的快速工程方法。