飞机典型结构细节——紧固孔随机裂纹扩展分析

根据7475T761铝合金犬骨型试样在随机谱载荷作用下的试验结果,采用两种随机裂纹扩展分析的方法,即通用的和解析的分析方法,研究了飞机典型结构细节——紧固孔中疲劳裂纹扩展的概率累积损伤,给出了概率裂纹扩展轨迹、裂纹扩展损伤累积分布及裂纹超出数的概率。试验结果与预测结果的比较表明,两者十分吻合,能满足工程精度的要求,为飞机结构的耐久性和损伤容限评估提供了适用的分析手段。     

疲劳裂纹扩展速率统计分析

给出了4种常幅载荷下疲劳裂纹扩展速率的统计处理方法,获得了在规定存活率P下的“P-da/dN-△K”关系,并对LC9中心裂纹试样试验数据进行了统计分析,给出了存活率为0.50、0.90、0.95和0.99时Paris方程中的c和n值。最后对4种方法进行了比较。     

TC17 合金焊接接头显微组织与疲劳裂纹扩展特性

研究了TC17钛合金惯性摩擦焊焊接接头的疲劳裂纹扩展规律,并利用光学显微镜、扫描电镜对材料的显微组织和断口形貌进行分析。结果表明:TC17钛合金母材为α+β网篮状组织,晶粒较大;焊缝区和热影响区内可以看到明显的原β相晶界,焊缝区的原β晶粒较细小,热影响区的原β晶粒较粗大,晶粒内部存在细小的α相。在室温下,当ΔK≤15 MPa.m1/2时,焊缝区疲劳裂纹扩展速率较小,而当ΔK≥15 MPa.m1/2时,焊缝区的扩展速率最大,其次是热影响区,母材的裂纹扩展速率最小;在高温下,焊接接头各部位的裂纹扩展速率相差不大,均小于室温。     

整体壁板三维裂纹应力强度因子计算与分析

近年来,整体壁板成为飞机结构设计上一个新的研究方向。针对典型的飞机整体壁板,应用有限元软件ABAQUS建立了含裂纹整体壁板的参数化模型,对裂纹在凸台和筋条中的扩展轨迹进行三维裂纹扩展模拟。分析了裂纹在扩展过程中,凸台、筋条、蒙皮中裂纹应力强度因子的变化情况以及凸台、筋条的止裂性能。研究结果对整体壁板的损伤容限设计和评定具有一定的指导意义。     

基于狄氏先验分布的固体火箭发动机可靠性增长Bayes分析

针对固体火箭发动机研制存在历史信息和专家信息的特点,提出了一种可靠性增长分析的Bayes模型。以狄氏分布作为先验分布,给出了先验分布参数的确定方法。综合利用了先验信息和每一阶段现场试验信息,推导了各阶段可靠性的后验边际分布。给出了当前阶段和后续阶段产品可靠性的Bayes点估计和置信下限,分析了各阶段试验结果对最终产品可靠性估计的影响。最后给出了一个实例,验证了该模型的有效性。     

基于及时修正策略可靠性增长的动态Bayes评估方法

针对指数寿命型设备在及时修正策略下的可靠性增长过程,提出了一种动态Bayes评估方法。该方法建立了及时修正策略下的AMSAA模型,并依据已有研制试验数据,对下一次试验的设备失效率进行预测,并将预测结果作为对新技术状态下设备失效率的验前认识,然后利用最大熵方法给出设备失效率的验前分布,进而实现对产品可靠性增长的Bayes统计分析。最后给出了该方法的具体算例,通过对比分析证明了该方法的有效性。     

新疆高等教育发展与经济增长关系的协整分析

文章利用新疆1980-2010年数据，对高等教育发展与经济增长之间的关系进行研究，建立协整方程和误差修正模型，进行了格兰杰因果关系检验，得出的主要结论是：新疆经济增长和高等教育规模之间存在长期的协整关系；且经济增长对高等教育规模是单向格兰杰因果关系。在此分析的基础上，提出新疆高等教育与经济可持续发展的对策建议。     

Fatigue crack propagation of new aluminum lithium alloy bonded with titanium alloy strap

A new type of aluminum lithium alloy (Al-Li alloy) Al-Li-S-4 was investigated by test in this paper. Alloy plate of 400 mm · 140 mm · 6 mm with single edge notch was made into samples bonded with Ti-6Al-4V alloy (Ti alloy) strap by FM 94 film adhesive after the surface was treated. Fatigue crack growth of samples was investigated under cyclic loading with stress ratio (R) of 0.1 and load amplitude constant. The results show that Al-Li alloy plate bonded with Ti alloy strap could retard fatigue crack propagation. Retardation effect is related with width and thickness of strap. Flaws have an observable effect on crack propagation direction.     

Development of an improved ground-based prototype of space plant-growing facility

Based on a formerly developed ground-based prototype of space plant-growing facility, the development of its improved prototype has been finished, so as to make its operating principle better adapt to the space microgravity environment. According to the developing experience of its first generation prototype and detailed demonstration and design of technique plan, its blueprint design and machining of related components, whole facility installment, debugging and trial operations were all done gradually. Its growing chamber contains a volume of about 0.5 m³ and a growing area of approximate 0.5 m²; the atmospheric environmental parameters in the growing chamber and water content in the growing media were controlled totally and effectively; lighting source is a combination of both red and blue light emitting diodes (LED). The following demonstrating results showed that the entire system design of the prototype is reasonable and its operating principle can nearly meet the requirements of space microgravity environment. Therefore, our plant-growing technique in space was advanced further, which laid an important foundation for next development of the space plant-growing facility and plant-cultivating experimental research in space microgravity condition.     

Assessing the feasibility of involving gaseous products resulting from physicochemical oxidation of human liquid and solid wastes in the cycling of a bio-technical life support system

The study addresses the possible ways of involving gaseous products produced by “wet” incineration of human wastes mixed with H₂O₂ in an alternating electric field in the cycling of the physical model of a bio-technical life support system (BTLSS). The resulting gas mixture contains CO₂ and O₂, which are easily involved in the cycling in the closed ecosystem, and NH₃, which is unacceptable in the atmosphere of the BTLSS. NH₃ fixation has been proposed, which is followed by nitrification and involvement of the resulting products in the mass exchange of the closed system. Experiments have been performed to show that plants can be grown in the atmosphere resulting from the closing of the gas loop that includes a physicochemical installation and a growth chamber with plants representing the phototrophic compartment of the BTLSS. The results of the study suggest the conclusion that the proposed method of organic waste oxidation can be a useful tool in creating a physical model of a closed-loop integrated BTLSS.