基于摄动理论的爆高确定方法研究

分别讨论了两种通过飞行时间确定爆高的方法:解析计算修正法和时间偏导数法,这两种方法都是通过计算延迟时间来确定爆高,具有自主性强、可靠性高的特点。计算了两种方法在不同干扰条件下的结果,分析了造成计算偏差的原因。计算结果表明,两种方法的计算误差都非常小,均可应用于弹道导弹爆高确定。     

基于虚拟仪器的切削力监控技术研究

研制了一种基于虚拟仪器界面、供现场使用的高精度、高效率的金属切削过程监控系统。研究中采用回归分析、叠加原理及抛物线插值的方法建立切削力模型 ,并基于该模型进行参数估计来提取切削状态特征 ,进而监控整个切削过程     

铝合金T型材拉弯成形的有限元模拟

针对目前拉弯成形中的问题,采用有限元模拟的方法,对带下陷拉弯过程进行计算机仿真,得到优化后的工艺参数,避免了盲目的试拉,提高了加工效率,降低了拉弯成本,积累了带下陷拉弯成形的经验,提高了公司拉弯工艺水平。     

基于卫星观测数据的弹道导弹初始状态估计

利用卫星探测数据对大气层外飞行的弹道导弹弹道进行估计。在极大似然估计中,由于卫星探测导弹运动的可观测性较差,使初始点估计变得十分病态,传统的Gauss Newton迭代算法不再适用,而采用较为复杂Levenberg Marquardt算法,分别对单颗卫星和两颗卫星的情况进行了Monte Carlo仿真,得到了各自的归一化残差测量误差(代价函数),结果表明该算法有效。     

GPS/INS超紧组合载波跟踪环路最优带宽在线设计

在全球定位系统和惯性导航系统组成的超紧耦合系统中,卫星信号的跟踪性能直接取决于载波跟踪环路的带宽。为提高最优带宽的计算精度,在对惯导辅助下载波跟踪环路跟踪特性进行分析的基础上,详细推导了载波多普勒频率估计误差、多普勒频率变化率估计误差的计算方式,建立了惯导辅助下的环路跟踪误差模型;在实时估计跟踪载噪比的基础上,应用离散牛顿二阶梯度法迭代解算最优带宽,并进行实时调整。仿真结果表明,所设计最优带宽迭代解算方法的计算精度能够在11次迭代内达到99.6%,以此作为环路的带宽,能够在弱信号、辅助信息精度较低的情况下有效提高环路的跟踪精度。     

基于星体边缘和轨道投影的光学自主导航算法

针对光学导航中存在的通过星体（球体）图像部分边缘点拟合椭圆参数计算轨道参数产生中间误差的问题,提出利用边缘点映射轨道参数的直接投影模型,避免拟合椭圆参数的方法。在小孔成像模型基础上,建立了边缘点与轨道参数的直接投影数学模型,对其映射过程进行了理论推导,利用列文伯格-马夸尔特迭代算法进行求解轨道参数。用实际探测器以及镜头参数进行数值仿真验证,结果表明：该方法在相同边缘点的条件下,轨道精度可以达到5‰。与传统方法相比,这种方法避免了椭圆的拟合过程,减少了引入中间误差过程。     

Modelling ignition probability with pairwise mixing-reaction model for flame particle tracking

Reduced order models for ignition analysis can offer insights into ignition processes and facilitate the combustor optimization. In this study, a Pairwise Mixing-Reaction (PMR) model is formulated to model the interaction between the flame particle and the surrounding cell mixture during Lagrangian flame particle tracking. Specifically, the model accounts for the two-way coupling of mass and energy between the flame particle and the surrounding shell layer by modelling the corresponding turbulent mixing, chemical reaction and evaporation process if present. The state of a flame particle, e.g., burnt, hot gas or extinguished, is determined based on particle temperature. This model can properly describe the ignition process with a spark kernel being initiated in a nonflammable region, which is of practical importance in certain turbine engines and has not been rigorously accounted for by the existing models based on the estimation of local Karlovitz number. The model is integrated into an ignition probability analysis platform and is demonstrated for a methane/air bluff-body flame with the flow and fuel/air mixing characteristics being extracted from a non-reacting simulation. The results show that for the spark location being at the extreme fuel-lean outer shear layer of the recirculation zone, PMR can yield ignition events with a significant number of active flame particles. The mechanisms for the survival of the initial flame particles and the entrainment of the survived flame particles into the recirculation zone are analyzed. The results also show that the ignition probability map from PMR agrees well with the experimental observation: a high ignition probability in the shear layer of the recirculation zone near the mean stoichiometric surface, and low ignition probabilities inside the recirculation zone and the top stagnation region of the recirculation zone. The parametric study shows that the predicted shape of the ignition progress factor and ignition probability is in general insensitive to the model parameters and the model is adequate for quantifying the regions with high ignition probabilities.     

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.     

三维五向编织复合材料的冲击压缩特性及破坏机制

利用分离式霍普金森压杆(split Hopkinson pressure bar,SHPB)实验系统和高速摄像技术对三维五向碳/环氧编织复合材料的动态压缩特性进行研究。通过对编织角为22.3°的试样分别进行沿纵向和横向方向的冲击压缩实验,得到材料在200~1200 s^-1应变率范围内的应力应变曲线,并结合高速摄像记录的动态压缩过程,对不同应变率下材料在高速变形下的渐进破坏规律进行分析。同时,综合试样的宏观破坏特征和微观断口形貌特征,进一步分析材料的破坏模式及破坏机理。结果表明:随着应变率的增加,材料在纵向和横向均具有一定的应变率强化效应,在横向方向的应变率强化效应更为显著;不同加载方向下材料的渐进破坏过程、应力应变曲线特征以及破坏方式均具有明显差异,且随着应变率的增加而发生改变。     

二氧化碳（CO2）气硬树脂砂用促硬剂的研究

本文介绍了一种对碱性甲阶酚醛树脂有促硬作用的盐,在树脂中加入强碱和该促硬剂后,形成了稳定液态粘结剂,吹ＣＯ２气体硬化后可得到较高的即时抗压强度和２４小时抗压终强度。