基于航空煤油重整的SOFC-GT混合动力系统性能

建立了基于航空煤油重整固体氧化物燃料电池-涡轮发动机(SOFC-GT)混合动力系统仿真模型,比较了两种回热方式的重整装置以及不同涡轮布置位置时的系统性能变化,优选出最佳的混合动力系统架构。进一步分析了压气机压比、燃料利用率、燃油流量以及空气流量等运行参数对SOFC-GT混合动力系统性能的影响。研究结果表明:设计点工况下,最佳混合动力系统的发电效率能达到45%,体现出良好的系统性能;当燃料利用率为0.82时混合动力系统的效率和功率最高;随着燃油流量(0.051 1～0.058 4 mol/s)的增加,混合动力系统的效率和功率均增加;而随着压气机压比(2.5～3.3)或者空气流量(37～44 mol/s)的增加,混合动力系统的效率和功率都减小。     

Unsteady wakes-secondary flow interactions in a high-lift low-pressure turbine cascade

Detailed experimental measurements were conducted to study the interactions between incoming wakes and endwall secondary flow in a high-lift Low-Pressure Turbine(LPT) cascade.All of the measurements were conducted in both the presence and absence of incoming wakes,and numerical analysis was performed to elucidate the flow mechanism.With increasing Reynolds number, the influence of the incoming wakes on suppressing the secondary flow gradually increased owing to the greater influence of incoming ...     

肋条结构对气膜冷却凹槽叶尖流动换热的影响

为有效抑制涡轮转子叶尖泄漏并改善叶尖热负荷,采用数值模拟的方法,对5种叶尖肋条结构的高压涡轮带气膜冷却突肩叶片流场进行计算,评估了不同叶尖肋条结构的气热性能.结果 表明:在叶尖增加肋条结构能够有效调控叶尖空腔涡、刮擦涡、肋后涡和冷气肾形涡的路径,从而起到减小叶尖高表面传热系数区,提高叶尖平均气膜冷却效率的作用,同时有效...     

A wall-thickness compensation strategy for wax pattern of hollow turbine blade

As an important index affecting the aerodynamic performance and the structural strength of hollow turbine blades, the wall-thickness precision of the blade is mainly inherited from the positional relationship between the corresponding wax pattern and the internal ceramic core. However, due to locating errors, the actual position of ceramic core is always deviated from the ideal position, which makes it difficult to guarantee the wall-thickness precision of the wax pattern. To solve this problem, a wall-thickness compensation strategy is proposed in this paper. Firstly, based on the industrial computed tomography (ICT) technique and curve matching algorithms, a model reconstruction method is developed, with which the 3D model of a trial wax pattern can be easily constructed. After that, focusing on eliminating the wall-thickness errors of the trial wax pattern, an optimization method for the pose of the ceramic core in the wax pattern is proposed. Then, by mapping the optimal pose of the ceramic core to length adjustments of the locating rods, the wall-thickness errors of the wax pattern can be greatly reduced. A case study is also given to illustrate the effectiveness of the proposed compensation strategy.     

尾迹对低压涡轮端区非定常流动影响的数值研究

为提高尾迹对涡轮端区二次流影响的认识,利用尾迹降低端区损失,采用了数值模拟的方法对T106A非定常工况下的叶栅流动进行模拟,辅以实验进行校核。以上游尾迹对端区附面层的抬升作用和上游尾迹对叶栅通道前部涡系结构的破坏作用为切入点,分析尾迹对端区二次流非定常发展过程的影响。研究发现尾迹中心离开叶栅通道时,尾迹对叶栅端区二次流起抑制作用;当尾迹尾部离开叶栅通道时,尾迹卷起的轮毂附面层激励了端区二次流,使二次流更加活跃。     

局部进气ATR涡轮性能影响因素数值模拟研究

为研究局部进气条件下ATR涡轮内的流动特性,对局部进气涡轮进行定常和非定常数值模拟.定常计算采用冻结转子方法,改变动叶与静叶的周向相对位置研究涡轮内流场特征;改变进气扇区布局、进口参数和局部进气度,研究其对涡轮性能的影响.研究结果表明,对于给定局部进气度,进气扇区整体布局时,涡轮性能的优越性最大;在局部进气ATR涡轮的设计中,需要综合考虑流量、效率和功率3个因素来决定局部进气度.不同位置定常流动结果的平均值与非定常流动的时均值存在差异,非定常计算更好地展示了静叶尾迹和流动积累效应的影响,因而更加可靠.     

Thermodynamic features of aircraft diagonal gas turbines

An effect of the Coriolis forces on the process of gas expansion in the turbine stage is considered. Expressions for efficiency with regard for the radial flow passage are derived. The calculation results and statistical data on the geometric parameters of diagonal stages are presented.     

降低CC50汽轮机推力瓦运行温度研究

针对4#机组汽轮机出现正推力瓦运行金属温度偏高的状况,在深入调查4#机组汽轮机现状的基础上,通过与现有标准相比较,确定目标为正推力瓦运行金属温度≤95℃;在具体分析其影响因素的基础上,确定了5个主要影响因素,并针对其采取了相应措施,改造结果表明确实使4#机组汽轮机组正推力瓦运行金属温度低于95℃,达到了预期目标,为汽轮机的改造提供了技术指导。     

双级高压涡轮气动性能试验状态模化方法

针对双级高压气冷涡轮的低温试验状态模化方法，对以空气为工质、基于不同相似准则数的试验模化状态的流场相似 性进行数值仿真。结果表明：对于有冷气试验模化方法，采用出口马赫数与设计状态一致的模化方法可获得相似性较好的试验状 态流场，此时反力度、载荷系数、马赫数均能保证良好的相似性，主要相似准则数偏差不超过5%；对于无冷气试验模化方法，保持 涡轮几何不变并增大膨胀比使得等熵速比与设计状态的一致，或通过改变叶片数保证各排出口马赫数与设计状态的一致，均能显 著改善无冷气模化状态与设计状态的流场相似性。其中前者反力度相似性接近98%，而后者载荷系数和马赫数的相似性达到了 同样水平，但破坏了模型的几何相似。     

有间隙涡轮叶栅壁面流谱实验与数值模拟研究

对具有 3 .6 %相对叶顶间隙的涡轮叶栅进行了壁面流动显示和三维流场数值模拟 ,分析了大叶顶间隙涡轮叶栅的壁面流动特点 ,从数值模拟上特别对尾缘附近的壁面流动结构进行了详细讨论。实验与计算结果表明叶栅尾缘附近的流动是非常复杂的 ,同时由于叶顶间隙的存在 ,上下尾缘附近的壁面流谱明显不同