高超声速圆锥边界层失稳条纹结构实验研究

边界层转捩的准确预测是高超声速飞行面临的关键气动问题之一。为研究高超声速边界层失稳和转捩机理,以前缘半径1.6mm、半锥角7°的圆锥模型为研究对象,在FD-07高超声速风洞中采用红外热图技术开展边界层转捩实验测量。通过与工程计算结果对比,确认模型表面边界层流态。实验结果表明:有迎角条件下,模型表面中后段出现条纹结构,条纹结构的起始位置随着周向角的增加而向上游移动;随着迎角的增加,条纹起始位置向上游移动,条纹强度差异和条纹与模型中心线的夹角越来越大。实验获得的条纹结构与不同频率扰动波相互作用直接数值模拟获得的条纹结构现象一致。通过对比分析,认为边界层内不同频率扰动波相互作用是产生条纹结构的一种机制。     

DME Interference mitigation for L-DACS1 based on system identification and sparse representation

L-band digital aeronautical communication system 1 (L-DACS1) is a promising candi-date data-link for future air-ground communication, but it is severely interfered by the pulse pairs (PPs) generated by distance measure equipment. A novel PP mitigation approach is proposed in this paper. Firstly, a deformed PP detection (DPPD) method that combines a filter bank, correlation detection, and rescanning is proposed to detect the deformed PPs (DPPs) which are caused by mul-tiple filters in the receiver. Secondly, a finite impulse response (FIR) model is used to approximate the overall characteristic of filters, and then the waveform of DPP can be acquired by the original waveform of PP and the FIR model. Finally, sparse representation is used to estimate the position and amplitude of each DPP, and then reconstruct each DPP. The reconstructed DPPs will be sub-tracted from the contaminated signal to mitigate interference. Numerical experiments show that the bit error rate performance of our approach is about 5 dB better than that of recent works and is closer to interference-free environment.     

LENS风洞试验返回器模型气动热特性模拟

国家数值风洞高超声速流动模拟软件HyFLOW的研制对打破国外同类软件的技术壁垒具有重要意义。与国外DPLR软件进行了对比研究，同时系统介绍了HyFLOW软件求解器的数值方法、物理化学模型以及壁面催化特性计算模型等主要方法，采用典型算例对有限催化模型进行了数值验证，最后基于LENS风洞试验146 mm返回器标模外形开展了高超声速气动热特性数值模拟。研究结果表明，HyFLOW软件在高超声速热化学非平衡流动模拟与评估方面的气动力计算精度高，与国外同类软件DPLR相当，同时其壁面催化条件下的气动热计算精度可靠，可信度高。     

某型飞机通信电台干扰油量系统故障分析

针对某型飞机通信电台干扰油量系统故障，分析了油量测量系统的原理和电磁干扰机理，研究了故障发生的原因，制定了抑制干扰的措施，解决了一直困扰修理的油量指示系统跳变问题，提高了飞机修理质量。     

基于等 Weber 数的结冰外形修正

由于设备条件的限制,在进行结冰风洞试验时,试验 Weber 数与目标 Weber 数往往存在差异,为了获得与目标 Weber 数对应的冰形,需要对试验结果进行修正。本文分析了进行 Weber 数修正的原因,提出了根据几何特征量进行结冰外形修正的方法,并以某超临界翼型为对象,对不同 Weber 条件下的结冰外形进行了仿真,研究了Weber 数变化对结冰的影响规律,在此基础上开展了基于等 Weber 数的结冰外形修正。研究发现：(1)Weber 数主要影响冰角特征,对水滴收集特性、结冰极限及驻点冰厚度影响较小;(2)存在一个敏感 Weber 数,低于敏感值时, Weber 数变化对结冰影响不大,当 Weber 数高于敏感值时,Weber 数变化对结冰有明显影响;(3)采用本文提出的冰形修正方法,能保证冰形的宏观轮廓与目标冰形一致,修正后的冰形能适量消除由于 Weber 数误差导致的冰形差异,提高试验的精度。     

蜂窝式轴心通风器油气分离性能计算

为对航空发动机蜂窝式轴心通风器油气分离效率进行研究,建立考虑油气双向耦合的流场计算方法及油滴/壁面相互作用模型,在验证通风阻力及油气分离效率可靠性的基础上,对不同转速、通风流量和环境温度下蜂窝式轴心通风器的油气分离效果进行计算和分析.结果表明:转速的增加会使油气分离效率得到提升,而通风流量和环境温度的增加则导致油气分离效率的降低.蜂窝孔结构的加入对通风阻力影响不大,却对通风器的滑油分离过程起主要作用,计算表明其对滑油分离贡献率在80%以上.      

展向振荡对激波/湍流边界层干扰的影响

周期振荡作为一种有效的壁面流动控制手段受到广泛关注,而其对激波/湍流边界层干扰的影响目前鲜有研究。本文采用高精度直接数值模拟（DNS）方法对马赫数2.9、12°激波入射角、强振荡下的激波/湍流边界层干扰进行了系统研究。通过与无振荡工况的定量比较,揭示了展向强振荡对干扰区内复杂流动结构的影响规律及作用机制,如分离泡尺度、物面压力脉动非定常特性、物面剪切的非定常特性及统计特征等。研究发现：在展向强振荡作用下,分离点位置提前,间歇区长度增大;同时由于分离泡内强黏性耗散的影响,展向振荡的穿透高度约为分离泡高度的4%,因而对流动结构不会产生实质影响。但展向强振荡会对壁面附近流动造成显著影响,如强振荡诱导的壁面展向速度远大于流向速度,造成流向剪切与展向剪切之间夹角的概率密度函数峰值从0°偏移到80°~90°之间。物面压力及剪切本征正交分解分析表明,展向振荡会导致模态能量从低阶模态向高阶模态转移,降低低频运动的能量占比,增强再附后Görtler涡等壁面附近旋涡结构的强度。     

膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.