SHS法制备硼化物陶瓷粉体的表征分析

采用自蔓延高温还原合成方法制备TiB2,TiB2-Al2O3和ZrB2-Al2O3陶瓷粉末.利用XRD,XPS,SEM以及TEM等分析测试手段对合成粉末进行表征和分析.结果表明,TiB2,ZrB2和Al2O3分别以主晶相的形式存在于所合成的各自粉体之中.相比之下,TiB2单相陶瓷粉末颗粒分布较宽.由于自蔓延高温合成(SHS)温度很高,部分颗粒形成团聚,宏观上使颗粒的平均粒径变大(＞5μm);而TiB2-Al2O3和ZrB2-Al2O3复合陶瓷粉末,因合成过程中Al2O3的形成,使得颗粒粒度分布明显变窄,分布均匀,颗粒尺寸也相应减小.分析认为这主要与复合粉末合成过程中,不同颗粒间形成良好结合的界面有关.     

The role of AVDR in linear cascade testing

Linear cascade testing plays an important role in the research and development of turbomachinery and is widely used over the world.The ideal cascade model of a turbomachinery blade row is two-dimensional.In actual linear cascade testing, the flow through the test section converges due to the development of the boundary layer and secondary flow along the sidewall surfaces of the test section.Axial velocity density ratio(AVDR) is adopted to account for the deviation of the tested cascade flow from the ideal 2D model.Among numerous published cascade works, the influence of AVDR on cascade performance is seen to be complicated with many affecting factors, such as those related to cascade/blade geometry and flow conditions.Also, controlling AVDR is limited by the facility capability.Furthermore, real blade-to-blade flow in turbomachines is usually associated with AVDR greater than unity due to limited span of blades between the hub and shroud such that cascade testing without reducing AVDR could be favored sometimes.All these facets add complexity and diversification to the matter.The current paper reviews previous studies and results on AVDR.Consolidated understanding on the role of AVDR and recommendations on how to deal with it in linear cascade testing are provided.      

基于旋转坐标系转轴振动信号的滚动轴承故障诊断方法

实验验证了基于旋转坐标系转轴振动信号的滚动轴承局部故障诊断方法.建立起滚动轴承故障实验台, 采用压电晶体加速度传感器测取转轴的振动.通过滚动轴承内环、外环、滚动体和保持架四种典型故障的实验分析结果, 证明了该方法的可行性, 并发现转轴振动信号的传递路径相对简单, 对轴承内环、滚动体和保持架早期微小故障的发现与诊断可能是有利的.      

高速旋转部件在载人航天器热控系统中的应用

文章阐述了高速旋转部件在载人航天器热控系统中的应用现状,提出了增长部件寿命、改进系统可靠性的建议并介绍了磁悬浮技术。     

基于热电偶反串的温升效率测量不确定度分析

针对轴流压气机气动性能试验中存在的低压比温升效率评估问题,构建了常规测温方法与反串测温方法测量的温升效率不确定度数学分析模型,并采用某单级压气机真实试验数据进行了两种测温方法不确定度的对比分析。结果表明：相比常规测温方法,反串测温方法不仅消除了热电偶冷端环境温度测量引入的不确定度,还大幅降低了进口温度测量引入的不确定度,使温升效率测量不确定度减小幅度在30%以上。     

惯性导航系统各种传递对准方法讨论

 本文按对准基本原理将惯性导航系统各种传递对准方法分为两大类,一类可称为计算参数匹配法,它包括速度匹配和位置匹配;另一类可称为测量参数匹配法,它包括加速度匹配、姿态匹配和角速度匹配。文中详细讨论了这两类方法的性质,指出:计算参数匹配法类似静基座自对准和空间率对准,在载体无机动动作时对准时间较长。测量参数匹配法对准时间短,但受载体挠性变形的影响大。     

Global Response of Martian Plasma Environment to an Interplanetary Structure: From Ena and Plasma Observations at Mars

As a part of the global plasma environment study of Mars and its response to the solar wind, we have analyzed a peculiar case of the subsolar energetic neutral atom (ENA) jet observed on June 7, 2004 by the Neutral Particle Detector (NPD) on board the Mars Express satellite. The “subsolar ENA jet” is generated by the interaction between the solar wind and the Martian exosphere, and is one of the most intense sources of ENA flux observed in the vicinity of Mars. On June 7, 2004 (orbit 485 of Mars Express), the NPD observed a very intense subsolar ENA jet, which then abruptly decreased within ∼10 sec followed by quasi-periodic (∼1 min) flux variations. Simultaneously, the plasma sensors detected a solar wind structure, which was most likely an interplanetary shock surface. The abrupt decrease of the ENA flux and the quasi-periodic flux variations can be understood in the framework of the global response of the Martian plasma obstacle to the interplanetary shock. The generation region of the subsolar ENA jet was pushed towards the planet by the interplanetary shock; and therefore, Mars Express went out of the ENA jet region. Associated global vibrations of the Martian plasma obstacle may have been the cause of the quasi-periodic flux variations of the ENA flux at the spacecraft location.     

直升机桨叶刚柔耦合特性及计算方法分析

为了研究桨叶刚柔耦合特性,采用中等变形梁模型处理桨叶弹性变形,分别采用小转角和有限转角两种方法处理桨叶绕铰的刚性运动。以桨叶扬起下坠碰撞问题为研究对象。计算分析表明:(1)弹性桨叶存在较明显的刚性运动和弹性变形耦合;(2)挥舞角较小时,两种处理方法计算结果一致,均与试验数据吻合较好;(3)挥舞角较大时,刚柔耦合增强,两种处理方法的计算值差别较为明显;(4)桨叶弯曲刚度对桨叶刚柔耦合特性有较明显影响,刚度越小,耦合越强;(5)桨叶如果比较柔软,小转角处理方法计算值相对有限转角处理方法,相位滞后、幅值增加均较为明显,计算桨叶动响应时需引起注意。      

先进复合材料格栅结构制造工艺技术的研究进展

介绍了复合材料格栅结构的特点及发展现状,并回顾了传统复合材料成型工艺方法和格栅结构的早期制造方法。另外,介绍2种新型的格栅结构加工方法,即混合加工法、膨胀模块加工法以及改进的格栅结构:互锁复合材料格栅结构、加套管的槽形连接格栅结构和TR IG结构;并分别说明了每种结构的优点。其中重点介绍了混合加工法并从理论上推导其可行性。最后总结了复合材料格栅结构制造工艺的发展趋势。     

当量比对连续旋转爆轰燃烧室特性的影响

为了探究当量比对甲烷-空气连续旋转爆轰燃烧室（CRDC）特性的影响,利用二维可压缩欧拉方程对CRDC进行了数值研究,分析了爆轰波的发展过程和贫燃熄火过程,对比了不同工况下CRDC特性参数的变化情况。结果表明:CRDC起爆后燃烧场在由不稳定状态到相对稳定状态的过程中发生了2次碰撞,当进气当量比较低时,CRDC未能完全发生2次碰撞过程就已经熄爆。随着进气当量比的降低,爆轰波传播速度、轴向平均速度、出口平均温度、出口平均总压均呈下降趋势;增压比随当量比降低而减小的根本原因在于旋转爆轰燃烧过程和等压燃烧过程的熵增差减小,使吉布斯自由能增量差减小。CRDC的燃料驻留时间处于亚毫秒量级,燃烧热效率保持在99%以上。