棘爪扁簧断裂故障分析及制造工艺的改进

通过设计计算、对比分析、工艺复装、工艺试验等方法对棘爪扁簧使用中断裂故障进行了分析,并针对性地从设计、工艺两方面进行了改进,经鉴定与试车验证,措施有效,为航空发动机同类零件的研究提供了经验。     

一种叶片截面线光顺及等距面生成方法

采用等距面生成球头刀加工刀具轨迹是曲面加工中一种常用的方法。但是,在对叶身曲面进行等距偏置时,经常出现无法偏置的问题。针对该问题,分析了曲面偏置自相交原因,并根据叶片类零件叶身曲面的特点,提出了一种叶身截面线光顺及等距面生成方法。该方法首先采用Kjellander方法将原始截面线进行自动光顺,然后根据光顺后的原始截面线和数据采样法构造偏置截面线,最后通过截面线放样法构造叶身曲面等距面。实例表明,采用Kjellander方法可以实现叶片曲面的自动光顺和叶片曲面等距面的构造。     

某发动机调节器自动检测异常故障分析

针对某型发动机自动调节器自动检测异常的故障现象,对产生发动机自动调节器自动检测异常的原因进行了深入地研究分析,并提出了针对性的预防措施。     

可控曲率半径的圆柱形叶片逐点绘型方法

针对中低比转速离心泵,根据叶片进出口边界条件,以逐点绘型方法为基础,提出了一种新的曲率半径可控的叶片绘型方法。该方法的主要特点是曲率半径比值可作为设计常量由设计人员根据需要事先给定,随后分析了曲率半径及比例因子对叶片安放角、叶片包角、相对速度及速度矩等的影响。结果表明,不同曲率半径比值下的叶型参数及流动参数变化范围很大,曲率半径比值较大时,节流损失较大,泵扬程较低,曲率半径比值较小时,脱流损失较大,泵效率较低,存在较优的曲率半径比值区间[1.4,2.4],使叶片安放角平滑变化,泵的综合性能较优,在该优化区间内,取较大的曲率半径比值有利于获得较优的汽蚀性能,比例因子为0时叶片安放角的变化较为平稳,可用于开展离心泵的初步设计。     

DME Interference mitigation for L-DACS1 based on system identification and sparse representation

L-band digital aeronautical communication system 1 (L-DACS1) is a promising candi-date data-link for future air-ground communication, but it is severely interfered by the pulse pairs (PPs) generated by distance measure equipment. A novel PP mitigation approach is proposed in this paper. Firstly, a deformed PP detection (DPPD) method that combines a filter bank, correlation detection, and rescanning is proposed to detect the deformed PPs (DPPs) which are caused by mul-tiple filters in the receiver. Secondly, a finite impulse response (FIR) model is used to approximate the overall characteristic of filters, and then the waveform of DPP can be acquired by the original waveform of PP and the FIR model. Finally, sparse representation is used to estimate the position and amplitude of each DPP, and then reconstruct each DPP. The reconstructed DPPs will be sub-tracted from the contaminated signal to mitigate interference. Numerical experiments show that the bit error rate performance of our approach is about 5 dB better than that of recent works and is closer to interference-free environment.     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

某型飞机通信电台干扰油量系统故障分析

针对某型飞机通信电台干扰油量系统故障，分析了油量测量系统的原理和电磁干扰机理，研究了故障发生的原因，制定了抑制干扰的措施，解决了一直困扰修理的油量指示系统跳变问题，提高了飞机修理质量。     

压气机叶片型面精密数控铣加工技术应用研究

为了提高压气机叶片型面和进、排气边转接圆角的数控铣加工质量,在工艺、夹具、数控加工模型与程序以及检测方法等方面采取了攻关措施,减小了叶片型面精铣加工的变形,实现了叶身型面的精密铣削加工,对型面采用毡轮修光去除铣削痕迹后,经过3坐标、小半径投影仪等设备的测量,进、排气边转接圆角的形状和型面轮廓度、位置度各项要求的加工质量得到了质的提升,其合格率由20％提高到75％以上,加工效率和刀具耐用度提高1倍以上,使叶身型面精密铣削技术具备了精品叶片批量生产的工程化应用技术基础.     

基于响应面法的齿轮容差设计方法研究

随着附件传动系统不断向高速、重载方向发展,齿面接触可靠性问题越来越受关注.为提高齿轮可靠性,分析了齿轮传动系统常见误差类型及影响,开展了齿轮容差设计初步探讨.根据齿轮制造、加工及系统动态误差的产生原理和作用方式,基于齿轮接触应力仿真结果,确定了影响齿轮接触应力随机性的5种主要误差形式及其特征量分布规律,提出了基于响应面法的齿轮容差设计方法,给出了齿轮系统公差设计的改进方向:在进行齿轮公差设计时,重点控制H、V方向的轴向平行度公差.     

带自由表面水流的分离涡模拟

目前水动力学问题的数值求解仍然广泛采用RANS模型,特别对于大尺度的地表水流的数值模拟,该类模型计算效率较高,但其难以给出湍流场的小尺度涡结构.深入研究复杂地形条件下的水流运动,需要发展诸如LES等的高级数值模型.天然地表水流,地形、边界复杂,雷诺数通常较高,高级数值模拟受限于计算能力的限制,还难以工程应用.RANS和LES混合模型是目前具有工程应用的一种混合数值模型,其已经在CFD领域获得了长足发展.然而对于地表水流运动的数值模拟,相关工作还较少.本文将分离涡模型(DES),即一种RANS和LES的混合模型,应用于带自由表面的地表水流运动,建立了一套数值仿真模型.模型基于有限体积法,水平面内采用非结构计算网格,垂向为结构化网格,对流项离散格式采用二阶TVD格式,并行基于OpenMP语言库.算例表明DES模型有助于揭示复杂地形条件下带自由表面水流的大涡拟序结构.