一起新材料应用引起的航空机轮故障分析

TC11钛合金在首次应用于某型飞机机轮刹车壳体时,由于对TC11的特性掌握不透,设计考虑不周,造成了使用过程中刹车壳体卡台断裂的故障。通过分析故障原因,制订了改进措施,经试验试飞验证,改进措施有效,为TC11在航空机轮上的推广应用积累了经验。     

TC4钛合金超音频直流脉冲TIG焊

首先对超音频直流脉冲TIG焊的特点进行了介绍,重点分析了的峰值电流、脉冲频率等关键工艺参数对超音频直流脉冲TIG焊电弧轴向等离子流力的影响规律.采用频率不同的几组超音频直流脉冲TIG焊工艺及常规直流TIG焊工艺分别焊接了2.5mm厚的TC4钛合金.用X-射线探伤检测焊缝中的气孔缺陷,根据检测结果,分析了超音频直流脉冲T...     

异种状态TC4 钛合金电子束焊接性能分析

针对相对疏松的铸造钛合金和相对密实的锻造钛合金的焊接问题,开展了两种状态的TC4钛合金电子束焊接工艺研究,对比了不同焊接参数对焊接质量的影响。研究结果表明,采用方波扫描可以较好地实现铸造钛合金与锻造钛合金的连接,焊缝成形良好,内部无缺陷;焊接接头力学性能分析表明,拉伸断裂位置全部在铸件母材区一侧。实焊结果证明,电子束焊接可以实现异种状态TC4钛合金焊接的工程化应用。     

Analytic estimation and numerical modeling of actively cooled thermal protection systems with nickel alloys

Actively cooled thermal protection system has great influence on the engine of a hypersonic vehicle, and it is significant to obtain the thermal and stress distribution in the system. So an analytic estimation and numerical modeling are performed in this paper to investigate the behavior of an actively cooled thermal protection system. The analytic estimation is based on the electric analogy method and finite element analysis（FEA） is applied to the numerical simulation. Temperature and stress distributions are obtained for the actively cooled channel walls with three kinds of nickel alloys with or with no thermal barrier coating（TBC）. The temperature of the channel wall with coating has no obvious difference from the one with no coating, but the stress with coating on the channel wall is much smaller than that with no coating. Inconel X-750 has the best characteristics among the three Ni-based materials due to its higher thermal conductivity, lower elasticity module and greater allowable stress. Analytic estimation and numerical modeling results are compared with each other and a reasonable agreement is obtained.     

航天用铝合金/ 焊丝焊接性研究

针对2A14、2219、2195、2A97、1460铝合金,通过焊接热模拟试验、焊接裂纹敏感性试验和拉伸试验,建立了材料脆性温度区间大小和焊接性的关系及焊丝主成分和焊接性的关系。结果表明,试验合金焊接性从好到差的排列顺序为2219、2A14、1460、2195、2A97。其中2A14、2219铝合金现用焊丝可以满足推进剂贮箱用铝合金焊接性要求。脆性温度区间较小时,焊接性良好,随脆性温度区间增加,焊接性变差;采用满足主成分含量之和为6%的焊丝焊接时,若抗裂性满足要求,则接头延伸率满足要求。     

双层板激光焊接/ 超塑成形数值模拟及工艺研究

选取TC4 钛合金四层板加强结构中双层板为研究对象,采用激光穿透焊接工艺代替传统超塑成

形/ 扩散连接(SPF/ DB)工艺中涂止焊剂连接。借助ABAQUS 有限元分析软件对超塑成形过程进行分析,得到

优化的压力-时间(p-t)曲线,作为双层板超塑成形过程的气压加载曲线,进行实验验证。结果表明:成形后零

件壁厚分布均匀,焊缝处无撕裂现象,与有限元模拟结果保持一致;用此新工艺代替传统SPF/ DB 工艺中的止

焊剂具有可行性。

     

Electromagnetic riveting technique and its applications

With the increasing applications of novel materials and structures in new-generation aircraft, conventional joining techniques in aircraft component assembly are greatly challenged. To meet those challenges, the electromagnetic riveting (EMR) technique was developed as an advanced joining tool, which exhibits obvious advantages in the assembly of new-generation aircraft. In this paper, the riveting principle of EMR was analyzed, and its development history and status were presented in detail. Then, equipment features of three typical EMR systems were given. Moreover, three important applications of EMR were covered, i.e., composite structure riveting, titanium rivet and large-size aluminum rivet riveting, and interference fit bolt installation. Specially, a novel strengthening method for mechanical linking holes based on EMR was also presented, which can significantly improve the fatigue behaviors of mechanical joints. Finally, open questions in the EMR field were discussed, and some recommendations for future work were also made. This paper can be useful for optimizing the joint designs of aircraft components and improving the level of aircraft maintenance.     

Cr对Nb-16Si-22Ti-2Al-2Hf合金显微组织与高低温力学性能的影响

 以Nb-16Si-22Ti-2Al-2Hf成分为基础,分别添加了2%和17%(原子分数,后同)的Cr元素替代Nb(分别称2Cr和17Cr合金),研究了Cr含量对Nb-16Si-22Ti-2Al-2Hf合金相组成、显微组织形貌、室温断裂韧性和高温强度的影响,分析了高低温失效机制。结果表明,铸态和1 375 ℃×100 h热处理后2Cr合金由Nbss和Nb₅Si₃两相组成;当Cr含量为17%时,出现了具有C15结构的Laves Cr₂Nb相,合金由Nbss、Nb₅Si₃和Cr₂Nb三相组成,热处理后在Nb₅Si₃中还析出了球状Cr₂Nb相。随着Cr含量由2%提高到17%,热处理合金的室温断裂韧性K_Q由14.32 MPa·m^1/2下降到10.30 MPa·m^1/2。合金强度与Cr含量的关系受温度影响,随Cr含量提高,室温和1 150 ℃时合金的硬度或强度增高,而1 250 ℃和1 350 ℃时合金强度降低。如1 150 ℃时2Cr和17Cr合金的屈服强度σ_0.2分别为349 MPa和387 MPa;1 350 ℃时分别为306 MPa和74 MPa。     

TC21-0.28%H钛合金微观组织及其高温变形行为研究

利用光学金相及X射线衍射,研究了TC21-0.28%H(质量分数,下同)钛合金的组织结构,通过热模拟压缩实验,研究了TC21-0.28%H钛合金在800～920℃温度范围和0.01～1s-1应变速率范围的高温变形行为,建立了钛合金高温变形本构方程。结果显示,与TC21钛合金相比,TC21-0.28%H钛合金β相比例显著增加,并且有新相马氏体α″与氢化物δ生成,TC21-0.28%H钛合金在α+β相区与β相区的变形激活能分别为233kJ/mol与153kJ/mol,软化机制为动态回复,与TC21钛合金相比,TC21-0.28%H钛合金变形激活能降低,热加工性能得到改善。     

TA15 钛合金等温局部加载各加载区的组织和性能

研究了不同加载方式下TA15钛合金方坯先加载区、过渡区和后加载区的组织和力学性能。结果表明:只采用局部加载时,先加载区和后加载区的室温和高温性能优于过渡区的性能,各区的持久性能差别不大;采用先局部后整体的加载方式时,过渡区的室温和高温性能优于其他两个加载区,但过渡区的持久性能明显较差。只采用局部加载时,各区的组织性能优于先局部后整体加载时各区的组织性能。