全文获取类型
收费全文 | 412篇 |
免费 | 57篇 |
国内免费 | 153篇 |
专业分类
航空 | 482篇 |
航天技术 | 61篇 |
综合类 | 58篇 |
航天 | 21篇 |
出版年
2024年 | 2篇 |
2023年 | 6篇 |
2022年 | 11篇 |
2021年 | 19篇 |
2020年 | 17篇 |
2019年 | 5篇 |
2018年 | 8篇 |
2017年 | 29篇 |
2016年 | 35篇 |
2015年 | 21篇 |
2014年 | 24篇 |
2013年 | 18篇 |
2012年 | 43篇 |
2011年 | 27篇 |
2010年 | 24篇 |
2009年 | 36篇 |
2008年 | 29篇 |
2007年 | 23篇 |
2006年 | 17篇 |
2005年 | 19篇 |
2004年 | 17篇 |
2003年 | 15篇 |
2002年 | 12篇 |
2001年 | 19篇 |
2000年 | 14篇 |
1999年 | 17篇 |
1998年 | 16篇 |
1997年 | 16篇 |
1996年 | 17篇 |
1995年 | 18篇 |
1994年 | 24篇 |
1993年 | 3篇 |
1992年 | 3篇 |
1991年 | 5篇 |
1990年 | 6篇 |
1989年 | 3篇 |
1988年 | 4篇 |
排序方式: 共有622条查询结果,搜索用时 15 毫秒
21.
22.
It is difficult to construct the prediction model for titanium alloy through analyzing the formation mecha- nism of surface roughness due to the complicated relation between influential factors and surface roughness. A no- vel algorithm based on the modified particle swarm optimization (PSO) least square support vector machine (LS- SVM) is proposed to predict the roughness of the end milling titanium alloys. According to Taguchi method and features in milling titanium alloys, the influences of cutting speed, feed rate and axial depth of cut on surface roughness are investigated with the analysis of variance (ANOVA) of the experimental data. The research results show that the construction speed of the modified PSO LS-SVM model is two orders of magnitude faster than that of back propagation(BP) model. Moreover, the prediction accuracy is about one order of magnitude higher than that of BP model. The modified PSO LS-SVM prediction model can explain the influences of cutting speed, feed rate and axial depth of cut on the surface roughness of titanium alloys. Either a higher cutting speed, a lower feed rate or a smaller axial depth of cut can lead to the decrease of surface roughness. 相似文献
23.
针对TC11薄壁叶片在数控加工过程中存在振动问题,采用单因素试验法进行薄壁叶片的铣削试验,建立铣削参数对振动加速度的影响模型,分析各铣削参数对铣削振动的影响规律,运用工艺参数区间敏感性分析方法,优选了铣削工艺参数区间。 相似文献
24.
以1mm厚Ti-6Al-4V合金薄板为对象,运用光学金相显微镜、电子探针、扫描电子显微镜、氮氢氧联合分析仪、显微维氏硬度计,研究了特定累积线能量下90°弯曲角弯折区显微组织。结果表明,弯折区组织与累积线能量输入有关,当累积线能量在适当范围时,材料堆积增厚,极表层出现轻微复熔铸态组织,上层为板条马氏体α′,中层为针状马氏体α′,底层为长大粗化的(α+β)组织;距表层约0.2mm范围吸收间隙元素强烈致使硬度急剧提高并呈明显梯度;累积线能量输入过大,弯折区出现大面积复熔铸态组织并伴有裂纹产生。 相似文献
25.
航空发动机钛火防护技术及试验验证方法 总被引:1,自引:1,他引:0
钛合金在航空发动机上应用广泛,特别是对于追求高推重比的军用发动机更是如此。但采用钛合金存在钛火风险,且钛火故障危害大、发生频率高。分析了钛火故障产生的原因,描述了故障导致的后果,并结合发动机上典型钛火故障,总结了4种较为有效的钛火防护设计技术。阐述了钛火防护技术的试验验证方法和目的,指出只有通过试验验证,才能确认钛火防护技术的安全有效。 相似文献
26.
27.
The influences of rare earth element Nd on the phase transformation and the microstructure of Ti50Ni48−xFe2Ndx shape memory alloys are investigated by means of electrical resistivity, optical microscopy, electron probe microanalyzer, and X-ray diffraction. The results show that TiNiFe alloys with different Nd contents exhibit two-step martensitic transformation. The start temperature of martensitic transformation increases sharply from 212 K to 267 K when 0.1 at.% Nd is added in, and then decreases gradually if Nd content further increases. The microstructure of TiNiFeNd quaternary alloys consists of TiNi matrix, Ti2Ni second phase, and Nd3Ni intermetallic compound. The spherical Nd3Ni precipitate-particles evenly disperse in the matrix. 相似文献
28.
蔡军%李付国%任东升%王家臣 《宇航材料工艺》2008,38(6)
文摘为了生产出质量合格的叶片,针对TC4合金叶片的成形特点,为其制订了相应的热模锻成形工艺。同时采用基于有限体积的材料成形模拟技术,对TC4合金叶片热模锻过程进行了模拟,分析了坯料成形过程中的充填情况、应变场、应力场及终锻温度场的分布规律。模拟结果表明:锻件轮廓清晰,模具型腔充填完整,未出现充不满或折叠等锻造缺陷。实际生产出来的叶片经理化检测和外观检查,质量符合要求,制定的工艺方案合理,可以满足TC4合金航空风扇转子叶片的成形质量要求。 相似文献
29.
SmCox-0.4Ti0.4(x=5.0, 5.5, 6.5, 7.0)合金经42m/s速度甩带快速凝固制成薄带,在真空热处理炉中,进行750℃两小时热处理.对制得的甩带状态和热处理状态合金薄带分别测试其相结构和磁性能.结果表明:SmCox-0.4Ti0.4合金甩带状态样品相结构随Co含量的不同而变化,其中x=5.0,5.5和6.5的合金样品由2∶ 17和1∶ 5两相结构组成;x=7.0成分样品由1∶ 7单相结构组成.甩带状态样品的比饱和磁化强度和比剩余磁化强度基本上线性增加,内禀矫顽力在合金成分为x=5.0时出现最大值,为1.01T.薄带样品热处理前后均具有纳米晶结构,表现出剩磁增强效应.样品矫顽力机制主要为形核型,反磁化形核场主要来源于SmCo硬磁相大的磁晶各向异性及其纳米晶结构.热处理后,除x=7.0样品外,其余样品矫顽力均有所下降. 相似文献
30.
TC4+TC17线性摩擦焊接头的微观组织与力学性能 总被引:5,自引:0,他引:5
进行了TC4+TC17异种钛合金试件的线性摩擦焊实验,利用光学显微镜、扫描电镜及透射电镜分析了焊接接头的微观组织,并进行了焊后接头的力学性能测试.着重分析了焊接接头的焊缝、近缝区及变形区的组织特点及相变规律,并结合线性摩擦焊的工艺特点,初步分析了形变组织的形成机理.实验结果表明,利用合理的焊接工艺参数,用线性摩擦焊方法可获得可靠的Tc4+TC1钛合金焊接接头,接头的拉伸性能优于TC4母材.TC4与TC17接头的焊缝区为等轴细品组织,两侧近缝区、变形区的组织形貌差异较大. 相似文献