基于RANS/LES混合方法的分离流动模拟

飞行器在大迎角、快速俯仰机动时,流场中含有大尺度、非定常的涡结构,传统雷诺平均Navier-Stokes （RANS）模型不能准确模拟流场结构,根据国际上相关研究的发展趋势,需要采用混合RANS/大涡模拟（LES）模型来对复杂分离流动进行准确模拟。本文对基于分区混合与湍流尺度混合的双重RANS/LES混合计算模型进行发展与应用。通过典型简化模型的静、动态湍流大分离流动,测试和验证所采用的脱体涡模拟（DES）类方法,重点研究改进的延迟DES （IDDES）模型在动态问题应用中的正确性和有效性,并对所采用的数值模拟方法和相应的计算软件的可靠性、鲁棒性以及精度进行了考核验证。典型算例包括超声速圆柱底部流动、跨声速方腔流动、NACA0015机翼深失速分离涡模拟等。计算表明：发展的IDDES类混合计算模型可有效解决对数层不匹配的问题;对于定态非定常分离流动,DES、DDES、IDDES等模型计算结果差别不大,随着流动的非定常特性增强,IDDES模型的优势逐渐显现;对于动态非定常分离流动,则需要采用IDDES类模型。     

发动机唇口电热防冰系统性能仿真

采用三维耦合传热方法对发动机唇口电热防冰系统进行了多状态下的性能仿真,获得了唇口表面平衡温度及动态温升响应时间,以此评估防冰系统性能,并通过与冰风洞试验结果对比,对仿真过程进行了修正。研究表明:唇口表面加热区平衡温度均高于273.15 K,温升响应时间小于60 s,满足防冰需要,较为严酷的防冰状态点主要为飞行速度较大、环境温度较低的状态点;修正唇口材料导热系数后,仿真与试验结果吻合良好。研究结果能有效指导工程研制,对提高防除冰仿真分析结果的准确性提供了很好的借鉴。     

Corrosion mechanism investigation of TiN/Ti coating and TC4 alloy for aircraft compressor application

It is imperative to develop multifunctional erosion and corrosion resistant coatings for compressor blades of aircraft engines in harsh environment. PVD (Physical Vapor Deposition) technology has the advances in processing erosion-resistant coatings; however, the performance of PVD coatings to combat corrosion depends on various coating defects. Determining and comparing the corrosion performances of PVD TiN/Ti coating and uncoated TC4 alloy was the main objective of present work. The 960 h salt spray corrosion and 116 h hot corrosion tests were conducted to simulate the grounding and working environments of the aircraft compressors. The corrosion mechanisms due to the coating defects such as pinhole, columnar boundary and large grain were analyzed based on the OM, Confocal microscope, electrochemical measurements, SEM, XRD and EDS results. Owing to the disordered state associated with the columnar boundary and the coating defect, nitrogen could be easily replaced by oxygen in the hot corrosion process, these structures were channels for fast diffusion of oxygen. Moreover, the Gibbs energy changes of Ti oxidation and TiN oxidation were thermodynamically calculated according to the working condition of aircraft compressors, and considerable research effort was focused on mapping out the phase diagram of Ti, TiN and high pressure gases. The findings of this research can provide insights into developing multifunctional coatings for future aircraft engines.     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

石墨填料对浸渗热解-熔融浸渗方法制备的C/SiC复合材料结构和性能的影响

采用石墨树脂浆料浸渍三维针刺碳毡增强体,热解后得到C/C多孔体,并采用反应熔体浸渗法制备C/SiC复合材料.研究了石墨填料对C/C多孔体的结构以及C/SiC复合材料力学性能的影响.结果 表明,石墨树脂浆料浸渍时树脂填充束间小孔形成结构致密的亚结构单元,而石墨可以有效填充胎网层等大孔隙,一次浸渍热解后碳产率有效提高.所得...     

碳/碳复合材料表面纳米HAp/壳聚糖生物复合涂层的制备

以声化学法合成的纳米羟基磷灰石(HAp)为起始原料,以异丙醇作为分散介质,采用水热电泳沉积法在经壳聚糖(CS)溶液改性后的碳/碳复合材料(C/C)表面沉积纳米HAp/CS生物复合涂层.重点研究了水热条件下沉积电压对复合涂层的晶相组成、形貌和结构的影响规律.采用X-射线衍射仪(XRD)、透射电子显微镜(TEM)、傅立叶变换红外光谱分析仪(FTIR)和场发射扫描电子显微镜(FE-SEM)对所制备的涂层进行表征.结果表明:随着沉积电压的升高,涂层更加致密和均匀;同时水热环境有利于纳米HAp晶粒的生长,制备出的HAp/CS复合涂层不需要后续热处理.     

雨流计数的递归算法

给出了疲劳分析中雨流计数法的另一种等效解释。在这个解释的基础上,提出了雨流计数的递归算法。该算法将包含多于一个应力峰值点的任意载荷 时间历程以两个谷值点为界分解成3个子段,每个子段用递归方法继续分解成3个更短的子段,直至每个子段仅包含一个峰值点或不包含峰值点为止。分解得到的仅包含一个峰值点的任意子段对应一个子循环,其应力的最大值和最小值在递归分解过程中可以同时算出。该算法不需像其他雨流计数算法那样在剔除局部子循环的峰、谷点数据后重新整理载荷 时间历程,也能保留各应力子循环出现的先后次序信息,且最先分离出来的可以是变程最大的应力循环。算法的缺点是不适合实时疲劳损伤计算,且算法在实现时需要计算机为其堆栈分配较多的存储器空间。     

大型飞机迎角/过载限制器设计

根据典型大型飞机迎角/过载限制器的特点,提出了两种采用积分控制来减小静态误差的大型飞机迎角/过载保护方法,即最大值切换逻辑和加权过渡逻辑方法,深入研究了如何设计迎角/过载限制器参数,探讨了采用以上两种不同方法来进行迎角与过载限制器切换的优劣,系统仿真结果证明了所设计的限制器的有效性。该项研究为我国未来大型飞机如何设计迎角/过载限制器提供了部分理论依据。     

不同碳黑填料含量2D—SiCf／SiC复合材料介电及雷达吸波性能研究

对先驱体浸渍裂解工艺(PIP)制备的含碳黑填料2D-SiCf/SiC复合材料介电以及雷达吸波性能进行研究.研究表明,由于KD-Ⅰ型SiC纤维表面具有连续碳涂层,不能直接用于吸波材料,需通过空气热处理手段将其除去.对纤维表面去碳后制成的不同碳黑填料含量2D-SiCf/SiC复合材料微波介电常数进行测试,结果表明,随碳黑含量增加,复合材料介电常数明显增大,但由于碳黑的高比表面和先驱体溶液粘度的限制,复合材料中碳黑体积分数最大仅能达到7%～8%,介电常数难以继续增大,介电损耗低于0.3,并且介电常数频散效应不理想.对不同碳黑填料含量复合材料反射率进行计算,结果表明,单层复合材料在某一频段内具有较好的吸波性能,但由于复合材料介电常数频散效应较差,宽频吸波性能不理想,采用不同吸收剂含量复合材料层铺工艺可能可以解决吸波性能带宽问题.     

液氧/煤油补燃发动机低频频率特性研究

基于模块化层次化的建模技术,建立液氧/煤油补燃发动机的线性小扰动频率特性仿真模型.在建模过程中,重点考虑了绝热流动假设和熵波影响下的气路模型.依据交流流体网络理论,运用传递函数法分析了该型发动机的低频频率特性,为研究液体火箭的纵向耦合振动(POGO)及发动机动力学提供帮助.