Forming and keeping fast fly-around under constant thrust

A new switching control algorithm under constant thrust is designed for the chaser fast flying around the target spacecraft along a specified fly-around trajectory. The switching control laws are obtained based on the acceleration sequences and the on time of thrusters which can be computed by the time series analysis method. The perturbations and fuel consumptions are addressed during the computation of the on time of thrusters. Furthermore, the relative position parameters of the target spacecraft are obtained by using the vision measurement and the target fly-around positions are calculated through the isochronous interpolation method. The change of the relative position and the relative velocity of the chaser during the constant thrust fast fly-around are presented through simulation example. It is proved that, with the switching control laws, the chaser will fast fly around the target spacecraft along the specified fly-around trajectory.     

发动机不可控高推力适航部分豁免方法研究

介绍了发动机不可控高推力(UHT)问题的产生背景,论述了申请§25.901(c)条款有关不可控高推力的部分豁免的思路和方法.结合FAA关于不可控高推力的指导材料,给出了有关不可控高推力的持续适航工作建议,对于飞机申请§25.901条款有关不可控高推力的部分豁免具有一定的指导意义     

连续推力机动轨道优化设计的贝塞尔曲线法

提出一种基于贝塞尔曲线的平面机动轨道设计方法。该方法将贝塞尔曲线方程与轨道形状方程相结合，利用得到的复合函数作为轨道方程来对机动轨道进行数学描述；通过约束条件获得可行的机动轨道族，由控制点设计给出具体的优化变量，将累积速度增量作为优化指标函数；并利用优化算法完成参数优化，从而得到最优机动轨道。最后针对设计的机动轨道推力峰值较大的问题，进一步提出了分段贝塞尔曲线法，在降低推力峰值的同时，可进一步降低燃料消耗，并在平面机动转移轨道设计的基础上，通过梯度下降对自由控制点进行修正，解决了考虑时间约束的平面轨道交会问题。     

微小推力下小卫星的轨道递推与推力标定

针对采用微小推力进行轨道机动的小卫星,考虑复杂摄动力的基础设计了一种高精度轨道外推和推力在轨标定算法.首先,建立了考虑地球复杂摄动力和微小推力的小卫星轨道动力学模型;然后基于动力学模型,利用变步长龙格库塔算法,设计了对微小推力小卫星进行高精度轨道外推的方法.随后通过无迹卡尔曼滤波器(UKF),设计在轨标定算法,对存在误...     

推力室逆置点火瞬时真空舱流场数值与试验研究

针对高空模拟舱内逆向布置的推力室点火瞬时过程中舱内压力的变化规律进行了理论和数值仿真分析,推力室高速气流的动能是推力室短程点火过程中舱内压力大幅上升的主要原因.为保证推力室点火时舱内的真空度,需要在推力室出口配置导流装置将燃气导出真空舱.对单台和4台并联推力室进行点火试验,试验表明：采用燃气导流能够较好保持舱内真空度,是整机多推力室高空模拟试验的新思路.     

涡扇发动机性能退化缓解控制与推力设定

为了补偿性能退化发动机的推力损失,减轻飞行员工作负担,提高推进系统的自动化程度,开展了涡扇发动机性能退化缓解控制(EPDMC)研究。针对某型涡扇发动机部件级模型设计了具备稳态控制、加/减速过渡态控制和极限保护等功能的基准控制器;在此基础上设计了外环推力控制回路,给出1种在多参数约束下的推力设定方法,并设计了合理的切换逻辑确保内外环控制器能协调工作。MATLAB/Simulink下的仿真结果表明:该智能改进控制系统架构可以在保证发动机安全工作的前提下,通过合理地设定期望推力,最大程度地补偿推力损失,维持油门杆角度和推力的对应关系近似不变。     

TVC/PSM飞机的过失速动态边界及敏捷性分析

以飞机为质点，考虑在最少输入数据情况下，曲于转弯速率图并从能量的角度计算和分析了TVC/PSM飞机的过失速动态边界，选取敏捷性尺度空战周期时间和指向裕度，对比分析了TVC/PSM飞机和传统飞机的敏捷性，得出了一些有益的结论，并提出了一些建议。     

基于有限Fourier级数的航天器转移轨迹设计

针对航天器小推力转移轨迹的初始设计问题，利用基于三阶Fourier级数的设计方法实现了航天器小推力的多圈转移。同时，基于有限Fourier级数的形状法，对具有多个约束条件的小推力多圈转移轨迹进行了优化设计。选取了共面同轴同偏心率的初始和末端轨道位置，对所提出的方法进行了仿真验证。结果表明：与改进逆五阶多项式形状法相比，所提出的方法虽然增加了转移时间，但当转移圈数为5圈、有限Fourier级数的项数为10时，可减少将近75%的转移速度增量，同时大大减小了所需的最大推力加速度的值。     

某飞行器推力矢量试验测力装置研制

为满足某飞行器推力矢量试验的测试要求,采用两台六分量应变天平和一个空气桥组成测力装置来实现飞机全机气动力和喷管推进特性同时分别测量。基于有限元软件,对天平的应变及空气桥对天平的干扰进行了分析。结果表明:空气桥对天平力分量的干扰值优于5%,对力矩(滚转力矩除外)分量的干扰值优于15%,达到了设计指标。通过校准获得了单独天平、天平带空气桥(充压、不充压)状态下的校准公式,校准结果表明:两台天平各分量的综合加载误差均优于0.3%,天平带空气桥(充压、不充压)状态下各分量的综合加载误差优于0.5%,空气桥对天平的干扰量值与有限元分析结果一致。理论分析与实测结果证明:研制的天平及空气桥达到了预定目标,它的测量精准度高,满足推力矢量风洞试验需求。     

A novel control method for turboshaft engine with variable rotor speed based on the Ngdot estimator through LQG/LTR and rotor predicted torque feedforward

In order to compensate for the disturbance of wide variation in rotor demanded torque on power turbine speed and realize the fast response control of turboshaft engine during variable rotor speed, a cascade PID control method based on the acceleration estimator of gas turbine speed (Ngdot) and rotor predicted torque feedforward is proposed. Firstly, a two-speed Dual Clutch Transmission (DCT) model is applied in the integrated rotor/turboshaft engine system to achieve variable rotor speed. Then, an online estimation method of Ngdot based on the Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR) is proposed for power turbine speed cascade control. Finally, according to the cascade PID controller based on Ngdot estimator, a rotor demanded torque predicted method based on the Min-batch Gradient Descent-Neural Network (MGD-NN) is put forward to compromise the influence of rotor torque interference. The simulation results show that compared with cascade PID controller based on Ngdot estimator and the one combined with collective pitch feedforward control, the novel control method proposed can reduce the overshoot of power turbine speed by more than 20%, which possesses faster response, superior dynamic effect and satisfactory robustness performance. The control method proposed can realize the fast response control of turboshaft engine with variable rotor speed better.