高压涡轮主动间隙控制系统机匣模型试验

设计和搭建了叶尖主动间隙控制系统的核心——可控热变形机匣模型试验验证台,利用机匣温度和变形量等参数的测量,验证了某主动间隙控制设计方案的基本工作特性.试验中通过改变集气腔进气流量,研究了不同试验工况下机匣温度分布规律,获得了机匣径向变形量及其在周向和轴向的分布规律.研究中发现冷却空气管的多孔冲击射流可以有效改变机匣温度,并达到调节机匣变形的最终目的.随着供气雷诺数增加,机匣的热响应时间减小,机匣的收缩速率明显增加,但该增加幅度随着雷诺数的增加而逐步减弱.试验结果表明:机匣径向冷却收缩量基本均匀.由于冷却空气管周向流量分配不均匀,使其周向上最大相对偏差为8.75%.同时冷却空气管结构和供气量差异会导致机匣轴向温度分布不均匀,在该验工况中,机匣径向冷却收缩量在轴向上最大的相对偏差为6.99%.      

Effect of sodium tartrate concentrations on morphology and characteristics of anodic oxide film on titanium alloy Ti–10V–2Fe–3Al

The effect of sodium tartrate concentrations on morphology and characteristics of ano-dic oxide film on titanium alloy was investigated. The alloy substrates were anodized in different concentration solutions of sodium tartrate with the addition of PTFE emulsion and their morphol-ogy and characteristics were analyzed. The anodic oxide film presented a uniform petaloid drums and micro-cracks morphology. Additionally, micro-cracks dramatically swelled with the increase of the tartrate concentrations. The thickness of the anodic oxide film increased with the concentra-tions until the concentration reached 15 g/L. The results of Raman analysis illustrate that all sam-ples have similarity in the crystal structure, consisting of mainly amorphous TiO2, some anatase TiO2 and a small amount of rutile TiO2. And the ratios of anatase TiO2 and rutile TiO2 increase with the concentrations until it reaches 15 g/L. Furthermore, the intensity of the peaks increases with enhanced concentrations until the concentration reaches 15 g/L. The corrosion resistance of the anodic oxide film is increased by the sodium tartrate with higher concentrations before 15 g/L. The coefficient of friction of the anodic oxide film reduces with the concentrations until the concentration reaches 15 g/L, then the coefficient of friction of the anodic oxide film increases with the concentrations.     

高超声速复杂气动问题数值方法研究进展

高超声速流场具有复杂流动特征,其中真实气体效应、磁流体干扰效应和力热结构耦合效应等对气动力分析产生了重要影响。将流体力学研究扩展到分子动力学、电磁流体力学以及流固耦合等交叉学科领域,这给数值模拟方法带来了巨大挑战。针对高超声速气动力/热分析的热点问题,重点关注高温效应与低密度流动效应、磁流体干扰效应和力热结构耦合效应等,结合算例分析了相应的数值求解技术;在气动热方面主要比较了3类求解方法(纯工程方法、纯数值方法和基于Prandtl边界层理论的方法),并给出了相应算例;对于气动力/热/结构耦合问题,从耦合模型及耦合计算方法两方面开展了分析。最后指出了高超声速复杂气动问题数值求解技术未来需重点关注的几个方面。     

An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.     

含裂纹金属薄板的断裂韧度与剩余强度研究

为了探究影响含裂纹铝合金薄板材料断裂韧度、剩余强度的几何因素以及韧性材料的断裂机理,对典型航空铝合金2524-T3薄板,采用不同宽度、不同初始裂纹长度的中心裂纹板试样进行试验,测定材料的K-R阻力曲线,确定平面应力断裂韧度Kc和表观断裂韧度Kapp.试验结果表明:对于薄板结构,K-R阻力曲线与板宽相关;试件宽度、初始裂纹长度对断裂韧度和表观断裂韧度的确定都有影响,且板宽度的影响较大.基于上述结论,推荐两种可同时反映韧性材料断裂中的净截面屈服效应和韧性撕裂过程的剩余强度预测方法.     

Ω长桁和T长桁的工艺对比分析研究

在飞机复合材料蒙皮类构件的设计制造过程中,早期设计阶段,对不同长桁结构进行工艺对比分析研究,有助于提高加筋壁板的结构性能、便于工艺优选、节约制造成本,实现面向制造的低成本最优化设计。针对飞机复合材料蒙皮与Ω长桁、T长桁共固化的典型结构,阐述二者的制造流程及工艺特点;从制造工艺、工时、花费、产品重量和抗冲击性能等方面,对比Ω长桁和T长桁的优缺点;提出在飞机设计制造的并行工程中进行不同结构工艺分析的方法。结果表明:Ω长桁相对T长桁,具有重量轻、抗冲击性能好等优点,但其制造工艺更为复杂,报废率高,制造成本较高。     

7150铝合金热变形行为及微观组织

采用Gleeble热模拟机进行热压缩实验,研究7150铝合金在变形温度为300~450℃、应变速率为0.01~10s-1条件下的变形行为,采用Zener-Hollomon参数法构建合金高温塑性变形本构方程,并对变形后的微观组织进行分析。研究表明:7150铝合金的流变应力随应变速率增大而增大,随变形温度增大而降低。该合金热压缩变形的流变应力行为可用双曲正弦形式的本构方程描述,其参数A为4.161×1014s-1,α为0.01956 MPa-1,n为5.14336,热变形激活能Q为229.7531k J/mol。随着温度升高和应变速率降低,动态再结晶逐渐取代动态回复成为合金的主要软化机制。     

接触特性对非连续性转子热致振动的影响

针对燃气轮机转子的非连续性结构间存在的接触特性,根据微凸体理论引入接触刚度和接触热阻的等效模型,建立了某型燃气轮机非连续性转子的动力学模型,分析了接触参数对转子稳、瞬态动力学特性的影响,研究了螺栓松动引起的转子热变形及其对转子快速启动过程中振动特性的影响.结果表明:预紧力、接触面的表面粗糙度和螺栓个数对转子临界转速有一定的影响,螺栓松动导致转子在启动过程中瞬态热变形最大达到7μm,过1阶临界转速时引起的转子最大响应幅值增大约30μm.在非连续性转子系统的热致振动特性分析当中,不应忽视接触参数、接触刚度和接触热阻的影响.      

基于PCA-TN的直升机主减速器通用热分析计算

针对当前热分析方法无法满足直升机主减速器结构复杂多变的问题,提出了一种快速获取主减速器温度场分布的通用热分析方法。以典型直升机主减速器为样本,进行了主成分分析（principal component analysis,PCA）,并结合热网络法（thermal network,TN）,分析获得3种通用热分析单元体模型。对于不同结构的主减速器,通过单元体及其衍生体的组合可以迅速且有效地建立其系统热分析模型,求解获得温度场分布。以某直升机主减速器为例,应用该方法进行了热分析,并与试验进行了对比,结果表明:该方法能高效计算主减速器的温度场分布,计算值与试验值最大误差为5.07%,满足主减速器热分析工程计算需求。      

航空发动机主轴承接触应力精确仿真计算方法

采用稳态热分析与动态接触力学分析相结合的方法以提高计算精度,考虑轴承摩擦生热及瞬态冲击效应的影响,得到经热应力修正的轴承应力分布及变化特征。研究表明:最大动态接触应力位于钢球表面,外圈滚道次之,内圈滚道最小;轴承接触应力具有明显动态冲击响应特性,分布及大小具有随机变化性;接触应力由主应力与剪切应力共同构成,随转速及轴向载荷增大而增大。