舵机滚珠丝杠在内部热源作用下响应特性

舵机滚珠丝杠在运行过程中由于摩擦作用和电机运行产生的内部热源会导致其结构温度上升和变形,是影响滚珠丝杠副运行精度的因素之一。本文基于有限元理论建立舵机滚珠丝杠副模型,并通过在ANSYS Workbench中插入命令流的方式实现了在滚珠丝杠上施加移动摩擦热载荷,获得了滚珠丝杠副在内部热源作用下的温度、变形和应力响应特性。结果表明:滚珠丝杠轴向热流密度呈双峰趋势,且其高温区域主要集中在螺母行程范围内的中间区域;随着转速的增加,滚珠丝杠各处温度及其波动幅度加大;丝杠最大热应力位于与轴承配合的轴肩最外侧处。     

高温铝合金电磁超声检测回波特性及因素分析

针对高温铝合金在线检测条件下,温度对铝合金电磁超声检测回波特性的影响规律尚不明确、高温检测时缺陷定量/定位补偿困难这一难题,以螺旋线圈电磁超声换能器（EMAT）为例,建立了高温铝合金EMAT检测过程的场路耦合有限元模型;研究了温度对EMAT激励/接收换能效率、EMAT激励/接收电路的功率分配特性、超声传播过程中的扩散/介质衰减特性、回波幅值和超声声速等因素的影响规律;研制了耐高温EMAT探头,对20~500℃高温铝合金试样进行了检测实验,并测定了高温铝合金的超声介质衰减系数和超声声速。在仿真和实验相结合的基础上,分析了高温检测时超声回波幅值变化特性及其影响因素。结果表明：对于铝合金这类非铁磁性金属材料,导致高温时超声回波幅值下降的主要原因是超声介质衰减系数随着温度的升高而增大,其次为高温时EMAT激励/接收电路的功率分配特性的改变。在激励EMAT在试样表面形成的洛伦兹力不变的条件下,其所激励的超声波回波幅值具有随着温度的增加而增加的特点,可以有效减缓超声回波幅值下降的趋势。     

基于隐式温度修正的二维热线风速仪校准方法

热线风速仪主要用于湍流流场测量。热线测量的主要误差来源是由环境温度变化导致的热线校准参数的变化。Brunn提出的传统温度效应修正方法在环境温度变化较大的情况下会带来明显的误差。本文经过理论推导,提出了一种新的基于隐式温度修正的二维热线风速仪校准方法,并开展了热线校准实验研究。结果表明:当环境温度变化在4℃范围内时,本文提出的方法与Brunn方法的测量精度相当;当环境温度变化超过4℃时,本文提出的方法的测量精度远高于Brunn方法。     

基于热电偶反串的温升效率测量不确定度分析

针对轴流压气机气动性能试验中存在的低压比温升效率评估问题,构建了常规测温方法与反串测温方法测量的温升效率不确定度数学分析模型,并采用某单级压气机真实试验数据进行了两种测温方法不确定度的对比分析。结果表明：相比常规测温方法,反串测温方法不仅消除了热电偶冷端环境温度测量引入的不确定度,还大幅降低了进口温度测量引入的不确定度,使温升效率测量不确定度减小幅度在30%以上。     

Cluster observations showing the indication of the formation of a modified-two-stream instability in the geomagnetic tail

This study presents several observations of the Cluster spacecraft on September 24, 2003 around 15:10 UT, which show necessary prerequisites and consequences for the formation of the so-called modified-two-stream instability (MTSI). Theoretical studies suggest that the plasma is MTSI unstable if (1) a relative drift of electrons and ions is present, which exceeds the Alfvèn speed, and (2) this relative drift or current is in the cross-field direction. As consequences of the formation of a MTSI one expects to observe (1) a field-aligned electron beam, (2) heating of the plasma, and (3) an enhancement in the B-wave spectrum at frequencies in the range of the lower-hybrid-frequency (LHF). In this study we use prime parameter data of the CIS and PEACE instruments onboard the Cluster spacecraft to verify the drift velocities of ions and electrons, FGM data to calculate the expected LHF and Alfvèn velocity, and the direction of the current. The B-wave spectrum is recorded by the STAFF instrument of Cluster. Finally, a field aligned beam of electrons is observed by 3D measurements of the IES instrument of the RAPID unit. Observations are verified using a theoretical model showing the build-up of a MTSI under the given circumstances.     

Latitudinal variation of the topside electron temperature at different levels of solar activity

A database of electron temperature (T_e) measurements comprising of most of the available satellite measurements in the topside ionosphere is used for studying the solar activity variations of the electron temperature T_e at different latitudes, altitudes, local times and seasons. The T_e data are grouped into three levels of solar activity (low, medium, high) at four altitude ranges, for day and night, and for equinox and solstices. We find that in general T_e changes with solar activity are small and comparable in magnitude with seasonal changes but much smaller than the changes with altitude, latitude, and from day to night. In all cases, except at low altitude during daytime, T_e increases with increasing solar activity. But this increase is not linear as assumed in most empirical T_e models but requires at least a parabolic approximation. At 550 km during daytime negative as well as positive correlation is found with solar activity. Our global data base allows to quantify the latitude range and seasonal conditions for which these correlations occur. A negative correlation with solar activity is found in the invdip latitude range from 20 to 55 degrees during equinox and from 20 degrees onward during winter. In the low latitude (20 to −20 degrees invdip) F-region there is almost no change with solar activity during solstice and a positive correlation during equinox. A positive correlation is also observed during summer from 30 degrees onward.     

液体火箭发动机涡轮泵用机械密封温度场及热载变形研究

基于ANSYS数值计算软件,建立了液体火箭发动机涡轮泵用机械密封的二维稳态传热模型,依靠经验公式确定了模型的对流换热系数。计算了密封环的温度场和热载变形,分析了密封端面比压、回流流量以及不同材质对密封温度场的影响规律。结果表明:密封端面最高温度发生在靠近密封环内径处,且密封端面比压越大密封环温度梯度越大;密封环热载变形呈收敛间隙,最大变形发生在动环端面的外径处,其值约为2.2μm;密封环端面最高温度随回流流量增加而减小,当回流流量从0.1~0.6 kg/s变化时,密封环端面最高温度可降低18%(从100℃降至82℃);当回流流量增大到0.3 kg/s时,继续提高对密封环端面温升的控制不再显著;采用高导热系数的摩擦副材料能够显著降低端面温升和温度梯度,提高密封工作可靠性。     

带集中热源的散热器温度场的数值分析

随着大规模集成电路的发展,电子设备的封装体积越来越小,功率却越来越大,这就使电子设备的温度日益增高,而电子设备的可靠性又与温度密切相关,良好的散热是电子设备应用中重要的一环.本文以通用的矩形翅片式散热器来对比带集中热源和带平均热源的散热器的温度差异,提出以嵌入热管的方法来解决带集中热源散热器的散热难题,并运用IcEPEK软件对其可行性进行了验证.     

低压断路器灭弧室温度检测

设计了基于光纤光栅传感系统的低压断路器灭弧室温度检测装置,实验测量出灭弧室温度数据,进行了数据的有限元分析,绘制出灭弧室内温度场分布图.     

金属间化合物TiAl(W,Si)合金的蠕变行为和机制

 研究了 Ti-47Al-2 W-0.5 Si合金在 650～ 750℃区间的蠕变行为和变形机制。结果表明,合金 650℃蠕变寿命与施加应力之间符合线性的双对数关系,可用表达式 lg^t_f=10 lg^R+30来描述。蠕变寿命与最小蠕变速率之间满足 Monkman-Grant关系的修正式。合金的比蠕变强度与抗热腐蚀镍基高温合金 K438G相当。在700℃变载荷下蠕变时具有与恒载荷下蠕变相类似的特征。 800℃长期时效粗化合金组织,降低蠕变寿命。位错滑移和形变孪生是合金蠕变的主要变形机制。