研究用现场数据估计系统可靠性参数置信区间

研究用元部件现场信息估计系统可靠性参数,如系统可靠度、可靠寿命等区间估计问题。文中提出了一种新的估计方法——替换百分点法,并运用Monte Carlo数字仿真对估计的置信度和精度进行了分析,研究结果表明此方法具有工程应用价值。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

一种温度动态调节方法及其动态性能仿真研究

航空气源模拟试验台主要用于模拟不同飞行状态时发动机给空气管理系统的供气,由于飞机爬升、降落时发动机供气参数会急剧变化,因此航空气源模拟试验台需具备动态能力.基于一种温度动态调节方法,在合理简化的基础之上采用NHT方法对其温度动态性能进行了仿真研究,仿真结果表明该温度动态调节方法能够满足温度动态性能需求,对动态航空气源模拟试验台的设计选型有较高的参考价值.     

Geometric calibration of Colour and Stereo Surface Imaging System of ESA’s Trace Gas Orbiter

There are many geometric calibration methods for “standard” cameras. These methods, however, cannot be used for the calibration of telescopes with large focal lengths and complex off-axis optics. Moreover, specialized calibration methods for the telescopes are scarce in literature. We describe the calibration method that we developed for the Colour and Stereo Surface Imaging System (CaSSIS) telescope, on board of the ExoMars Trace Gas Orbiter (TGO). Although our method is described in the context of CaSSIS, with camera-specific experiments, it is general and can be applied to other telescopes. We further encourage re-use of the proposed method by making our calibration code and data available on-line.     

Spectroscopy peculiarities of thermal plasma of electric arc discharge between electrodes with Zn admixtures

Plasma of the free burning electric arc between Ag–SnO₂–ZnO composite electrodes as well as brass electrodes were investigated. The plasma temperature distributions were obtained by Boltzmann plot method involving Cu I, Ag I or Zn I spectral line emissions. The electron density distributions were obtained from the width and from absolute intensity of spectral lines. The laser absorption spectroscopy was used for measurement of copper atom concentration in plasma. Plasma equilibrium composition was calculated using two independent groups of experimental values (temperature and copper atom concentration, temperature and electron density). It was found that plasma of the free burning electric arc between brass electrodes is in local thermodynamical equilibrium. The experimental verification of the spectroscopic data of Zn I spectral lines was carried out.     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

野战环境下大型飞机超低空气动特性分析

针对野战环境下的大型飞机超低空飞行,采用CFD方法对地面存在前向或横向不对称障碍物时地面效应对气动参数的影响进行了数值分析,包括纵向稳定性和侧向摇晃等问题.研究结果表明,野战等非常规飞行条件下,地面不确定障碍物会造成大型飞机稳定性变差,严重时可能出现纵向点头和横侧向摇晃现象,容易导致触地危险.最后,从现代飞行控制理论角度提出了对常规布局大型飞机进行闭环控制的研究思路.     

复合材料构件热压罐成型温度场研究

在热压罐固化工艺的热历程中,复合材料零件表面温度场分布的合理与否将直接决定产品的固化质量.以工字型零件和T型加筋壁板两种复合材料零件为研究对象,使用EC-3×8M和SCH-5.5×21M两种型号热压罐,同时选择炉温偶和零件偶两种控温方式对零件进行固化.通过分析温度场测试结果发现,控温方式、设备加热方式、升降温速率、热电偶的摆放位置、固化压力等因素均对零件的温度场有影响.     

TC4钛合金静止轴肩和传统搅拌摩擦焊的温度场对比

基于有限元软件ABAQUS对6mm厚的TC4钛合金传统及静止轴肩搅拌摩擦焊温度场进行了有限元模拟.结果表明,对比传统搅拌摩擦焊接,静止轴肩搅拌摩擦焊接具有较小的高温区,前进方向上具有较大的温度梯度,厚度方向上呈现柱状椭球形分布,上、下表面温度峰值差异较小,具有重叠性较好的热循环曲线.