并行工程及其在航空电子产品研制中的应用

 概述了并行工程的运行特性,介绍了并行工程在空管应答机研制中的应用并分析了在缩短开发周期、提高产品质量、降低研制成本和改进售后服务方面的成效,总结了应用推广并行工程的经验与体会。     

含硝胺推进剂的弹道调节剂的研究前景

添加硝胺类化合物是高能推行剂重要研究技术途径之一,最新推崇的NEPE推进剂也属此列.凡添加硝胺化合物后各类推进剂压力指数均普遍提高和燃速调节也难以实现.预估主要原因出自硝胺化合物的本性,从而导衍出研制这类调节剂几种可能的原则性方向.     

用非线性模型分析气动液阀的启动特性

对气动液阀的启动过程建立了非线性数学模型,分析了尺寸参数和推进剂进、出口压力对该阀的启动特性的影响。计算结果表明：在保证必要的工作寿命的前提下,适当地增大控制腔气孔的直径或增大靠近控制腔的活塞端面直径,降低推进剂进口和出口的压力有利于提高该阀的响应能力。     

三维瞬态导热温度场边界元计算及一阶数学奇异的处理

推导了三维瞬态导热温度场边界元解法的积分方程和离散代数方程，并编制了相应的计算机程序，采用坐标变换的解析消去法，处理边界元的一阶数学奇异点，从而提高了算法的数值精度。用本程序计算了正方体和圆柱环瞬态导热温度场，数值解与解析解的吻合程度令人满意。     

基于支持向量机的组合分类方法及应用

为了解决采用神经网络、决策树作为弱分类器的AdaBoost组合分类存在的不足,进一步改善组合分类效果,提出采用支持向量机(SVM)作为弱分类器的一种新的组合分类诊断方法——AdaBoost-SVM。该方法没有采用一个固定的SVM的核参数,而是自适应调整SVM中的核参数,从而得到一组有效的SVM弱分类器。通过对基准数据库的测试及航空发动机故障样本的诊断,结果表明,所提AdaBoost-SVM方法较好地解决了现有的Ada-Boost组合分类方法中存在的弱分类器本身参数选取困难问题及训练轮数的合理选取问题,并具有更好的泛化性能,更适合对分散程度较大、聚类性较差的航空发动机故障样本进行分类。     

美国航空预研计划及其管理

首先根据世界航空工业发展形势，以美国近期的十二项典型重大航空预研计划为例，叙述其预研计划所包括的内容及执行效果，最后，透过所述的预研计划，分析了美国航空预研计划及其管理的特点，并对我国航空技术预研工作提出几点建议。     

基于齿数的渐开线直齿轮参数化建模

介绍了在UG环境下渐开线直齿轮参数化建模的方法,分析了不同齿数范围对建模过程的影响,并依据分析结果建立了渐开线直齿轮的两个精确模型,利用这两个模型通过修改参数列表能快捷得到满足任意参数要求的渐开线直齿轮的三维模型。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr05Ba0.5-xBixTiO3 （BST） thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influeoces of bismuth （Bi） on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 （BST） thin films. The microstructures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi^3＋ doping ration in BST will lead to decrease of the grain size. It is found that Bi^3＋ doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi^3＋-doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem- perature decreases gradually with the Bi^3＋ contents increasing.     

民用客机舒适性评估

本文给出了能用于说明民用客机旅客乘坐品质的数量关系,这些关系能用于预测旅客乘坐的舒适性。可供设计及使用单位参考。