GPS授时校频方法研究与试验结果

为了解决多目标综合测量系统各测站之间时间同步和频率校准问题,提出了利用GPS(Global Positioning System)单星或多星共视方法进行站间时间同步与校频,给出了这两种方法的计算公式,分析了星历误差、星钟误差、电离层折射误差、对流层折射误差、多径效应和接收机硬件延迟对时间同步精度的影响.为了验证GPS授时校频精度,进行了相关试验.通过与铯原子钟比对,表明利用GPS可实现纳秒级时间同步,校频精度也优于5.0×10-11,多星共视具有更高的同步校频精度.      

民用飞机风挡防冰性能评估

民用飞机适航条款要求在结冰条件下应确保风挡外表面不能结冰,防止影响飞行员视界。因此应确保结冰条件下风挡具有足够的加热功率使其外表面温度高于冰点。根据防冰传热传质机理,利用CFD和Matlab相结合的方法建立了三维风挡热性能分析模型,对某型民用飞机风挡防冰性能进行评估。具体包括防冰热载荷确定、表面温度评估和关键参数校核三部分,并给出了典型飞行工况下风挡防冰热性能评估算例。     

面向大型承载结构强度性能的试验系统高精度装配调控方法

以直径0.6 m开口筒壳为例,分析了装配误差对仿真结果产生的影响,表明高精度量化试验系统装配方法研究的必要性。传统装配方法采用直尺等机械工具开展试验系统装配,导致实际装配误差较大且难以精准定量。因此提出一种试验系统装配误差精准测量与调控方法,该方法通过测量标识点获取装配件实际位置,并计算实际与理论位置的装配误差,结合机械推动以及位移测量等设备实现位置精确调控。为验证方法的可行性与精度,基于自研的强度试验高精度装配软件,分别开展了直径0.6 m和1.6 m圆柱筒壳装配调控试验。相比传统方法,最大位移误差从15.00 mm降至0.75 mm,最大角度误差从0.93°降至0.04°,数值分析承载力误差从1.67%降到了0.04%,降低了装配误差对承载力的影响,提高了试验系统装配精度。     

Minimum sliding mode error feedback control for fault tolerant small satellite attitude control

This paper proposes a new control strategy (which we call “minimum sliding mode error feedback control, MSMEFC”) for small satellite attitude control. As we know, the attitude control algorithm plays a significant role in the whole performance of the satellite, especially under the existence of uncertain disturbances from the space. Without loss of generality, the MSMEFC is presented based on the sliding mode theory. It is assumed that the equivalent control error is defined to offset the uncertain disturbances to improve the control performance. Hence, in order to estimate the optimal equivalent control error, a cost function is derived on the basis of the principle of minimum sliding mode error. Then, the equivalent control error wills feedback to the conventional sliding mode control to obtain the final MSMEFC. According to the theoretical analyzes, the sliding mode after the MSMEFC will approximate to the ideal sliding mode, resulting in enhancing the control performance. Moreover, an adaptive non-singular terminal sliding mode is employed to compare with the performance of MSMEFC. Several simulations are performed to verify the effectiveness of proposed MSMEFC in the presence of serious perturbations, even in some fault-tolerant scenarios.     

系留气球囊体外形优化研究

利用基于约束的Kanikdale修正算法,以及一套用于确定尾翼尺寸和系留缆绳外形的方法,并借助基于GA的GADO优化器,对系留气球囊体形状进行了优化研究。结果表明,通过多材料组合方式生成的囊体,其有效载重能力能够提升6.5%左右。     

基于共轭次梯度算法的磁传感器安装误差校正

随着头盔显示技术的发展,对头盔电磁定位的精度要求越来越高,在现有的加工工艺和机上安装条件下,要提高定位精度,必须对传感器安装误差进行校正。通过坐标转换原理对安装误差进行建模,在此基础上利用最小二乘原则选取目标函数,将校正过程抽象为最优化问题求解。提出一种基于共轭次梯度算法的最优化问题求解方法,实现了传感器安装误差校正。利用MATLAB上对校正算法进行仿真,仿真结果表明,共轭次梯度算法简洁易用、校正精度高、收敛速度快,能够明显提高磁场测量精度。     

基于功率裕度的某型发动机全寿命性能研究

随着使用时间不断增加,研究飞行队所有选装ARRIEL2S系列发动机全寿命性能变化趋势的必要性突显.针对SRRIEL2S系列发动机全寿命性能参数变化特点,提出使用基于可几误差舍弃理论处理发动机功率校验数据,分区间描绘该系发动机全寿命性能指标变化趋势,给出该系发动机全寿命性能特点,为机务工程人员监控该系发动机提供有利依据；提出延长功率校验间隔的假设,并在理论上做了充分论证,为节约该系发动机运行成本提供一个明确及可行的方向.     

空心长轴深孔加工工艺研究

以某发动机空心长轴零件深孔加工为研究对象,设计了长径比为15,长度超过1米的整体硬质合金刀杆,在某加工项目试验中,应用这种超长整体硬质合金刀杆,在细长比大于10的空心长轴的深孔镗削加工中,改变了传统的深孔加工工艺,满足了空心长轴深孔加工中严格的壁厚差要求,取得了明显的效果.     

Effect of surface roughness on microwave brightness temperature from lunar surface: Numerical analysis with a hybrid method

A hybrid method, combining the radiative transfer theory and the method of moments (MoM), is proposed to study the potential effect of the lunar surface roughness on the microwave brightness temperature. The total upward emission reaching the lunar surface from below media is calculated by the radiative transfer theory, and then the brightness temperature is obtained by weighting the bidirectional transmission coefficients which is computed using the MoM. The method is validated by both flat and rough surface models with analytic solutions. With the hybrid method, brightness temperatures from simulated lunar model are calculated and compared to those from a flat layered model. The comparisons show that the effect of rough surface on brightness temperature cannot be ignored and also depends on many other factors, such as observation angle and polarizations. For vertical polarization, an optimal observation angle may exist to reduce the effect of surface roughness. These results indicate that the knowledge of lunar surface roughness is important in microwave remote sensing to the Moon and may probably provide a guide to lunar projects in future.     

低雷诺数下高负荷轴流压气机表面粗糙度流动调控机制

以某1.5级高负荷轴流压气机为研究对象,采用经过校核的数值模拟手段详细探究了低雷诺数下表面粗糙度对其气动性能及内部流场的影响.结果表明:相比于光滑叶片,表面粗糙度为137.8时压气机性能提升最为明显,总压比、堵塞流量以及峰值效率分别提升4.01％、2.24％、5.34％.在整个表面粗糙度大小范围内,表面粗糙度布置在吸力...