多跑道内水平障碍物限制面边界确定方法

对机场多跑道系统的障碍物限制面——内水平面的边界确定方法进行了系统研究。通过将N条（N≥3）复杂构形跑道简化为2N个点集，根据国际民航组织内水平面障碍物限制面形成原理并利用多边形凹凸性几何特征，给出了内水平面边界的确定方法和计算步骤。     

用大面积源检定核应急机载/车载伽玛能谱仪

人工核素大面积源标准是核工业航测遥感中心等单位经过十余年研究建立的新型计量保障标准,使用该标准,可对监测核应急伽玛辐射环境的机载/车载伽玛能谱仪进行检定.使用大面积源标准检定,可以有效地弥补因机载/车载伽玛能谱仪系统的角响应影响因素复杂而难于模拟计算的缺陷,为监测核应急伽玛辐射环境的机载/车载伽玛能谱仪提供了量值传递的保障.本文介绍了大面积源检定的原理和技术方法.     

A theoretical model of semi-elliptic surface crack growth

A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman–Raju formula is developed. The crack is regarded as a sharp notch with a small curvature radius and the process zone is assumed to be the size of cyclic plastic zone. The modified Hutchinson, Rice and Rosengren(HRR) formulations are used in the presented study. Assuming that the shape of surface crack front is controlled by two critical points: the deepest point and the surface point.The theoretical model is applied to semi-elliptic surface cracked Al 7075-T6 alloy plate under cyclic loading, and five different initial crack shapes are discussed in present study. Good agreement between experimental and theoretical results is obtained.     

Analysis of crack opening stresses for center- and edge-crack tension specimens

Accurate determination of crack opening stress is of central importance to fatigue crack growth analysis and life prediction based on the crack-closure model. This paper studies the crack opening behavior for center- and edge-crack tension specimens. It is found that the crack opening stress is affected by the crack tip element. By taking the crack tip element into account, a modified crack opening stress equation is given for the center-crack tension specimen. Crack surface displace- ment equations for an edge crack in a semi-infinite plate under remote uniform tension and partially distributed pressure are derived by using the weight function method. Based on these displacements, a crack opening stress equation for an edge crack in a semi-infinite plate under uniform tension has been developed. The study shows that the crack opening stress is geometry-dependent, and the weight function method provides an effective and reliable tool to deal with such geometry depen- dence.     

Transient simulation of regression rate on thrust regulation process in hybrid rocket motor

The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.     

Storage life of silicone rubber sealing ring used in solid rocket motor

It is urgent to carry out detailed research on storage performance of rubber sealing ring to get the criterion for its storage life. This paper acquires material ageing regularity by theoretical analysis and experimental confirmation. On this condition, failure mode and failure criterion of typical sealing structure is studied, and the failure mechanism is found. Thus by analyzing the stress distribution, the relationship between ageing state and sealing condition is established. Rationalization proposal is put forward and storage life of sealing ring is evaluated. The research mentionedabove has special reference to the design of sealing structures and can provide reference for prolonging their service life.     

肋角度对气膜冷却特性的影响

在光滑二次流通道的基础上,分析对比了两种带肋通道(135°肋和45°肋)对气膜冷却特性的影响.采用瞬态液晶测试技术获得了气膜孔下游表面传热系数比与气膜冷却效率分布.使用Fluent软件RANS数值方法对相应结构进行了数值模拟,并使用了realizable k-ε湍流模型.光滑二次流通道模型中,气膜孔内流线呈螺旋状分布,导致较大的孔内速度分离与流动损失.冷气射流分成两部分,其中一股形成一对偏斜的对转涡.135°肋结构中,二次流通道上部分的旋转涡为顺时针方向,使得气流易于流入气膜孔,气膜孔内流线呈直线分布.45°肋结构中,二次流通道上部分旋转涡为逆时针方向,增强了气膜孔内旋转涡.45°肋结构中冷气流入气膜孔之后的流动结构与光滑二次流通道结构相似.135°肋结构气膜冷却效率最大而表面传热系数比最低.     

无刷直流电机控制器硬件实时性设计方法

在航空领域,无刷直流电机由于其高效率及低故障率,已逐步取代传统液压作动部件.针对无刷直流电机控制器的硬件实时性设计,介绍了控制器的整体架构、各个模块功能及简单的控制流程和方法,重点讨论了控制器的双处理器交互的实时性设计,给出了优化方法,实验数据表明,优化方法达到了预期效果.     

Performance of a small and low-cost chamber to simulate lunar surface environment

The performance of a small and low-cost metal chamber built to simulate the pressure and temperature conditions of lunar surface was assessed and the results are presented. This chamber is intended for studying the physical properties of lunar surface and subsurface (using soil simulants) and also to validate the technology readiness of certain newly developed payloads planned for future lunar surface missions (Lander/Rover). It is possible to reach down to ∼10⁻⁷ Pa under specific conditions and maintain the temperature of the sample under investigation to lunar day and night temperatures. The designed system has been subjected to various tests to evaluate its performance and suitability for carrying out experiments in a simulated lunar environment.     

Evaluating the feasibility of GPS measurements of SSH on board a ship along the Portuguese West Coast

Aiming to validate coastal altimetry data, an exploratory experiment was carried out, using a survey ship with onboard GPS and motion compensation systems. The ship navigation plan followed a track as coincident as possible with the passage of two altimetry satellites, Envisat and Jason-1, along the Portuguese coast, in June 2007.