弧齿锥齿轮齿面拓扑修形及加工参数计算

为了能够实现对齿面啮合性能的灵活控制,针对弧齿锥齿轮小轮提出一种齿面拓扑修形方法,即借助二阶曲面对齿面偏差拓扑的近似表达,将齿面拓扑修形分解为5个方向:螺旋角修正、压力角修正、齿长曲率修正、齿廓曲率修正及齿面挠率修正,通过改变5个方向的修形系数对小轮齿面拓扑结构进行自由控制。在此基础上,建立齿面偏差与机床加工参数之间的修正数学模型,通过构建敏感性矩阵并采用最小二乘法求解,反求出获得修形齿面的小轮加工参数,以便指导加工。以一对弧齿锥齿轮副为例进行修形啮合分析,仿真结果表明:选取齿长曲率修形系数为0.0001,齿廓曲率修形系数为0.0005,齿面挠率修形系数为0.0003,对齿面进行拓扑修形后传动误差幅值为-25.60″,接触迹线倾斜角度变为54.7°,相比原始结果啮合性能得到改善。滚检接触区与理论仿真结果一致,验证了修形方法的有效性。      

盘式永磁同步电机永磁体涡流损耗研究

由于永磁体中存在涡流损耗,这些损耗会以热量的形式散发出来,使盘式永磁同步电机(DPMSM)内部温度升高。当温度过高时,会引起电机运行性能降低。故针对永磁体涡流损耗进行深入研究,对DPMSM的性能提高及优化设计具有重要意义。利用Maxwell三维电磁场有限元分析软件建立电机有限元模型,在三相正弦电流源驱动下求解电机永磁体电磁场分布;为减小永磁体涡流损耗,对永磁体进行不同方向分割,并对不同方向分割进行仿真对比,得出横向分割为3块效果最佳;在利用电磁屏蔽原理减小涡流损耗时,先对其可靠性进行验证,后利用MATLAB曲线拟合得出屏蔽层厚度的最优值。     

考虑刀具偏心的微铣削加工表面粗糙度预测模型研究

基于微铣削刀具轨迹建立了考虑刀具偏心、最小切削厚度的塑性材料微铣削底面粗糙度的预测模型,预测结果表明粗糙度表面形貌呈锯齿状,刀具偏心会影响表面粗糙度的形貌周期和高度,并进行微铣削加工实验,对粗糙度预测模型进行了验证。采用回归统计方法,建立了脆性材料微铣削加工表面粗糙度预测模型,对加工表面形貌进行观察,利用响应曲面法得到了各铣削用量对表面粗糙度的影响规律。     

仿壁虎刚毛阵列对卫星表面吸附能力模型与计算

壁虎脚的粘着机理对航天机器人脚掌的研制和开发具有重要启发意义.通过单根刚毛与光滑表面黏着力模型与计算、卫星粗糙表面分布模型与接触概率与计算、刚毛阵列与卫星粗糙表面黏着力模型与计算等,分析仿壁虎刚毛阵列对卫星表面的吸附能力,发现在一定条件下仿壁虎刚毛阵能够在太空失重环境中黏着在卫星表面,对航天舱内爬行机器人、管道机器人的...     

载人月球探测月面活动发展设想

载人月球探测是浩大的系统工程,组成复杂,关键技术多,研制周期长,经费投入高,任务风险大.月面活动是载人月球探测任务体现能力、保障安全、提升效益的重要组成部分,必须回答"为什么""去哪里""怎么干"等问题.本文从国内外月球探测历程出发,结合当今世界月球探测领域趋势与局势,从月球战略布局、月球科学内涵开展分析.针对月面驻留...     

Evolution of periodic orbits near the Lagrangian point L2

A study of the evolution of the periodic and the quasi-periodic orbits near the Lagrangian point L₂, which is located to the right of the smaller primary on the line joining the primaries and whose distance from the more massive primary is greater than the distance between the primaries, in the framework of restricted three-body problem for the Sun–Jupiter, Earth–Moon (relatively large mass ratio) and Saturn–Titan (relatively small mass ratio) systems is made. Two families of periodic orbits around the smaller primary are identified using the Poincaré surface of section method – family I (initially elliptical, gradually becomes egg-shaped with the increase in the Jacobi constant C and elongated towards the more massive primary) and family II (initially egg-shaped orbits elongated towards L₂ and gradually becomes elliptical with the increase in C). The family I in the Sun–Jupiter and Saturn–Titan systems contains two separatrix caused by third-order and fourth-order resonances, while the Earth–Moon system has only one separatrix which is caused by third-order resonances. Also in the Sun–Jupiter and the Saturn–Titan systems, family I merge with family II, around Jacobian constant 3.0393 and 3.0163, respectively, while in the Earth–Moon system, family II evolves separately from two different branches. The two branches merge at C = 3.184515. In the Earth–Moon system, the family II contains a separatrix due to third-order resonances which is absent in the other two systems.     

Sliding mode control of reaction flywheel-based brushless DC motor with buck converter

Reaction flywheel is a significant actuator for satellites’ attitude control. To improve output torque and rotational speed accuracy for reaction flywheel, this paper reviews the modeling and control approaches of DC-DC converters and presents an application of the variable structure system theory with associated sliding regimes. Firstly, the topology of reaction flywheel is constructed. The small signal linearization process for a buck converter is illustrated. Then, based on the state averaging models and reaching qualification expressed by the Lee derivative, the general results of the sliding mode control (SMC) are analyzed. The analytical equivalent control laws for reaction flywheel are deduced detailedly by selecting various sliding surfaces at electromotion, energy consumption braking, reverse connection braking stages. Finally, numerical and experimental examples are presented for illustrative purposes. The results demonstrate that favorable agreement is established between the simulations and experiments. The proposed control strategy achieves preferable rotational speed regulation, strong rejection of modest disturbances, and high-precision output torque and rotational speed tracking abilities.     

多孔介质隔热材料中的辐射热传递分析

新型的多孔材料以其重量轻、强度高备受航天工程设计人员的亲睐,尤其是作为隔热材料使用,可以说是航天工程热防护系统的热门材料.多孔介质在辐射热传递方面具有吸收发射和散射的功能,这些功能在其接受外来热流的作用下,于内部达到热能量平衡,求解这一平衡方程就可以求出辐射热流在材料中的分布.由于求解这一方程的困难,许多学者对材料特性...     

提高飞行器升力的若干方法研究

本研究用数值模拟方法研究了四种增升方法。数据模拟的出发方程是可压流的Ｎ－Ｓ方程，格式为Ｂｅａｍ－Ｗａｒｍｉｎｇ格式的改进型。通过上述方法分别研究了：（１）动界效应对提高升力的作用；（２）涡的有利干扰对主升力面的影响；（３）吸气的驻涡增效应；（４）升力面下表面向下喷气的增升作用。研究结果表明，采用上述四种方法可有效地提高飞行器的升力，对改善飞行器的性能有着十分重要的意义。     

光学基片表面软质抛光胶体粒子的激光清洗

介绍了光学基片表面软质抛光胶体粒子激光清洗的基本方法、原理和实验装置,并通过对含有污染微粒的基片表面进行激光清洗,获得了高洁净表面的光学基片.