基于结构方程模型的航空公司顾客满意度研究

简要介绍了结构方程模型的基本原理,根据航空公司运营特点,给出航空公司顾客满意度的测评模型,并以中国国际航空公司顾客满意度的测评为例,进行理论模型的验证与顾客满意度的测评。结构方程模型可以对整个顾客满意度测评指标体系的合理性进行检验并做了系统分析。     

Love Waves in Layered Graded Composite Structures with Imperfectly Bonded Interface

Theoretical analysis and numerical calculations of Love wave propagation in layered graded composites with imperfectly bonded interface are described in this paper. On the basis of WKB method, the approximate analytic solutions for Love waves are obtained. By the interface shear spring model, the dispersion relations for Love waves in layered graded composite structures with rigid, slip, and imperfectly bonded interfaces are given, and the effects of the interface conditions on the phase velocities of Love waves in SiC/Al lay- ered graded composites are discussed. Numerical analysis shows that the phase velocity decreases when the defined flexibility parameter is greater. For the general imperfectly bonded interface, the phase velocity changes in the range of the velocities for the rigid and slip interface conditions.     

楔形底部直升机着水载荷和压力分布的估算方法研究

基于VonKarman和Wagner的水动力冲击理论，忽略冲击过程中浮力和粘性力的影响，将机身简化为V形楔形体，建立简化的刚体运动方程，对其求解得到楔形底部直升机着水载荷和压力分布估算方法。同时，将理论结果与试验数据进行相关性分析，验证了该方法的合理性。此估算方法适用于直升机的设计水线未被浸入的情况，可以用于楔形底部舰载机直升机的水上迫降载荷计算，为机身结构设计提供依据。     

Silver Film Growth on Glass Ceramic by Radio Frequency Magnetron Sputtering

Thin silver films are deposited by radio frequency magnetron sputtering on glass ceramic at room temperature.Variations of sputtering power,bios voltage and power density are carried out for each deposition,then parts of as-deposited samples are subjected to annealing at 600 ℃ within a vacuum chamber.Structural properties are studied by X-ray diffraction(XRD),scanning electron microscope(SEM)and laser scanning confocal microscope(LSCM).It is shown that structural properties have a strong dependency on sputtering power and annealing temperature.Electrical contact resistance measured by a four point probe instrument is directly affected by the thickness of films.It is also found that the film conductivity,especially in thinner films,is improved by the increasing grain size.Finally,the film adhesion is observed by scratch tests.And the adhesive ability deposited by radio frequency magnetron sputtering shows a better performance than that produced by traditional methods.     

Predictive Modeling and Parameter Optimization of Cutting Forces During Orbital Drilling

To optimize cutting control parameters and provide scientific evidence for controlling cutting forces,cutting force modeling and cutting control parameter optimization are researched with one tool adopted to orbital drill holes in aluminum alloy 6061.Firstly,four cutting control parameters(tool rotation speed,tool revolution speed,axial feeding pitch and tool revolution radius)and affecting cutting forces are identified after orbital drilling kinematics analysis.Secondly,hybrid level orthogonal experiment method is utilized in modeling experiment.By nonlinear regression analysis,two quadratic prediction models for axial and radial forces are established,where the above four control parameters are used as input variables.Then,model accuracy and cutting control parameters are analyzed.Upon axial and radial forces models,two optimal combinations of cutting control parameters are obtained for processing a13mm hole,corresponding to the minimum axial force and the radial force respectively.Finally,each optimal combination is applied in verification experiment.The verification experiment results of cutting force are in good agreement with prediction model,which confirms accracy of the research method in practical production.     

基于单参数迭代的TAEM在线轨迹生成方法

针对大升力体轨道再入飞行器末端能量管理（TAEM）段制导控制能力强、末端约束不惟一的问题，将TAEM段分为动压跟踪和着陆预备2个阶段，设计了不同的纵向轨迹剖面，从而将TAEM段在线轨迹生成问题转化为单参数搜索问题。第1阶段设计标称动压剖面为纵向参考轨迹，使得飞行器过程约束得到保证。第2阶段纵向剖面设计为标称高度剖面，从而使得末端点高度和倾角约束得到保证。根据末端动压误差设计修正律，迭代修正第一阶段动压剖面，从而使得最终的纵向轨迹满足所有的状态约束。在线轨迹递推采用以时间为自变量的数值积分，递推过程引入闭环制导律，通过实时修正攻角跟踪纵向剖面，修正倾侧角跟踪地面轨迹，从而保证在线生成的轨迹符合物理特性，降低闭环制导难度。在考虑初期再入末端大范围状态散布情况下，数值仿真显示了所提算法的鲁棒性。     

基于微分进化算法的二自由度PID控制器参数优化

针对二自由度PID控制器参数多、调节困难等问题,提出了一种基于微分进化算法参数调节优化方法。证明了微分进化算法能够收敛到平稳点,并具有概率全局收敛性。研究了二自由度PID控制器参数与抑制特性、跟踪特性的关系,并将微分算法与遗传算法、粒子群算法的参数优化结果进行了比较。仿真验证表明,微分算法能够更好地实现二自由度PID控制器参数的调节,具有优异的跟踪特性和抑制特性。     

影响聚四氟乙烯材料加工表面粗糙度因素的研究

在现代航空发动机的产品中,保护圈、密封件等零件广泛使用聚四氟乙烯材料制造.在加工中多采用车削加工,粗糙度一般为Ra1.6,本文通过选用不同车床、刀具、加工参数的方法,提高该类材料加工后的表面粗糙度,为后续加工提供经验和数据.     

基于功率裕度的某型发动机全寿命性能研究

随着使用时间不断增加,研究飞行队所有选装ARRIEL2S系列发动机全寿命性能变化趋势的必要性突显.针对SRRIEL2S系列发动机全寿命性能参数变化特点,提出使用基于可几误差舍弃理论处理发动机功率校验数据,分区间描绘该系发动机全寿命性能指标变化趋势,给出该系发动机全寿命性能特点,为机务工程人员监控该系发动机提供有利依据；提出延长功率校验间隔的假设,并在理论上做了充分论证,为节约该系发动机运行成本提供一个明确及可行的方向.     

Multi-station observation of ionospheric disturbance of March 9 2012 and comparison with IRI-model

The magnetic storm of 9 March 2012 is a single step intense storm (Dst = −143 nT) whose main phase begins around 0100 UT and lasted for almost 11 h. The increases in NmF2 recorded 33% and 67% incidence respectively during the main and the recovery phase of the storm at the stations considered. The increase in hmF2 occurred concurrently with the increase in thickness parameter B0 between 0000 and 1100 UT, and a simultaneous decrease in the shape parameter B1 for the entire mid-latitude stations. Generally, B1 responded to the storm with a decrease away from the quiet day average, and decreased simultaneously with the increase in NmF2. B0 displays higher variability magnitude during daytime than the nighttime period. The occasional differences in the response of the ionospheric parameters to the storm event are attributed to longitudinal differences. Variation in hmF2 and NmF2 is projected to change in B1, but the rationale behind this effect on B1 is still not known and therefore left open. The two IRI options over-estimate the observed values with that of URSI higher than CCIR. The over-estimation was higher during the nighttime than the daytime for NmF2 response for the mid-latitude stations and the reverse for the equatorial station. A fairer fit of the model with the observed for all parameters over Jicamarca suggests that equatorial regions are better represented on the model. Extensive study of B1 and B0 is recommended to arrive at a better performance of IRI.