圆形隧道衬砌与围岩应力的解析法研究

隧道衬砌与围岩的应力分析是隧道设计中一个重要内容。本文基于厦门市东通道海底隧道对圆形隧道衬砌与围岩应力的封闭解析解法进行研究,首先利用MATLAB编制衬砌与围岩应力程序并选用一个已有精确解的实例进行校验,然后对圆形隧道四种工况进行计算并给出相关的衬砌和围岩的分布曲线,最后对计算结果进行了相关分析。     

TC11钛合金的热态变形行为研究

采用等温恒应变速率压缩试验法,研究了TC11合金在780℃-1080℃和应变速率为0.001s-1~70s-1范围内的高温压缩变形行为。考察了变形温度、应变速率及变形程度对流动应力的影响关系。结果表明,流动应力对变形温度和应变速率敏感,随变形温度升高和应变速率降低流动应力减小,特别是在α β两相区变形温度对流动应力的影响显著。     

Investigation on surface roughness,residual stress and fatigue property of milling in-situ TiB2/7050Al metal matrix composites

For higher efficiency and precision manufacturing, more and more attentions are focused on the surface roughness and residual stress of machined parts to obtain a good fatigue life. At present, the in-situ TiB₂/7050Al metal matrix composites are widely researched due to its attractive properties such as low density, good wear resistance and improved strength. It is of great significance to investigate the machined surface roughness, residual stress and fatigue life for higher efficiency and precision manufacturing of this new kind material. In this study, the surface roughness including two-dimensional and three-dimensional roughness, residual stress and fatigue life of milling in-situ TiB₂/7050Al metal matrix composites were analyzed. It was found from comparative investigation that the three-dimensional surface roughness would be more appropriate to represent the machined surface profile of milling particle reinforced metal matrix composites. The cutting temperature played a great role on the residual stress. However, the effect of increasing cutting force could slow down the transformation from compressive stress to tensile stress under 270 °C. An exponential relationship between three-dimensional roughness and fatigue life was established and the main fracture mechanism was brittle fracture with observation of obvious shellfish veins, river pattern veins and wave shaped veins in fracture surface.     

Flow field characteristics,mixing and emissions performance of a lab-scale rich-quench-lean trapped-vortex combustor utilizing a quench orifice plate combined with a bluff-body

In this study, the low emission combustion technology of Rich-Quench-Lean (RQL) has been applied in Trapped-Vortex Combustor (TVC), and the combinative RQL-TVC shows a promising low emissions performance. By utilizing a quench orifice plate combined with a bluff-body, a lab-scale RQL-TVC was designed. The flow fields of RQL-TVC were measured by 2-D PIV and predicted by 3-D numerical simulation. Flow structures, radial profiles of normalized mean axial velocity, turbulence intensity and mixing level of the quench zone were analyzed. Results reveal that the dual-vortex and the single-vortex flow patterns both exist in cavities and quench zone of RQL-TVC, and the turbulence intensity is strong in the quench zone with some reverse flows. The spiral vortex was discussed by 3-D streamlines and the detail flow structures of the quench zone were analyzed based on the numerical results. The mixing level of the quench zone was determined, and results show that the quench device enhances the mixing level compared with TVC. Combustion efficiency and emissions performance were investigated experimentally, and results demonstrate that RQL-TVC has relatively higher combustion efficiency and lower emission index of CO, UHC and NO_x than the same size lab-scale TVC in present work.     

应力波天平在国内激波风洞上的应用

介绍了应力波天平的特点、原理,通过应力波天平设计、制作、校准、试验、数据处理等方面在中国空气动力研究与发展中心φ0.6m激波风洞上的应用情况,指出有必要在国内激波风洞上更进一步地开展应力波天平测力技术.     

FL-9低速增压风洞主体结构有限元分析与气压试验

FL-9低速增压风洞是"十五"国家批准建设的大型航空基础设施,笔者简要介绍了该风洞基于有限元方法的应力、变形和模态分析,并与风洞气压试验结果进行了对比.结果表明:有限元计算中所采用的单元类型、模型简化、边界约束等处理方法合理可行,应力计算值与实测值比较一致,最大薄膜应力为147.6MPa,低于许用值42.1%,风洞结构具有较大的安全裕度.风洞的前六阶模态分析为风洞安全运行提供了参考依据.     

定常基线卫星编队构形设计

采用动力学法研究了卫星编队的相对运动特性,根据星间相对基线的定义,仔细推导了星间相对基线与卫星编队构形参数之间的关系,并根据此关系定义了一种可以较好地反映星间相对基线运动稳定性的指标,即稳定度.在一个轨道周期内,分析了三种特殊卫星编队的最大水平基线和最大垂直基线在相同稳定度下的稳定时间.结果表明,这三种编队构形不能满足水平基线和垂直基线同时定常的要求.由此出发,重点研究了可以使星间相对基线定常的条件,并得出了相应的结论.水平基线定常的充要条件为三个约束关系式,垂直基线定常的充要条件为两个约束关系式.由此条件同时可知,两星编队无法满足水平基线和垂直基线同时定常的要求,因此,至少需要三星编队才可以达到此要求.最后,按照本文所得结论,设计了一个水平基线和垂直基线同时定常的三星编队.利用成熟软件对设计结果进行了分析,分析结果表明了本设计方法的正确性.      

固体火箭发动机药柱表面裂纹分析

为了分析含表面裂纹的固体火箭发动机药柱在温度、燃气内压与轴向过载联合作用下的扩展情况,在固体火箭发动机的危险截面上沿危险方向预设表面裂纹。采用有限元方法,在裂纹尖端构建三维奇异裂纹元,模拟裂纹扩展,分别计算随着裂纹扩展所对应裂纹深度的应力强度因子,得到了应力强度因子随裂纹深度的变化规律。根据应力强度因子的变化规律,探讨了发动机药柱裂纹扩展的趋势。     

喷丸强化对AISI 420不锈钢固体粒子冲蚀行为的影响

研究了喷丸强化(SP)对AISI 420马氏体不锈钢抗同体粒子冲蚀(SPE)行为的影响.探讨了喷丸引起的表面残余压应力,表面粗糙度增大和表面加工硬化等三因素对SPE抗力的作用机制.结果表明:SP处理对AISI 420不锈钢在30°攻角下的SPE抗力无明显影响,但却降低了该钢在90°攻角下的SPE抗力.SP处理后进行表面抛光,则使该钢在两种攻角下的SPE抗力均得以提高.SP三因素对SPE抗力的作用机制主要有:表面粗糙化增大了试样表面对冲蚀粒子的有效暴露面积,因而降低了不锈钢在两种攻角下的SPE抗力;表面残余压应力能够有效抑制疲劳裂纹萌生和早期扩展,因而能有效提高AISI 420不锈钢的SPE抗力,特别是对90°垂直冲击条件下SPE抗力的提高作用更为明显;表面加工硬化提高了材料表面的微犁削抗力,因而对提高AISI 420钢在30°攻角下的SPE抗力有贡献,但是表面加工硬化层的抗多冲疲劳性能差,却不利于AISI 420钢在90°攻角下抗SPE性能的改善.     

复合材料层板固化全过程残余应变/应力的数值模拟

采用商业软件对带有铝板的复合材料层板固化全过程残余应变/应力进行数值模拟计算。在固化过程的模拟中,应用有限元法计算复合材料层板热-化学模型,有限差分法计算固化动力学模型,通过设置较小的时间步实现求解两个模型强耦合的关系。在残余应力数值模拟中,化学收缩引起的应变在每一计算步以初始应变施加在复合材料结构上。基于以上技术,对带有铝合金的复合材料层板固化全过程残余应变/应力演化进行数值模拟,并分析纤维方向和垂直纤维方向复合材料的残余应变/应力演化历程。通过与试验中层板曲率的比较,验证文中模型计算的准确性。