具有叶顶间隙涡轮转子叶栅流动的拓扑及旋涡结构观测

为了了解具有顶部间隙的涡轮转子叶栅流道内及间隙内的流动状况,采用五孔球头测针和五孔微型束状测针分别对叶栅流道和间隙进行了测量,同时对端壁及叶片壁面进行了流动显示,采用拓扑分析方法对显示结果进行了详细分析,探讨了间隙存在时叶栅各种旋涡的形成机理。测量及显示结果表明：由于顶部间隙的存在,在叶栅顶部形成如泄漏涡等复杂的涡系结构,这些涡系之间及它们与上通道涡之间发生强烈的相互作用,明显增大了叶栅的顶部损失;在叶栅尾缘附近存在着部分回流区域。     

细长体截面流态拓扑结构演化及其稳定性分析

应用动力系统的稳定性理论,分析了细长体在不同迎角下截面绕流拓扑结构的演化和稳定性.指出旋成体背涡的发展,导致截面流场拓扑结构变化,而由稳定对称旋涡流态变成不稳定对称旋涡流态,进而再在小扰动下变成稳定非对称旋涡流态是导致旋成体非对称背涡出现的基本历程.      

背风涡隔离对大攻角旋成体表面压力分布的影响

通过在背风母线处沿纵向对称面嵌入隔离板，观测了大攻角旋成体在这种背风涡被隔离状态下的表面压力分布情况。隔离板的作用旨在削弱、隔阻两侧背风涡间的相互联系和诱导，以便考察背风涡诱导作用对物面流动的影响。不同隔离（包括无隔离情况）状态下的实验结果表明，背风涡的隔离对表面压力分布有不同程度的影响，故这一研究和结果可供探讨大攻角流动非对称性成因作参考。     

Experimental and computational investigation of hybrid formation flight for aerodynamic gain at transonic speed

The influence of the wing-tip vortex of leading aircraft on energy savings, quantified by formation aerodynamic force fraction of the following aircraft, is studied at transonic speed for a matrix of leading aircraft’s vortex locations. The research model adopts the hybrid formation of medium and large aircraft. The leading aircraft is scaled by 2.1%, and the following aircraft is scaled by 1.4%. An aerodynamic benefit “map” is developed to determine the optimum location of the following aircraft relative to the leading aircraft wake and to compare with experimental results, thus validating the use of CFD for the formation flight at cruising speed. The response surface model of aerodynamic gain effect relative to formation parameters is established via numerical calculation and wind tunnel test. The optimal formation parameters and the setting criteria of the study model are optimized. Results show that the wing-tip vortex of large aircraft significantly increases lift and reduces drag on the medium-sized aircraft following it. Reduced drag slightly increases with the flow direction position. With the increase of flow direction distance, the peak area moves from 15% of wing-tip overlap to 20% of overlap. In addition, the maximum drag decreases about 16%, and the maximum lift increases about 12%. The lift drag ratio of the optimal position is increased by 27%, which is twice as large as that of the same scale ratio aircraft formation. Results show that the increase of lift is mainly caused by the increase of suction peak and suction range.     

Bump进气道中鼓包诱导的激波/边界层干扰特性

为了探索Bump进气道中鼓包诱导的锥形激波和机身发展而来的湍流边界层干扰问题,分析其气动优势,首先选取了半锥和半棱锥这两种与鼓包的流场结构具有一定相似性的构型作为参照,采用数值仿真方法,分别对这三类典型的三维激波/湍流边界层干扰问题进行了流场分析。在此基础之上,设计了三个不同马赫数的鼓包,并研究了设计马赫数对鼓包流场特性的影响。结果表明:当三类构型的无黏激波强度相等时,半锥诱导产生的旋涡强度最强,鼓包次之,半棱锥最弱。尽管鼓包诱导的流场非常复杂,其干扰流场却呈现出准锥形相似的特性。虽然半锥对边界层的排移能力最强,但是综合考虑边界层排移能力及进气道出口流场畸变下,鼓包最具优势,这也是其被选为超声速进气道前缘压缩面的重要原因之一。此外,在设计状态下,适当增加设计马赫数能改善鼓包排移边界层的能力,但设计马赫数太高,边界层排移能力基本不变,反而使得进气道总压损失急剧增加。      

Taylor-Couette流的DSMC数值模拟

使用圆柱坐标系网格的三维DSMC(Direct Simulation Monte Carlo)模型,对同轴圆柱间Taylor-Couette流中Taylor涡的形成进行了数值模拟,并分析了不同计算域和边界条件下稳定流场中Taylor涡的轴向排列结构.在网格设置和流场参数不变的情况下,使用轴对称DSMC模型对Taylor涡进行数值模拟,所得Taylor涡的稳定过程与三维结果一致,验证了使用三维DSMC方法来解决微尺度低速的稀薄气流问题的可行性.三维模拟结果表明Taylor涡以较大的圆周速度绕轴旋转,二维模拟则无法体现.对不同的内圆柱旋转速度进行数值模拟,确定了能够产生Taylor涡的临界速度值.     

国内主力低速风洞大迎角实验的不确定度水平研究

笔者将AGARD-AR-304不确定度评估方法推广到大迎角领域,给出计算低速风洞大(小)迎角实验不确定度的工程方法.相应的计算软件已成功地用于国内主力低速风洞实验的不确定度评估,完成了5座风洞8个模型大迎角实验的不确定度评估,给出了我国主力低速风洞大(小)迎角实验的不确定度水平.