跨声速风洞斜孔壁非线性流动试验

为分析跨声速风洞斜孔壁近壁区域的流动特性，评估气流偏角-压力系数的非线性关联，在0.6 m跨超声速风洞中开展了基于七孔探针的流动特性测量试验。通过气流偏角和压力系数分布分析了斜孔壁流动的差阻特性，以及马赫数、模型升力对斜孔壁流动的影响，最后基于试验结果发展了计算斜孔壁特性参数的微分法，并与经验方法结果进行对比。结果表明，斜孔壁流动呈现出明显的差阻性和非线性，在负压差范围内，近壁流动仍以出流为主；高亚声速时，空风洞模型区孔壁流动特性趋于实壁；安装模型后，随着升力的增大，升力面对应的孔壁区域流动向入流发展，孔壁流动特性趋于开口边界。     

A systematic approach to nonlinear rotorcraft model identification

The development of a powerful parameter estimation routine and its integration into the simulation environment HOST is described. With this tool approaches are being made towards new strategies of mathematical modeling, aimed at providing highly accurate and nevertheless run-time efficient simulation models. The identification routine is capable of optimizing parameterized models in both dynamic time domain simulation and static (e.g. trim state variation) conditions. Examples of both cases are presented to emphasize the improvement in the system response prediction and to demonstrate the abilities of the identification techniques in combination with the nonlinear simulation platform. This article reviews the activities and achievements accomplished by the DLR Institute of Flight Research and the ONERA Systems Control and Flight Dynamics Department during the last few years in the research on rotorcraft flight dynamics modeling and model identification. Future activities that require extensive high fidelity modeling are in the scope of the current and coming modeling activities that include the use of the presented methods and software technologies.     

3-D position estimation of isolated target and optimal trajectory choice in parasitic synthetic aperture radar

Bistatic SAR (BSAR) systems have recently been the subject of several studies, but little attention has been given to the potential of the location of targets. In the paper, the performance of the estimation of 3-D position of a target (TPE) in parasitic SAR is obtained analytically and illustrated by computer simulation using ambiguity function analysis, and the maximum likelihood estimate (MLE) approach. It was shown that by using a multi look parasitic BSAR all three coordinates of an isolated point target (IPT) could be evaluated. Analytical closed form equations that characterize the measurement accuracy were derived. In the final these equations will be used to demonstrate various cases of more practical, including optimal trajectories choice under any geometry configuration case, moreover, the conclusion is verified via Matlab.     

基于偏最小二乘回归分析的装备研制费用估算方法及应用

介绍了寿命周期费用的概念以及各阶段分布情况;针对经典回归分析的不足,采用偏最小二乘回归分析对某装备样本数据进行分析建模;建立了研制费用与几个相关指标的回归方程,并将估算结果与经典的回归分析进行对比,验证模型的合理性。该模型能较好地反映了费用与各指标之间的关系,对后续寿命周期费用的分析与控制有一定的意义。     

高精密小电阻测量方法及测量结果的不确定度评定

在高精密小电阻的测量过程中，由于接触电阻、测量线电阻及测量条件等都会对其测量结果产生不可忽视的影响，因此，选择合适的测量方法对提高测量结果的置信度尤为重要。本文着重介绍了用恒流源和数字电压表间接测量高精密小电阻的具体方法，对其测量结果的不确定度进行了分析与评定。     

高值电阻国际比对的方法研究

介绍了参加亚太实验室认可合作组织(APLAC)开展的高阻1 MΩ;10 MΩ实验间比对的方法,对一种用参考电压测量高阻的方法进行了描述,解决了其中的技术问题,对测量不确定度进行了分析,其结果为测量1MΩ的合成标准不确定度为3.10-6,测量10 MΩ的合成标准不确定度为5.10-6,APLAC公布的比对中期报告证明了该方法的可靠性。     

一般概率测度的核估计

在测度弱收敛的意义下，研究了一般概率测度μ的核估计μn，得到了它的渐近无偏性、强相合性及在给定条件下的收敛速度。     

侧链基团和填料对硅橡胶材料耐烧蚀性能的影响

为了研究侧链基团和填料对硅橡胶材料耐烧蚀性能的影响,选用具有苯环和多面体低聚倍半硅氧烷(POSS)这2种侧链基团的硅橡胶基体,以及Mg(OH)2、蒙脱石、Fe2O3和短切碳纤维(1 mm)这4种填料,利用马弗炉等温烧蚀和动态热失重TG法研究不同侧链基团和填料样品的耐烧蚀机制。结果表明:苯环和POSS基团的引入使得基体初始分解温度分别提高了79 ºC和9 ºC,质量损失率分别降低了19.4%和12.0%。以Mg(OH)2 25 g(每100 g硅橡胶)、蒙脱石4 g和Fe2O3 6 g作为硅橡胶复合材料进行填料时,其质量烧蚀率为0.008 g/s,相比纯橡胶基体降低了86.8%。在以上配方中继续引入5 g碳纤维,使其质量烧蚀率降低至0.004 g/s。残炭层的微观形貌显示,短切碳纤维形成的三维骨架结构是提高硅橡胶材料耐烧蚀性能的关键。     

基于卫星观测数据的弹道导弹初始状态估计

利用卫星探测数据对大气层外飞行的弹道导弹弹道进行估计。在极大似然估计中,由于卫星探测导弹运动的可观测性较差,使初始点估计变得十分病态,传统的Gauss Newton迭代算法不再适用,而采用较为复杂Levenberg Marquardt算法,分别对单颗卫星和两颗卫星的情况进行了Monte Carlo仿真,得到了各自的归一化残差测量误差(代价函数),结果表明该算法有效。     

化学气相反应法在C/C复合材料抗氧化处理中的应用

通过把硅蒸气渗入预制体孔隙与碳直接反应生成SiC的化学气相反应(CVR)方法,提高初始密度和预制体结构均不同的C／C复合材料的抗氧化能力,研究了C／C复合材料的密度变化与微观结构,并对其进行了氧化试验。结果表明,因CVR温度、C／C复合材料初始密度不同,抗氧化处理后的密度增加量有显著不同。针刺炭布C／C／SiC复合材料在马福炉中于1160℃经65min氧化后,其失重率仅2．6％,而密度为1．95g／cm^3的同结构C／C复合材料相在同条件下失重率高达32％。