基于行波与模态的混合方法对Timoshenko梁进行振动主动控制

 基于Timoshenko梁理论,采用波控制和独立模态空间混合方法,对悬臂梁的振动控制问题进行研究。采用波控制方法实现对Timoshenko梁结构的一点或多点的横向位移的振动控制。首先,基于结构的整体运动,采用模态坐标控制方法,对结构振动进行整体控制设计。而后,基于结构的局部性质,采用波方法吸收结构振动中的高频能量并求出Timoshenko梁中波的反射因数和透射因数。理论上研究了单位力扰动下的悬臂梁的振动。考虑的具体方法是将PD反馈波控制与基于极点配置法设计的模态控制相结合。最后给出数值结果。     

高性能的标准单元库设计

从仿真和流片两个方面对标准单元库的验证方法进行了研究.在仿真方面,提出了采用静态时序分析工具和SPICE仿真工具对单元的估算值和仿真结果进行比较分析的方法来验证,同时还给出了具体的操作步骤实例.在流片验证中,提出了一种非常有效的电路结构.这种电路结构不但能够准确验证时序,还能极大地减少PAD数量;最重要的特点是:该电路能够完全避免PAD和非被测单元的引入带来的额外延迟,从而得到准确的被测单元延迟.     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

New Cutting Force Modeling Approach for Flat End Mill

A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

阻力伞附加质量与阻力系数修正方法

在阻力伞试验,特别是高速滑车试验过程中,由于阻力伞系统作非匀加速的非定常运动以及前置体尾流场的影响,现有的阻力伞试验数据计算方法已经难以准确计算其阻力系数.本文针对阻力伞试验过程中的这种非定常运动和尾流干扰特性,对阻力伞系统进行了动力学分析,并对阻力伞非定常运动过程中的附加质量和尾流场特性进行了理论研究,提出了阻力伞双...     

利用红外加热笼进行低热流模拟的设计方法研究

在航天器热平衡试验中,散热面区域的低热流密度要求往往难以实现。在以往的试验中,考虑到加热笼覆盖系数对热流密度均匀性的影响,通常选用红外灯阵作为主要的外热流模拟装置。但是红外灯阵体积和热容较大,形状适应性不强,对试验容器空间要求较高。文章利用仿真的手段研究了加热笼的覆盖系数对热流密度均匀性的影响,探讨了利用红外加热笼进行低热流模拟的可行性。     

熔融沉积成型连续碳纤维增强尼龙蜂窝芯材的压缩特性

采用熔融沉积成型方法成形了连续碳纤维增强尼龙复合材料蜂窝芯材,并对不同测试方向的静态单轴压缩特性进行了表征分析,着重关注不同测试方向熔融沉积成形蜂窝芯材平面静态压缩破碎行为和能量吸收行为,并与纯聚合物基体进行对比。结果表明:X_1方向的压缩平台区域的力-位移曲线更加平滑稳定,且载荷值稍高于X_2方向,因此X_1方向更适用于能量吸收应用;此外,连续纤维的增强作用可使蜂窝芯材的平台载荷值得到明显提升。研究结果为连续纤维增强聚合物复合材料的空间增材制造提供理论基础。     

考虑侧窗约束的模型预测静态规划末制导方法

针对红外导引头侧窗探测模式下,非对称视场约束造成末制导阶段目标易丢失的问题,提出一种考虑侧窗约束的模型预测静态规划末制导方法。首先,基于体视线坐标系建立三维相对运动模型,得到不依赖于“小攻角”假设的准确模型。在处理无过程约束问题的模型预测静态规划方法基础上,引入松弛变量与虚拟控制量,设计出考虑侧窗视场约束的末制导算法。为了进一步降低末制导算法对初始猜测轨迹的依赖性,提高适应性与计算效率,提出逐步增加约束条件的计算策略。仿真结果表明,该方法在末制导过程中满足侧窗约束,相比于凸优化方法,优化变量减少,计算速度更快;相比于基于障碍李雅普诺夫函数的末制导律,能够满足侧窗约束,同时能适应不同的初始条件。     

某型飞机空中受油管自动开锁故障分析

针对某型飞机空中受油管在收上位置钢珠锁自动开锁故障,对空中受油管液压收放系统、电路控制系统、收上位置钢珠锁工作原理进行分析,比对钢珠锁开锁压力理论计算和收放系统回油压力测试试验结果,找出空中受油管收上位置钢珠锁自动开锁原因,提出改进建议。