用光散射效应分析激波管内膨胀率对水蒸气成核与凝结的影响

用多重光散射法对水蒸气在激波管中的自发成核凝结过程进行了实验研究，分析了膨胀率对成核率和凝结过程的影响。根据理论计算和实测数据结果，所得结论是：膨胀率增大。会造成过饱和度、成核率、凝结质量份额和液滴生长率相应地增大。     

基于迭代学习控制的飞机全电刹车系统的研究

通过对飞机全电刹车系统模型的分析,结合迭代学习控制的特点设计出一种新的全电刹车系统的控制律。通过在matlab/simulink中仿真,取得了理想的效果,表明控制律的设计基本合理、可行。     

波音737NG飞机平尾内梁下蒙皮裂纹的修理

介绍了水平安定面内梁下蒙皮裂纹的成因以及发现裂纹后的修理方法，结合定检维修经验对裂纹损伤修理方案和经常出现的问题进行了分析总结，并给出了修理工期控制的建议。     

磁选态单束铯束管束光学参数的模拟计算和设计

为提高铯束管跃迁信号强度,在束光学参数设计中,用蒙特卡罗方法模拟计算铯原子通过率和未跃迁比例。通过改变模拟计算中的束光学参数,分析铯原子通过率、未跃迁比例和倍增器首极电流的变化趋势,得到了主要束光学参数的合理取值范围。在铯束管实际装配和试验中使用束光学参数设计结果,有效地增加了倍增器首极电流。     

赛斯纳172R飞机空速管异物堵塞的成因及防范分析

对发生在赛斯纳172飞机上空速管堵塞的故障进行了收集、统计、分析,对空速管堵塞的原因进行分析,并提出了有效的防范措施。     

低速大转矩永磁游标电机在发酵罐中的应用

采用秸秆生产丁醇时,为了达到高效率发酵,需要使发酵液中菌体分布均匀,所加物料需要及时搅拌。工业化生产丁醇的发酵罐尺寸较大,搅拌过程对驱动电机的输出转矩要求较高,因此高效率、小体积、低速大转矩的秸秆发酵搅拌电机对工业化发酵生产丁醇意义重大。设计了一种定转子永磁游标电机用于发酵液搅拌,并对电机的槽极数、电磁性能进行了具体的研究。制造样机并采用滞环控制实现了对液态发酵对象的快速响应,且实现了低能耗、高效率的发酵过程。     

Advances and trends in plastic forming technologies for welded tubes

With the implementation of environmental protection, sustainable development and conservation-oriented policies, components and parts of thin-walled welded tubes have gained increasing application in the aircraft and automotive industries because of their advantages: easily achieving forming and manufacturing process at low cost and in a short time. The current research on welded tube plastic forming is mainly concentrated on tube internal high-pressure forming, tube bending forming, and tube spinning forming. The focuses are on the material properties and characterization of welded tubes, finite element modeling for welded tube forming, and inhomogeneous deformation behavior and the mechanism and rules of deformation coordination in welded tube plastic forming. This paper summarizes the research progress in welded tube plastic forming from these aspects. Finally, with a focus on the urgent demand of the aviation, aerospace and automotive industries for high-strength and light-weight tubes, this paper discusses the development trends and challenges in the theory and technology of welded tube plastic forming in the future. Among them,laser tailor-welded technology will find application in the manufacture of high-strength steel tubes.Tube-end forming technology, such as tube flaring and flanging technology, will expand its application in welded tubes. Therefore, future studies will focus on the FE modeling regarding how to consider effects of welding on residual stresses, welding distortions and microstructure, the inhomogeneous deformation and coordination mechanism of the plastic forming process of tailor-welded tubes, and some end-forming processes of welded tubes, and more comprehensive research on the forming mechanism and limit of welded tubes.     

金属弹簧管性能影响因素的仿真分析

为了研究高温密封组件金属弹簧性能,本文通过对波音公司编网状弹簧管结构和Streck心脏支架结构的研究,建立了编织弹簧的几何拓扑构型和数学模型,推导了弹簧直径计算公式。采用AUTODESK3D-MAX构建了编织弹簧的仿真模型,用ANSYS仿真软件分别从编织丝直径、编织密度以及编织方法 3方面探究不同测试对弹簧性能的影响。结果表明,增加弹簧丝直径、降低弹簧管轴向方向的编织密度、提高圆周方向的编织密度、向外的弹簧管编织方式可有效提高弹簧管的回弹性能。     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

磁转速表指针摆动的故障分析

就磁转速表活动系统的动态特性以及在附加交变力矩的作用下，指针摆动随转速变化的规律，从理论上进行了分析，并结合实际探讨了指针摆动的故障原因。