故障注入技术在飞行器非电系统中的应用进展

故障注入是一种基于试验的测评方法，是飞行器综合健康管理的重要组成部分，在提高飞行器的安全性方面具有重要作用。本文介绍了故障注入技术的基本原理，详细阐述了故障注入的各种实现方法在飞行器中的应用现状，重点分析了故障注入技术在飞行器结构、防热、液压、机械等非电系统应用中的关键技术以及存在的技术难点，并展望了该领域的发展。     

Adaptive feedback control of stability in an axial compressor with circumferential inlet distortion

The adaptive feedback control of stability with circumferential inlet distortion has been experimentally investigated in a low-speed, axial compressor. The flat-baffles with different span heights are used to simulate different distorted inflow cases. Compared with auto-correlation and root-mean-square analysis, cross-correlation analysis used to predict early stall warning does not depend on the distortion position. Hence, the cross-correlation coefficient was used to monitor the stable status of the compressor and provide the feedback signal in the active control strategy when suffering from different distortions. Based on the stall margin improvement of tip air injection obtained under different distorted inflow cases and the sensitivity analysis of cross-correlation coefficients to injected momentum ratios, tip air injection was adopted as the actuator for adaptive feedback control. The digital signal processing controller was designed and applied to achieve adaptive feedback control in distorted inflow conditions. The results show that the adaptive feedback control of air injection nearly achieves the same stall margin improvement as steady air injection under different distortion intensities with a reduced injection mass flow. Thus, the proposed adaptive feedback control method is ideal for the engine operation with circumferential distorted inflow, which frequently occurs in flight.     

A numerical study of segmented cooling-stream injection in supersonic film cooling

The present study proposes a segmented cooling-stream injection structure based on a certain coolant mass flow rate, and numerically investigates the effect of segmented cooling-stream injection on supersonic film cooling. The results indicate that without shock-wave impingement and with helium as the coolant, segmented cooling-stream injection can reduce the mixing between the mainstream and the cooling stream to produce better cooling performance than single injection, especially at larger coo...     

叶顶间隙偏差对叶片气动性能影响的不确定性研究

在压气机叶片加工过程中，实际加工得到的叶片外形与设计叶型不可避免会存在一些偏差。为研究叶片叶顶间隙尺寸波动对性能的影响，以Rotor37为研究对象，采用三维定常数值模拟方法，基于非嵌入式混沌多项式中二维正态分布变量产生方法，分别对叶片前缘叶顶间隙和尾缘叶顶间隙进行尺寸波动干扰，研究了叶顶间隙不确定性对气动性能和流场的不确定性影响，评估了公差带内叶顶间隙偏差与气动性能变化的相关性，并探究了叶顶间隙变化对叶片稳定裕度的影响机理。研究发现，叶顶间隙偏差对等背压条件下叶片质量流量、等熵效率和总压比的平均水平几乎不会造成影响；叶顶间隙偏差所造成的气动性能分布标准差随工况点向不稳定边界的逼近而逐渐增大。同时，叶顶间隙不确定性会导致样本稳定裕度均值有所降低，不确定性分析中稳定裕度均值相对原型叶片下降了2.42%。流场结构方面，叶顶间隙偏差主要影响80%叶高以上部分流场；叶顶间隙偏差对叶顶区域泄漏流产生的影响，导致了叶片稳定裕度的变化。     

涡轮动叶部分吸力侧肩壁凹槽状叶顶气热和冷却性能研究

为了获取高性能的燃气涡轮动叶叶顶结构和气膜冷却布局，采用数值求解三维Reynolds-Averaged Navier-Stokes (RANS) 方程和标准 湍流模型的方法研究了涡轮动叶部分吸力侧肩壁的凹槽状叶顶气热和冷却性能。数值模拟得到的动叶平叶顶传热系数与实验数据吻合良好，验证了数值方法的准确性。对比0.95吹风比时动叶凹槽状叶顶沿中弧线和近压力侧布置的2种气膜冷却布局的叶顶泄漏流动形态、传热系数和气膜冷却有效度，指出近压力侧的气膜冷却布局B的总压损失大于沿中弧线的气膜冷却布局A；但近压力侧的气膜冷却布局B具有更好的冷却效果。基于近压力侧气膜冷却布局的凹槽状叶顶结构，通过切除尾缘处不同轴向长度的吸力侧肩壁，设计了5种不同的部分吸力侧肩壁的叶顶结构。结果表明：切除10%吸力侧肩壁的Case 7能有效降低总压损失，平均总压损失系数相比完整肩壁的Case 2降低了6.3%；叶顶净热流密度减少和传热系数分布与Case 2基本相同，尾缘处的冷却效率因冷气受到压制附着于叶顶而提高。     

低反力度跨声速转子的叶顶喷气扩稳数值研究

为进一步提高低反力度压气机的稳定工作范围，以某三级低反力度高负荷压气机首级跨声速转子为研究对象，借助三维数值模拟方法，进行了叶顶喷气扩稳研究，分析讨论了叶顶喷气提升低反力度压气机转子稳定性的机理，并探讨了不同喷气轴向位置对扩稳效果及气动性能的影响。结果表明：叶顶喷气通过削弱叶顶泄漏涡和通道激波的相互作用，抑制了转子近失速工况下泄漏涡的破碎，消除了叶顶通道的大面积堵塞，拓宽了转子的稳定工作边界；随着喷嘴的位置从叶顶前缘处沿轴向上游移动，转子的失速裕度提升量呈现出先增大后减小的趋势，综合扩稳效果和对压气机总性能参数的影响，最佳喷气轴向位置为叶顶前缘上游转子5%叶顶轴向弦长处；叶顶喷气改变了转子气动参数的径向分布，降低了转子上15%叶高范围内的负荷，同时也使得其它叶高区域的负荷提升。