板料成形的数值分析及程序系统

本文讨论了板料成形的数值分析方法,并介绍一个能在微机上运行的程序系统——CASF(Computer Aided Sheetmetal Forming)01系统。 CASF01系统采用参数三次样条描述板金零件的几何外形,按弹-塑性流动理论用完全拉格朗日有限元法计算成形过程中的应力应变分布。由于参数样条的插值性和分段描述特点与有限元法的结构离散在基本思想和处理方法上的相似性,系统内曲面描述和力学分析程序间数据传递迅速方便。圆板胀形及其汽车零件的计算实例表明了CASF01系统的可靠性和实用性。     

Cyclotron masers and solar spike bursts

The theory of electron cyclotron maser emission and its application to solar spike bursts are reviewed. By analogy with the Earth's AKR, three sources of free energy are considered: a loss-cone anisotropy, a velocity-space hole, and a trapped distribution. The problem of how the radiation escapes through the second harmonic absorption layer is emphasized. Harmonic emission due to z mode coalescence may operate for some bursts, but the 2–5s delay between hard X-ray bursts and spike bursts suggests that some other mechanisms is required for most spike bursts. A model involving formation of a trapped distribution in low-density regions neighboring the flaring flux tube is considered.     

计算机辅助任意多边形排料

 本文描述了一种计算机辅助排料的算法。它能自动处理二维不规则形状物体的排料。排料的处理过程分为两个阶段。现介绍的为第一阶段的算法。计算实例表明,该方法可以明显减少计算量。并具有原材料利用率高的特点。 飞机蒙皮等钣金件的下料就涉及到大量的排料问题,在整张的金属板材上排成所需要的零件形状。     

壁压法在非矩形风洞中的应用

 解决大攻角洞壁干扰修正的壁压法,是利用一定数量固定位置和形状的线源和线涡来模拟风洞内模型的堵塞效应和升力效应。矩形风洞实验段边界对绕模型流动的影响,可用两个方向有限层的镜像线源和线涡来代替,并利用在风洞上下壁和侧壁上测压点处测量所得     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Experimental Aspects of Mid-Frequency Pulsations (f≈10–100 mHz) in the Southern Polar Cap

We review the results obtained in the frequency range of Pc3 (22-100 mHz) and Pc4 (7-22 mHz) pulsations at Italian Antarctic stations in the southern polar cap (“Mario Zucchelli”, at Terra Nova Bay, TNB, 80^˚.S; “Concordia”, the Italian/French base at Dome C, DMC, 89^˚.S). The absence of a midnight enhancement in the pulsation power suggests a negligible substorm influence at extreme latitudes, while the sharp noon enhancement, which appears only at TNB, is determined by the closer proximity of the station to cusp related phenomena. The relationship between the frequency of the band-limited signals and the interplanetary magnetic field strength, the cone angle influence, and the higher correlation of the Pc3 power with the solar wind speed in the morning hours suggest a global scenario in which upstream waves would be mainly responsible for the mid-frequency activity in the polar cap. However, the polarization pattern is odd with respect to the predictions for tailward propagating modes.     

强激波-附面层干扰下的气流动态畸变研究

本文在一定附面层条件下,着重研究典型的强激波与紊流附面层干扰区下游扩压器出口的气流动态畸变,文中讨论了激波强度、扩压器壁面形状(直壁和曲壁)对动态畸变的影响.讨论了紊流度分布中四个峰值与相同截面上的总压沿高度分布的相互关系.最后对紊流度沿高度分布中的若干典型站的总压信号作功率谱密度和概率密度函数分析     

热暴露对B/Al复合材料性能的影响

对经300℃、500℃高温热暴露的B／Al（LF6）复合材料的力学性能进行了研究，实验结果表明材料在300℃下热暴露时，性能下降速度较慢，100h后强度保留率约为76％，延伸率保留率为74％。而在500℃下热暴露时，5h以上强度就有明显降低。高温长时间热暴露后复合材料的断裂也从积累型转变为典型的非累积型断裂。通过透射电镜（TEM）及扫描电镜（SEM）对固态热压制造态和主温热暴露的界面状况进行了分析，认为界面反应是造成B／Al复合材料力学性能下降的主要原因。     

嵌入式网关技术在门禁控制系统中的应用

随着计算机网络技术的发展和普及，目前出现了以单片机技术和以太网技术为核心的嵌入式网关技术，采用嵌入网关技术，可在局域网环境下采用TCP/IP协议实现门禁控制控制器同后台服务器的数据交换。其优点是技术先进、数据传输速度高、工程成本低、可靠性和安全性高。在论述了嵌入式网关工作原理的基础上，重点讨论了嵌入式网关中的门禁控制器的应用问题。     

翼型风洞侧壁干扰的数值模拟研究

运用Navier-Stokes数值模拟对翼型模拟试验对风洞侧壁干扰进行模拟，将简单代数湍流模型扩展用于机翼／风洞侧壁结合区流动，分析了风洞实验侧壁干扰问题的形成机理和影响翼型实验侧壁干扰的各种因素，如翼型展长、风洞侧壁边界层厚度及侧壁边界层抽吸等，对实验结果的影响，得出了一些有用的结论。计算格式空间采用中心有限体积离散，时间采用多步Runge-Kutta时间步长格式进行积分。计算结果证明了该方法的可行性和优越性。