不同喷铝参数对复合材料雷击防护性能模拟

为了研究复合材料不同的雷击防护(lightning strike protection,LSP)系统在雷电流作用下的损伤规律,对雷击损伤过程和烧蚀机理进行分析,建立复合材料层合板雷击防护的能量平衡数学模型。在此基础上,在ABAQUS中建立复合材料基准件、全喷铝和局部喷铝防护系统的碳纤维增强复合材料(carbon fiber reinforced polymer,CFRP)层合板电-热耦合有限元模型,和实验结果对比验证模型的有效性,对雷击烧蚀损伤特征进行分析,并引入雷击烧蚀损伤指数DI,得出三种不同模型在不同铝涂层厚度、不同峰值雷电流作用下的烧蚀损伤规律,并对两种不同的局部喷铝防护系统下复合材料的损伤特征进行对比分析。结果表明:雷击防护系统下复合材料的烧蚀损伤面积和铝涂层厚度关系进行函数拟合,两者均满足幂函数关系。     

Microstructure,thermophysical property and ablation behavior of high thermal conductivity carbon/carbon composites after heat-treatment

Uni-directional carbon/carbon composites with high thermal conductivity are suitable to supply continuous thermal protection for future reentry vehicles since they could reduce surface temperature and ablation rates simultaneously in harsh environments. In this work, the high thermal conductivity carbon/carbon composites were prepared by chemical vapor infiltration. After heat-treatment, both their open porosity and internal friction increase due to the fiber/matrix thermal expansion mismatch; while their thermal conductive performance become better due to more complete carbon structure. With raising heat-treatment temperature from 1800 °C to 2450 °C, the mass and linear ablation rates of C/C composites with fibers vertical to the oxyacetylene torch for 60 s decrease from 0.66 mg/s and 2.95 μm/s to 0.51 mg/s and 2.05 μm/s respectively. The improved ablation resistance is resulted from the increased thermal conductivity from 282 to 508 W/(m·K) and more carbon fibers exposed to the flame during ablation, which have better oxidation resistance than those of carbon matrix. While such ablation rates become larger for composites with fibers parallel to the flame, from 1.02 mg/s and 3.73 μm/s to 1.28 mg/s and 5.01 μm/s respectively since the ablation occurred more easily through gaps at the fiber/matrix interfaces, which become larger and are always exposed to the flame for this case.     

FINITE DIFFERENCE MODEL FOR SIMULATION OF DENSIFYING CARBON-CARBON COMPOSITES BY CHEMICAL VAPOR INFILTRATIONP ROCESSES

ＮｏｍｅｎｃｌａｔｕｒｅｓＡ０—ｃｏｅｆｉｃｉｅｎｔｏｆｔｈｅＡｒｈｅｎｉｕｓｅｑｕａｔｉｏｎＣ（ｎ）—ｈｙｄｒｏｃａｒｂｏｎｃｏｎｃｅｎｔｒａｔｉｏｎｉｎｕｎｉｔ（ｎ）（ｍｏｌ／ｃｍ３）Ｃ０—ｈｙｄｒｏｃａｒｂｏｎｃｏｎｃｅｎｔｒａｔｉｏｎａｔｅｘ...     

STATIC AND FATIGUE BEHAVIOR OF IMPACTED AS4/PEEK THERMOPLASTIC COMPOSITES UNDER COMPRESSION LOAD

Static and fatigue tests under compression load were made on impacted AS4/PEEK and T300/913C graphite/epoxy with ［45/90/-45/0］_5S stacking sequence. The comparison of the damage tolerance assessment for thermosetting and thermoplastic composites shows that thermoplastics are more damage tolerant under compression. Impacted thermoplastic composites have excellent compression-compression fatigue behavior. The damage growth life is only a few percent of their total fatigue life and no regular damage growth can be found. Some design principles for thermosetting composite structures may still be used.     

旋转CVI制备陶瓷基复合材料碳界面层

用旋转ＣＶＩ工艺，通过优化工艺参数，在低压（５ｋＰａ）、高温（１１００℃）、高Ｃ３Ｈ６ 浓度（６２．５ｖｏｌ％ ）以及３．５ｍ ｍ ·ｍ ｉｎ－ １ 碳布旋转线速度条件下，在二维碳布上快速制备了厚度均匀（０．２５μｍ ）、表面规整的致密热解碳界面层。实验结果表明：沉积温度对界面层表面状况有较大的影响；采用减压法与优化沉积炉结构与几何尺寸，能有效防止高温高Ｃ３Ｈ６ 浓度下炭黑的形成。     

PULSED Nd-YAG LASER WELDING OF AN AI-SiC_p METAL MATRIX COMPOSITE

SupportedbytheNationalNaturalScienceFoundationofChinaThefewweldingtechniques,includinggastungstenarcwelding,gasmetalarcweldingandelectronbeamwelding,whichhavebeenexploredforjoiningofMMCs,werefoundtobeunsatisfactorymainlyduetotheformationofexcessivebrittleAl-carbidephase["2'J.Never-theless,limitedsuccesshasbeenachievedinusingCO,laserstoweldcertaintypesofAl-Si/SiCMMCs[s'J.Themeritsoflaserweldingareapparent:theintrinsicfocusingabilityandtheca-pabilityofhavingprecisecontroloverthelaserpro…     

TiC/Al复合材料在锌液中均匀化机理分析

采用自蔓延高温合成（SHS）法制备高TiC颗粒含量的TiC／Al复合材料。利用自制的实验装置研究复合材料中TiC颗粒在静止锌液中的均匀化过程。结果表明：当锌液温度低于铝的熔点时，TiC／Al复合材料置于锌液后，锌向其内部扩散，引起复合材料表层内液相线温度降低，当表层内Al-Zn合金的液相线温度等于或低于锌液温度时，Al-Zn合金便处于熔融状态，TiC颗粒随其一起从TiC／Al复合材料块上脱落，并不断地向锌液内部传输，最终均匀分布在锌液中；而当锌液温度高于铝熔点时，TiC／Al复合材料置入后，锌和铝同时进行扩散，但是当复合材料表面温度达到铝熔点时，铝开始熔化，铝的熔化导致TiC颗粒的脱落，脱落下来的TiC颗粒不断向锌液内部传输，最终均匀分布在锌液中。     

碳纤维的表面处理与复合材料的层间剪切强度

碳纤维增强塑料（ＣＦＲＰ）是碳纤维在当前应用的主要形式之一。实用要求ＣＦＲＰ层间剪切强度（ＩＬＳＳ）的下限值为７ＳＭＰａ，未经表面处理的碳纤维的ＩＬＳＳ仅在５０～６０ＭＰａ之间，经表面处理后，可提高到８０ＭＰａ以上，充分满足使用要求。除此之外，ＩＬＳＳ还与纤维含量、孔隙率和基体树脂性能等有关。     

熔铝氧化渗透合成SiC_p/Al_2O_3-Al复合材料的微观结构分析

以低成本的熔铝氧化渗透合成新方法制备了SiCp/Al2 O3 Al复合材料。借助X光电子谱 (XPS)、光学金相显微镜、透射电镜 (TEM)、X射线衍射 (XRD)等手段研究了该种复合材料的微观结构 ,并分析了影响微观结构的主要因素及其影响规律。结果表明 ,Al2 O3 和Al作为复合材料基体呈双连续分布 ,它们各自的含量可在较大范围内受SiC颗粒的粒度所控制。在熔铝氧化渗透合成的SiCp/Al2 O3 Al复合材料中 ,各组成相之间无界面反应 ,也无晶间相 ,Al2 O3 在SiC颗粒表面二次形核并直接生长的现象普遍存在 ,并由此形成了具有良好物理冶金结合的Al2 O3 SiC一体化陶瓷骨架     

适合航空航天用SiCp/Al复合材料的性能

采用粉末冶金法制备了Φ300 mm的15%(体积分数)SiCp/A l复合材料坯锭,研究了热挤压、锻造后的材料力学性能以及断裂特点。结果表明,该材料的弹性模量在97 GPa、拉伸强度保持在550 MPa的水平下,延伸率仍高达7%左右,旋转弯曲疲劳强度在250~290 MPa范围内,断裂韧性为25 MPa.m1/2,冲击韧性为62.5 kJ/m2。与棒材挤压态相比,T4态复合材料拉伸强度和屈服强度分别提高66.7%和100%,但塑性保持在同一水平。断口观察表明,挤压态复合材料以基体韧性断裂为主要形式,而T4态复合材料除了基体韧性断裂外,还存在SiC颗粒断裂现象。挤压棒材锻造后有利于提高材料的横向强度。