单晶高温合金接近使用条件下的寿命估算与损伤分析

针对发动机热端部件承受的典型载荷谱，发展了一种通用的寿命预测方程和损伤分析方法。这个方法是在疲劳蠕变交互作用断裂特征图及其最大应力修正的寿命方程基础上建立的。根据ＤＤ３单晶合金的疲劳蠕变交互作用断裂特征图及其最大应力修正的寿命方程，验证了本方法是切实可行的。预测精度是符合要求的。     

钼-铌合金原料品质对单晶制备的影响

主要讨论了钼-铌合金原料品质,包括烧结条的制备、原料的化学成分、原料棒的尺寸规格等对单晶制备的影响。结果表明:高温真空烧结钼-铌合金烧结条由于C、O等杂质含量过高,在20 kW电子束悬浮区域熔炼炉上区域熔炼时未能直接生长制备出单晶,但其经过两次电子束熔炼获得的Ф(12~17)mm原料棒C元素质量分数降为6.3×10-3%、O元素质量分数降低了近2个数量级,仅为1.4×10-3%,能稳定地生长制备出Ф31 mm×735 mm的大尺寸钼-铌合金单晶,而直径超过Ф18 mm或小于Ф11 mm原料棒在区域熔炼时未能获得钼-铌合金单晶。     

航空绞车综合测量系统的设计与实现

简要介绍了航空绞车综合测量系统的功能、组成、工作原理及软硬件设计。     

变频信号的测量方法

本文阐述了单片机测量车用电子警报器变频信号的原理和方法。     

激波过弯道绕双圆柱流场

采用单曝光光栅干涉或双曝光光栅干涉，研究激波过弯道绕双圆柱传播的微波流场。采用单曝光法，成功显示入射激波到第一圆柱上的反射、绕射，到达第二圆柱上的反射、绕射。在同一底片上采用双次曝光，第一次脉冲记录直道上的平面波，第二次脉冲记录激渡过弯道绕双圆柱流场。这些照片对于研究反射、绕射及它们边界的相互作用是很有用的。     

磁选态单束铯束管束光学参数的模拟计算和设计

为提高铯束管跃迁信号强度,在束光学参数设计中,用蒙特卡罗方法模拟计算铯原子通过率和未跃迁比例。通过改变模拟计算中的束光学参数,分析铯原子通过率、未跃迁比例和倍增器首极电流的变化趋势,得到了主要束光学参数的合理取值范围。在铯束管实际装配和试验中使用束光学参数设计结果,有效地增加了倍增器首极电流。     

Hierarchical space–time block codes signals classification using higher order cumulants

An efficient method for blind classification of space–time block codes(STBCs) based on fourth-order cumulants is proposed for a single receiver antenna.This paper presents a model of received STBCs signals in multiple input single output(MISO) communication systems and applies the characteristics of coding matrices to derive analytical expressions for the fourth-order cumulants to be used as the basis of an algorithm.The fourth-order cumulants at various delay vectors present non-null values that depend on the transmitted STBCs.Tests of nullity are accomplished by hypothesis testing.The proposed algorithm avoids the need for a priori information of modulation scheme,channel coefficients,and noise power.Consequently,it is well suited for non-cooperative scenarios.Simulations show that this method performs well even at low signal-to-noise ratios(SNRs).     

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.     

单斜面膨胀喷管几何参数对流场和性能的影响

基于CFD技术,通过求解R eynolds平均N-S方程附以标准k-ε双方程湍流模型,数值研究了单斜面膨胀喷管(SERN)主要几何参数对其内部流场和性能的影响,计算结果表明,SERN扩张段上、下斜面长度和角度对喷管流场结构和性能有明显的影响,随着上斜面长度的增加,喷管从欠膨胀状态过渡到过膨胀状态,在完全膨胀状态下,推力系数最大,存在某一最佳的上斜面角度,在该角度下,喷管推力系数最大,同样地,对于下斜面也存在最佳斜面长度和角度。      

基于单应性矩阵的模型迎角单目视频测量方法

风洞试验中模型迎角的精准测量是降低阻力系数误差的重要途径之一,为此,提出了基于单应性矩阵的模型迎角单目视频测量方法。该方法通过两个单应性矩阵,获取试验过程中相机实时位姿和标记点物方空间位置坐标,应用坐标旋转关系,完成试验模型的迎角测量。数值仿真试验结果表明：迎角测量误差与待测标记点到风洞壁板间的距离偏差近似为线性关系,因此,当标记点不满足共面条件时,可根据该特点进行测量误差修正。静态标定和风洞迎角测量试验结果表明：修正系统误差后,迎角实测数据的测量准度在0.01°以内,精度不超过0.012°。本文方法易于实施,工程实用价值强。