基于Deform软件二次开发和BP神经网络的TA15多向锻造微观组织预报

通过热压缩实验构建了TA15合金的热变形真应力-应变曲线,以此为基础分别建立了合金双相区及单相区温度区间的热变形本构方程;基于热压缩试样动态再结晶的统计数据建立了TA15合金的动态再结晶模型。借助Deform提供的二次开发功能实现相关数学模型的程序化,制定正交实验方案,实现了TA15合金多向锻造变形的微观组织仿真。通过正交实验分析得出各项因子的影响对象及强弱差异,提出了双相区及单相区温度区间内的多向锻造最佳因子组合。建立了TA15合金多向锻造变形微观组织的BP （Back Propagation）神经网络预测模型,将预测结果与有限元仿真结果进行比较,结果表明两种方法的预测结果基本一致,但神经网络具备有限元仿真难以实现的良好细节预测能力,能更为细致地实现对微观组织分布状态的划分。     

厚度和环境对复合涂层导电性能的影响

为了给数字化刻铣曲面频率选择表面(FSS)结构的制作和加工提供参考和依据,对比研究了含片状银粉颗粒的聚氨酯基和环氧树脂基2种复合导电涂层的基本性能,并通过环境加速试验,重点研究了温度、湿度以及腐蚀气氛对2种导电涂层的界面强度、微观结构和导电性能的影响.通过电桥法测量涂层表面电阻的变化,并通过扫描电境观察环境试验前后,涂层表面和剖面的微观结构和形貌变化.试验结果表明:聚氨酯基涂层的综合性能优于环氧树脂基涂层;在实验所涉及的参数变化范围内,环境因素对2种涂层与基体的界面结合影响不大,但对其导电性能的影响比较明显.环境因素对导电性能的削弱作用,源于相应过程中导电涂层的微观结构损伤.     

类芬顿反应在碳化硅光学材料研抛中的作用

本文讨论了以零价铁代替亚铁盐形成类芬顿反应(Fenton-Kind process)体系应用于碳化硅光学材料抛光过程中的反应机理,通过双转子研抛机床对SiC光学材料进行了研抛实验,验证了类芬顿反应能够有效地提高SiC材料的加工效率和加工质量。通过对比不同磨料粒度研抛液加工结果,获得了SiC材料研抛过程中化学与机械作用规律。     

激光辐照条件下光电电池温度特性的实验研究

激光输能具有广阔应用前景,而光电电池是激光输能技术中实现光-电转换的核心部件。文章围绕温度对光电电池输出性能的影响,通过建立电池输出性能实验测试系统,研究了一定激光功率密度下砷化镓电池和硅电池在不同温度下的伏安特性,以及开路电压、短路电流、最大输出功率、匹配负载、转换效率、填充因子随电池温度的变化规律,并给出其定量表达式,可为激光输能条件下光电电池的选择以及光电电池温度特性预测提供参考。     

Effect of Semi-solid Isothermal Heat Treatment on Microstructure of VW63Z Alloy

The effects of isothermal heat treatment on the semi-solid microstructure evolution of VW63Z (Mg-6Gd-3Y-0.4Zr, wt.%) alloy are studied. It shows that the microstructure of VW63Z alloy could transform from equiaxed crystal to semi-solid spherical crystal after isothermal heat treatment above 620 ºC. With the heating temperature elevating from 620 ºC to 635 ºC and the holding time prolonging from 10 min to 35 min, the liquid fraction increases gradually. The semi-solid microstructure evolution of VW63Z alloy can be divided into three stages, i.e., particle coarsening and spheroidization;particle necking, coalescence, and Ostwald ripening;and dynamic equilibrium. The semi-solid process window of VW63Z alloy ranges from 620 ºC to 635 ºC, where the best process parameters are holding at 635 ºC for 20 min?30 min. The solid fraction, the average particle size, and the shape factor are 41.1%?53.8%, 81.5 μm?83.2 μm, and 0.70?0.75, respectively. The maximum relative deviations of the solid fraction, the particle size, and the shape factor at different heights of the same billet are 44.6%, 17.4%, and 16.6%, respectively, which means that it should pay attention to the uniformity of edge and core of VW63Z alloy during isothermal heat treatment. The driving force of microstructure is supposed to be the reduction of solid-liquid interface free energy.     

Investigation of vertical profile of rain microstructure at Ahmedabad in Indian tropical region

The microstructure of rain has been studied with observations using a vertical looking Micro Rain Radar (MRR) at Ahmedabad (23.06°N, 72.62°E), a tropical location in the Indian region. The rain height, derived from the bright band signature of melting layer of radar reflectivity profile, is found to be variable between the heights 4600 m and 5200 m. The change in the nature of rain, classified on the basis of radar reflectivity, is also observed through the MRR. It has been found that there are three types of rain, namely, convective, mixed and stratiform rain, prevailing with different vertical rain microstructures, such as, Drop Size Distribution (DSD), mean drop size, rain rate, liquid water content and average fall speed of the drops at different heights. It is observed that the vertical DSD profile is more inhomogeneous for mixed and stratiform type rain than for convective type rain. It is also found that the large number of drops of size <0.5 mm is present in convective rain whereas in stratiform rain, drops concentration is appreciable up to 1 mm. A comparison of measurements taken by ground based Disdrometer and that from the 200 m level obtained from MRR shows good agreement for rain rate and DSD at smaller rain rate values. The results may be useful for understanding rain structures over this region.     

纳米TiC粉末改性钎料钎焊CBN磨粒的结合界面和磨损特性

采用了Ag-Cu-Ti 合金和纳米 TiC 粉末组成的新型复合钎料钎焊立方氮化硼(CBN)磨粒和工具基体,运用了三维体式显微镜和扫描电镜,研究了CBN磨粒与改性钎料之间的结合体系,包括界面微结构和反应产物,并进行了钎焊磨粒耐磨性试验.试验结果表明:加入的纳米TiC粉末均匀分布在钎料层内,细化了Ag-Cu-Ti合金钎料层的显微组织,有效控制了CBN磨粒与钎料的剧烈反应;磨粒表面化合物均匀致密,确保了CBN磨粒、纳米改性钎料和基体之间的结合强度;钎焊CBN磨粒的磨损形式以磨耗磨损为主,后期出现微小破碎,无磨粒脱落.     

Ti-6Al-4V钛合金激光弯曲成形微观组织研究

以1mm厚Ti-6Al-4V合金薄板为对象,运用光学金相显微镜、电子探针、扫描电子显微镜、氮氢氧联合分析仪、显微维氏硬度计,研究了特定累积线能量下90°弯曲角弯折区显微组织。结果表明,弯折区组织与累积线能量输入有关,当累积线能量在适当范围时,材料堆积增厚,极表层出现轻微复熔铸态组织,上层为板条马氏体α′,中层为针状马氏体α′,底层为长大粗化的(α+β)组织;距表层约0.2mm范围吸收间隙元素强烈致使硬度急剧提高并呈明显梯度;累积线能量输入过大,弯折区出现大面积复熔铸态组织并伴有裂纹产生。     

电子照射对硅漂移探测器性能的影响

由于高能电子辐射的长期照射,新一代太阳X射线探测器硅漂移传感器的探测性能可能发生变化.通过用电子放射源模拟空间电子对硅漂移探测器进行辐射照射试验,以测试电子照射对传感器能量分辨率、效率、信号幅度等性能的影响.试验结果表明,长期的电子照射造成硅漂移探测器面损伤和体损伤,使其漏电流增大,信号幅度减小,能量分辨率也受到照射的影响,而探测效率未发生变化.