循环湿热环境下碳纤维复合材料的界面性能

针对CCF300/5428复合材料在循环湿热环境下的吸湿-脱湿行为和层间剪切性能进行了研究,并结合扫描电镜观察了循环湿热处理的不同阶段纤维/基体界面结合状态.研究结果表明:经过反复吸湿后,水分的初始扩散速率和饱和吸湿率增加;脱湿后水对复合材料层间剪切性能的影响大部分可以消除;复合材料吸湿后室温环境下性能下降较少,但在高温高湿环境下,复合材料的性能会显著降低.     

月面巡视探测器动力学建模

动力学模型是研究星球探测车运动的基础。以某月面巡视探测器原理样机为背景,建立了其动力学模型,并进行了数值仿真分析。在说明月壤机械特性的基础上,结合地面车辆力学的知识,分析了松散月壤上刚性车轮的受力,考虑了主动驱动和被动驱动的情形,利用数学拟合的方法得到了满足工程要求的简化模型。在一定假设条件下,以牛顿欧拉法建立了三自由度整车动力学模型,建模时同时考虑了驱动和转向的相互影响。最后,数值仿真结果定性地验证了月面巡视探测器动力学模型的正确性。     

频率选择表面传输特性的温度循环效应

根据国家军用标准GJB 150-86对不同涂层材料和加工工艺的频率选择表面(FSS,Frequency Selective Surfaces)进行了温度循环的环境模拟试验,通过比较温度循环前后FSS的谐振频率、传输损耗、频带宽度和入射角稳定性等传输特性的差异,考察FSS在温度循环条件下的性能稳定性.结果表明,温度循环对不同材料和工艺的FSS的传输性能有较大影响,主要表现在FSS的传输损耗和频带宽度两方面.不同FSS在经过温度循环后,谐振频率下的传输损耗增大0.5~3倍,入射角越大增大的幅度越大;频带宽度增加50%~70%,不同的FSS增加的幅度不同.而对谐振频率和入射角稳定性的影响根据不同的FSS而不同,但对二者的影响都不明显.与简单振子FSS相比,组合振子FSS的传输性能受温度循环的影响较大.      

Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.     

舰载机壁板剪切后屈曲承载能力预测与试验验证

舰载机着舰撞击对机翼盒段产生巨大的扭矩,蒙皮以剪切形式承受扭矩,这是机翼壁板的重要设计工况。为准确预测加筋壁板剪切后屈曲承载能力,采用MSC.NASTRAN软件MRIKS弧长法,将线性屈曲分析的一致模态缺陷位移作为扰动引入后屈曲分析。考虑材料和几何双重非线性,对整体加筋壁板剪切试验件的后屈曲破坏过程进行模拟、对承载能力进行预测。根据剪切试验结果,进行对比分析。结果表明：有限元模拟的加筋板初始屈曲发生在蒙皮上,长桁足够大的相对刚度使得长桁与蒙皮连接线上出现屈曲节点,随着载荷增大,加筋壁板整体"坍塌",与试验现象一致。有限元分析（FEA）得到的初始屈曲载荷与试验结果的误差为1.25%,预测的极限承载载荷与试验破坏载荷的误差为2.4%。表明引入缺陷后的MSC.NASTRAN弧长法非线性后屈曲计算能够准确预测加筋壁板剪切后屈曲承载能力,为加筋壁板剪切试验和强度设计提供了分析方法。     

含硅芳炔树脂改性氰酸酯树脂的性能

将双酚E型氰酸酯(BEDCy)与含硅芳炔树脂(PSA)用溶液共混的方法制备了共混树脂(BEDCy/PSA);通过DSC和原位红外研究了共混树脂的固化反应,使用TGA和DMA表征了树脂的耐热性能;还考察了共混树脂的介电性能和力学性能.结果表明,PSA树脂能够降低BEDCy树脂的固化温度;随着PSA树脂的添加,氮气和空气氛...     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

亚超剪切混合层燃油雾化特性试验研究

为了摸清亚超大梯度剪切混合层内直射式喷嘴的燃油雾化特性,设计了用于向亚超剪切混合流中进行燃油喷射的直射式喷嘴,建立了亚超剪切混合层中燃油雾化试验系统。利用粒子图像测速系统（PIV）,对亚超大梯度混合层中油雾场进行测量。通过改变喷嘴流量、喷射角度和喷嘴数量研究不同参数对雾化特性的影响,并应用图像处理技术对亚超大梯度剪切混合层内的油雾场进行分析,总结归纳其雾化规律。试验结果显示：随着流量增大,穿透深度会随之增大,破碎后的颗粒分布峰值所对应的液滴直径会逐渐变小,雾化效果提升;相同流量条件下,喷嘴的角度改变对雾化效果有影响,顺喷和逆喷的雾化效果均好于垂直喷射;逆喷的喷射高度最高,随着流量的增长,燃料将会碰壁;顺喷条件下,随着角度的增加,穿透长度会有所增加;综合燃油轨迹边界,逆喷的效果相对较好。相同流量条件下,喷孔个数的改变对雾化效果和穿透深度的影响不大。     

SIMULATION OF COMPOSITE NON-LINEAR MECHANICAL BEHAVIOR OF CMCS BY FEM-BASED MULTI- SCALE APPROACH

The non-linear behavior of continuous fiber reinforced C/SiC ceramic matrix composites （CMCs） under tensile loading is modeled by three-dimensional representative volume element （RVE） models of the composite. The theoretical background of the multi-scale approach solved by the finite element method （FEM） is recalled first- ly. Then the geometric characters of three kinds of damage mechanisms, i.e. micro matrix cracks, fiber/matrix interface debonding and fiber fracture, are studied. Three kinds of RVE are proposed to model the microstructure of C/SiC with above damage mechanisms respectively. The matrix cracking is modeled by critical matrix strain en- ergy （CMSE） principle while a maximum shear stress criterion is used for modeling fiber/matrix interface debond- ing. The behavior of fiber fracture is modeled by the famous Weibull statistic theory. A numerical example of con- tinuous fiber reinforced C/SiC composite under tensile loading is performed. The results show that the stress/ strain curve predicted by the developed model agrees with experimental data.     

ZnO透明导电薄膜制备及紫外辐照处理特性研究

ZnO作为一种典型的透明导电氧化物（Transparent conductive oxide,TCO）材料,具有同氧化铟锡(Indium tin oxide,ITO)相比拟的光电性能,其原料丰富、绿色环保、易于制备、生成成本低等优点使ZnO成为最有希望替代ITO的材料。本文以玻璃为衬底,利用量子点种子层作为缓冲层,采用传统水热方法制备了低成本ZnO透明导电薄膜,采用特殊的紫外光辐照工艺对薄膜进行后处理,探索薄膜生长参数和紫外光辐照处理工艺对其透光率和导电性的影响。结果表明,紫外辐照处理不影响薄膜的透光性能,而使材料的方块电阻降低3个数量级,数值从没处理时的1.5×105 Ω/□降低到 150 Ω/□,极大地提高了薄膜的电导率,为ZnO薄膜材料电导率的提高提供了一个简单高效的途径。