夹芯的典型参数对夹层板受迫振动影响分析

根据伽辽金法,用Matlab/Simulink软件对推导的经典板假设理论、一阶剪切理论蜂窝夹层板运动方程进行了数值仿真。简单算例的计算结果表明两者基本一致。基于一阶剪切理论讨论了蜂窝夹芯泊松比对蜂窝夹层板低阶频率的影响。发现当泊松比接近1时对频率响应有显著的影响。     

非离子表面活性剂在水流中的减阻机理

为探讨非离子表面活性剂的减阻机理,在实验确认表面活性剂APG水溶液（Alkyl Polyglucoside）具有湍流减阻功效的基础上,对其剪切粘度、应力松弛特性以及剪切双折射效应,使用锥板流变仪及流动双折射测试仪进行了实验研究。最大减阻率可达70％的APG水溶液,其剪切粘度在低剪切速率区域表现为牛顿流体特性,在大于临界剪切速率区域表现为“SIS”（Shear—Induced Structure）,呈现非牛顿流体特性;APG水溶液的剪切应力松弛特性与纯水基本相似,表明“SIS”并不具有粘弹性特性。由剪切双折射效应证实的的棒状胶束聚合结构和具有的较大拉伸粘度可认为是APG水溶液能够实现湍流减阻的主要原因。     

Learning to Reach to Locations Encoded from Imaging Displays

We examined the use of hand gestures while people solved spatial reasoning problem in which they had to infer motion from static diagrams (mental animation problems). In Experiment 1, participants were asked to think aloud while solving mental animation problems. They gestured on more than 90% of problems, and most gestures expressed information about the component motions that was not stated in words. Two further experiments examined whether the gestures functioned in the mechanical inference process, or whether they merely served functions of expressing or communicating the results of this process. In these experiments, we examined the effects of instructions to think aloud, restricting participants' hand motions, and secondary tasks on mental animation performance. Although participants who were instructed to think aloud gestured more than control groups, some gestures occurred even in control conditions. A concurrent spatial tapping task impaired performance on mechanical reasoning, whereas a simple tapping task and restricting hand motions did not. These results indicate that gestures are a natural way of expressing the results of mental animation processes and suggest that spatial working memory and premotor representations are involved in mental animation. They provide no direct evidence that gestures are functional in the thought process itself, but do not rule out a role for overt gestures in this type of spatial thinking.     

APPLICATION OF OPTIMIZATION TO AIRCRAFT LANDING IN WIND SHEAR

 <正> Aircraft landing in wind shear is dangerous. Many accidents have happened and a lot of research work has been done in this area. Whether an aircraft has enough capability to land in wind shear safely or not is not very clear vet. Using the real worst-case wind shear model and the optimization technique, the optima! open loop controls ol two civil aircraft landing in wind shear are found and it can easily be seen thai, generally speaking, an aircraft has potentiality to land in wind shear satelv. The problem hear is how to help the pilot detect the wind shear on board in lime and control the aircraft correctly and timelv.     

用弯剪法计算两向正交正放平板网架各杆内力

本文在节点法和截面法的基础上，将两者融为一体，为计算两向正交正放平板网架各杆内力，提供了一种新颖方法，称其为弯剪法，文中引用了实例，结果与其它方法完全一致，并符合实际，这就证实了本法的有效性和可靠性，有一定的参考价值。     

直升机在风切变气流场中的响应特性

为了研究直升机在风切变气流场中的响应特性,基于相关文献,建立了风切变工程化模型。根据旋翼的非均匀入流模型,建立了直升机非线性动力学模型,并利用四阶龙格—库塔法,对某型直升机在风切变场中的飞行特性进行了数值仿真。研究结果表明:样机进入风切变场后,飞行姿态立即出现俯仰震荡、左右摇摆的现象,10 s内,侧倾角的峰值差最大达到了73.14°,直升机下坠的高度为53.19 m,偏航距离为93.79 m。     

Yield anisotropy and tension/compression asymmetry of a Ni3Al based intermetallic alloy

In order to investigate the yielding behavior of the newly developed Ni 3 Al-based intermetallic alloy IC10, yield stresses have been measured in tension and compression with different orientations. The specimens were cut from a sheet with different angles inclined from the solidification direction. The inclined angles were taken to be 0 , 22.5 , 45 , 67.5 and 90 . All experiments were conducted at room temperature except for orientation 0 , whose deformation temperatures ranged from 298 to 1273 K. Experimental results show that the yield strength of alloy IC10 has the anomalous behavior which has been observed for other Ll 2 -long-range ordered intermetallic alloys, but it is less pronounced. The abnormalities show the following characteristics: (i) the yield strength increases as the temperature is raised below the peak temperature, (ii) yield strength anisotropy, (iii) tension/compression asymmetry. Compared to Ni 3 Al single crystals, the polycrystalline exhibits some different yielding behaviors which may be due to the high volume fraction of c phase.     

北京平原地区VS30估算模型适用性研究

本文使用基于钻孔测井数据的3类模型,即常速度外推模型、速度梯度模型、双深度参数外推模型,通过对北京地区460个深度超过30m的钻孔剪切波速资料进行分析,详细探究了V_(S30)估算模型在本研究区的适用性。研究结果表明双深度参数外推模型在估算V_(S30)上准确度很高,其不需要大量的数据进行回归分析,且不具有区域独立性,可以为全球包括北京地区场地类别划分提供依据,进而在震害快速评估中用于确定场地影响,是一种值得推广的估算模型。     

超声速平面剪切层多模态混合扰动数值分析

对Ma_c=1.2二维空间发展超声速平面自由剪切层进行扰动模态及流动结构数值分析.使用线性稳定理论和扰动直接数值模拟方法对超声速剪切层中不同流向站位的流动剖面进行扰动参数分析和局部扰动直接数值模拟,获得了剪切层不同站位处的扰动特性.通过特定单频扰动下的直接数值模拟,在剪切层的不同区域内,无相差地促发了慢模态、混合模态和快模态等多种声涡模态,得到了特定单频扰动促发的多模态无相差不稳定波.      

导弹无线电引信电磁脉冲效应仿真

以LFM导弹无线电引信为研究对象,以Ansoft软件为仿真平台,建立无线电引信天线模型和电路模型,通过计算机仿真对高功率微波(HPM)干扰导弹无线电引信的效应进行了研究。仿真结果表明,在高功率电磁脉冲作用下,混频器和滤波器上分布的电压很高,而进入执行级的电压很低,达不到启动电压的幅度。