Linear Shaped Charge Cutting Property and Charge Cutting Mechanism of Mg-Gd-Y-Zn Alloy

The linear shaped charge cutting technology is an effective technology for aircraft separation. It can separate invalid components from aircrafts timely to achieve light-weight. Magnesium alloy is the lightest metal material, and can be used to cast effective light-weight components of an aircraft construction. However, the application study of the linear shaped charge cutting technology on magnesium alloy components is basically blank. In response to the demand for the linear separation of magnesium alloys, the Mg-12Gd-0.5Y-0.4Zn alloy is selected to carry out the target shaped charge cutting test. The effects of the shaped charge line density, cutting thickness, and mechanical properties on the cutting performance of the alloy are studied. The shaped charge cutting mechanism is analyzed through the notch structure. The results show that the linear shaped charge cutting performance is significantly affected by the penetration and the collapse. The higher the linear density is, the stronger the ability of the linear shaped charge cutter is, and the greater the penetration depth is, which is advantageous. However, the target structure will be damaged when it is too large (e.g., 4.5 g?m-1). Within 12 mm, when the cutting thickness of the target increases, the penetration depth increases. The lower the tensile strength is, the greater the penetration depth is, and the more conducive the penetration depth to the shaped charge cutting is. When the elongation (EL) increases to 12%, the collapse of the target is incomplete and the target cannot be separated. When the tensile strength of the Mg-Gd-Y-Zn alloy is less than 350 MPa, the EL is less than 6.5%, the cutting thickness is less than 12 mm, and the linear shaped charge cutting of the magnesium alloy can be achieved stably.     

Comparison of magnetic flux tube and cosmic string behavior in Kerr metric

Cosmic strings are topological defects which were generated at a transition phase of the very early Universe and are probably responsible for large-scale structure forming. However, they may pull through all history and exist in the recent epoch. Thus, they can have influence for the recent Universe interacting with different objects. We consider the cosmic string behavior in the vicinity of a spinning black hole by means of a numerical simulation. Here we present preliminary results of this work via a comparison of cosmic string and magnetic flux tube behavior in the Kerr metric. Such an approach follows from the similarity of the equations which describe these objects. Therefore, many aspects of this behavior may be comparable.     

太阳极区低日冕重离子的回旋波加热机制

采用电子、质子、氦核和另外一种微量离子代替氧离子的4组元模型分别计算了Fe^11 ,Mg^9 ,Mg^7 ,Ne^7 和Si^7 等微量离子的漂移速度和温度，并和SUMER的观测结果进行了比较。     

有机废水对光催化还原Cr(VI)的影响

采用溶胶-凝胶法制备TiO2光催化剂,在紫外灯照射下研究不同类型的有机废水对Cr(VI)的光催化还原影响。结果表明:延长反应时间并不能大幅度提高Cr(VI)的还原率;当pH=2.7时,Cr(VI)的还原率最好;苯酚添加量控制在反应液体积5%以下为宜;添加三种有机废水的反应结束后,放置于自然状态下,均表现出对Cr(VI)后续的还原能力,在三种有机废水中,最适宜的Cr(VI)空穴捕获剂是垃圾渗滤液。     

The non-linear behavior of the black hole system GRS 1915+105

The Black hole system GRS 1915+105 exhibits various types of long term variability. Here we show that this behavior can be explained in terms of a deterministic non-linear system. In particular, evidence is provided for a non-linear deterministic limit cycle origin of the low frequency QPO exhibited by this source.     

孔强化对7050铝合金残余应力分布的影响

采用开缝衬套冷挤压工艺对飞机用7050铝合金进行挤压强化,针对不同挤压量及铰削量对孔边残余应力分布的影响进行对比,分析得到挤压量及铰削量与残余应力分布的关系.研究表明:采用冷挤压孔强化技术可以改善孔边应力分布,形成有利的残余压应力层.强化后铰孔会减弱残余压应力,对于φ6mm孔铰削量应控制在0.16mm范围内.残余压应力随强化量的增加而增大,5％的挤压量残余压应力值最大达到-276MPa.     

Solar wind origins in coronal holes and in the quiet Sun

Coronal hole (CH) and the quiet Sun (QS) are considered to account for sources of fast and slow solar wind streams, respectively. The differences between the solar wind streams flowing out from the CH and the QS are thought to be related with different plasma generation and acceleration mechanisms in the respective source regions. Here we review recent studies on the solar wind origin in the CH and the QS, compare the possible flow geometries and magnetic structures in these two kinds of solar regions, and summarize the physics associated with two different origin scenarios.     

Testing the no-hair theorem with observations of black holes in the electromagnetic spectrum

According to the no-hair theorem, astrophysical black holes are uniquely described by their mass and spin. In this paper, we review a new framework for testing the no-hair hypothesis with observations in the electromagnetic spectrum. The approach is formulated in terms of a Kerr-like spacetime containing a quadrupole moment that is independent of both mass and spin. If the no-hair theorem is correct, then any deviation from the Kerr metric quadrupole has to be zero. We show how upcoming VLBI imaging observations of Sgr A∗ as well as spectroscopic observations of iron lines from accreting black holes with IXO may lead to the first astrophysical test of the no-hair theorem.     

Short term topological changes of coronal holes associated with prominence eruptions and subsequent CMEs

We study the short-term topological changes of equatorial and polar coronal hole (CH) boundaries, such as a variation of their area and disintegration, associated to reconnection with nearby (within 15° distance) quiescent prominence magnetic fields leading to eruptions and subsequent Coronal Mass Ejections (CMEs). The examples presented here correspond to the recent solar minimum years 2008 and 2009. We consider a temporal window of one day between the CH topological changes and the start and end times of prominence eruptions and onset of CMEs. To establish this association we took into account observational conditions related to the instability of prominence/filaments, the occurrence of a CME, as well as the subsequent evolution after the CME. We found an association between short-term local topological changes in CH boundaries and the formation/disappearance of bright points near them, as well as, between short-term topological changes within the whole CH and eruptions of nearby quiescent prominences followed by the appearance of one or more CMEs.     

层板椭圆孔自由边缘效应

 复合材料层板的直边和圆孔自由边缘效应的三维应力分析,国内外已有不少的数值解和近似解析解。Rybicki等提出了各向异性板椭圆孔2维问题变换为圆孔问题的方法,本文论证了这种变换方法的3维情形,从而可根据圆孔自由边缘效应结果来估计椭圆孔自由边缘效应。