自紧式K形金属密封组件密封特性研究

K形金属密封是液氧/煤油发动机液氧管路系统中经常使用的金属密封结构,其密封性能关系着发动机能否可靠工作.针对自紧式K形金属密封组件,采用非线性有限元方法,基于局部理想粗糙度等效简化,研究了密封机理.仿真结果再现了密封接触面的形成模式,论证了“压力自紧式”密封特征和可重复使用特性,并以密封接触面积和平均接触应力为指标,获得了密封性能与拧紧力矩的敏感性关系.     

A novel method for solving shortest tool length based on compressing 3D check surfaces relative to tool postures

Solving the shortest tool length quickly under a known tool trajectory in multi-axis machining of complex channel parts is an urgent problem in industrial production. To solve this problem, a novel and efficient method is proposed which is featured by extracting only a few necessary curves from the check surface instead of sampling the entire surface. By rotating and compressing the 3D check surface relative to all tool postures, the boundaries of the area occupied by the 2D compressed surfaces are the essential elements for determining the shortest tool length. A tracking-based numerical algorithm is introduced to efficiently solve the silhouette curves which are formed in compressing. To define the multi-taper shaped tool holding system (THS) which is commonly used in production, a characterization model for THS profile is established. A model for solving the shortest tool length is finally constructed based on the critical interference relationship between the THS profile and all compressed boundary curves. For acceleration, the boundary splines are segmented according to their knot vectors. Then a new concept called the axis-aligned tool length box (AATB) is introduced, which can provide a conservative range of tool length for a spline segment. By scanning the AATBs of all spline segments, the very few effective spline segments that may ultimately determine the shortest tool length are filtered out. This acceleration method makes the solution for the shortest tool length more focused and efficient. The results of experimental examples are also reported to validate the efficiency and accuracy of the proposed algorithm.     

热气机活塞十字头摩擦学与动力学的耦合分析

为了研究热气机活塞十字头结构摩擦学及动力学特性,在三维形貌测量的基础上进行连接副的接触分析,得到了其连接副摩擦学特性,建立了耦合摩擦学特性的热气机活塞组动力学模型.对比分析了计算结果与实测值,结果表明:热气机不同工况下其主密封摩擦功耗的计算值与试验值的误差不超过10％,验证了摩擦学计算和建模方法的正确性.当二阶运动较为...     

变形翼面内变形的研究现状及关键技术

变形机翼作为未来飞机设计的重要发展方向之一，其机翼面内变形的研究已得到广泛的关注。本文分别从变展长、变掠角、变弦长、组合变形四个方面进行分析，阐述面内变形机翼的国内外研究现状，归纳总结变形机理及优缺点，分析其发展趋势。针对该领域的研究现状以及变形机翼的应用要求，提出变形机翼亟待解决的关键技术，包括变形蒙皮技术、变形机构、智能驱动器、传感器及控制网络，阐述各关键技术的应用要求，分析其现存问题，并对未来发展方向进行归纳；以期为面内变形机翼的设计和应用实现提供部分参考。     

Improving aircraft aerodynamic performance with bionic wing obtained by ice shape modulation

For Unmanned Aerial Vehicles (UAVs) with limited electrical power to achieve effectively anti-/de-icing at the leading edge of the wing, a strategy of ice shape modulation was proposed. Isolated simulated ice shape pieces printed by 3D printing technology are mounted on a NACA0012 finite wing model, and its lift/drag coefficients and suction-side velocity fields are measured by the six-component force balance and the Particle Imaging Velocimetry (PIV), respectively. The ratio of the spanwise length of a single ice shape piece to chord length and the spanwise length of the non-icing area between the two adjacent single ice shape pieces are defined as dimensionless ice shape length (w/c) and dimensionless modulation ratio (w/λ), respectively. The results indicate that for a fixed w/λ, the wing lift coefficient first increases and then drops with increasing w/c, and a peak value exists when w/c is between 0.1 and 0.2. The lower the w/λ is, the higher the wing lift coefficient will be. The periodical variation of the flow separation area along the spanwise direction is attributed on the one hand to the acceleration effect of the flow field in the non-icing area which reduces the separation area, and on the other hand to the cross-flow caused by the streamwise vortices from the non-icing area to the icing area which promotes the mixing of the flow field (similar to vortex generators). The obtained modulation law is verified through flight tests and provides guidance for the use of ice shape modulation scheme for UAVs that cannot be completely anti-/de-icing under severe weather conditions.     

光纤环非互易相位误差尾纤补偿方法研究CSCD

针对光纤环的热致非互易误差的补偿方法进行研究,并通过仿真分析与实验验证,证明了某种光纤环尾纤长度与光纤环热致非互易误差之间的关系。根据等效介质理论和Mohr理论,建立了光纤环热致非互易相位误差仿真分析模型,并利用该模型计算了不同温度环境条件下,某类型光纤环顺逆时针方向光纤长度发生变化时,陀螺仪输出的全温零位漂移的变化量。仿真及实验结果表明,在1℃/min温变速率条件下,总长约800m的光纤环圈顺逆时针方向光纤长度相差约0.5m时,光纤环全温零位漂移量缩小了0.4(°)/h。研究结果得出了针对此类型的光纤环,当光纤环尾纤每减少0.5m,其热致非互易相位误差减小0.4(°)/h的规律。该项研究成果为后续优化光纤环的全温精度奠定了基础。     

基于改进狼群算法的多无人机协同多目标分配CSCD

针对现代空战多无人机协同多目标任务分配问题,结合标准狼群算法,提出了一种改进狼群算法的多目标任务分配方法。根据狼群的不同分工以及搜索属性,建立了基于自主游走机制的头狼产生规则、基于多策略知识库的探狼游走机制和基于自适应步长的猛狼奔袭及围攻方式,从而对传统狼群算法的随机性进行智能化约束与控制,以解决多无人机协同多目标任务分配问题。数值仿真结果表明,该方法能够快速有效获得任务分配方案,避免陷入局部最优。