高温合金微量润滑振动钻削温度与刀具磨损

为了解决高温合金钻削温度高、刀具磨损快的问题,采用微量润滑的振动钻削加工方法,从换热机制角度对振动钻削的降温机理进行分析,并进行振动钻削和普通钻削对比实验.结果表明:微量润滑普通钻削的最高测量温度达到了110℃且温度随钻削深度、钻孔个数的增加而升高,而振动钻削的测量温度为55℃左右且随削深度、钻孔个数的增加增长缓慢;普通钻削刀具磨损量达到0.5 mm且随钻孔个数的增加磨损加剧,振动钻削刀具磨损量只有0.22 mm且磨损量增加缓慢.     

基于CAM/CNC集成的航空大型薄壁件数控加工在机刀轨调整方法

航空大型薄壁零件刚性弱,加工过程中易产生超差变形,需要对零件进行在机检测,并将检测数据反馈给CAM系统进行拟合并调整刀轨。以上过程需要在不同部门和系统间进行切换,严重影响了生产效率。针对以上问题,提出了一种基于CAM/CNC集成的航空大型薄壁件数控加工在机刀轨调整方法。建立了CAM/CNC集成框架,并构建了用于CAM/CNC间信息传递的动态特征信息模型,基于CAM系统离线生成特征理论中间状态,基于CNC系统建立特征实际中间状态检测点同理论中间状态的映射关系。通过分析理论厚度和实际厚度,确定特征中间状态的变形情况。针对变形导致特征中间状态加工余量无法包络符合公差要求的最终加工状态的情况,进行在机刀轨调整。基于所提出的方法开发的航空大型薄壁件数控加工在机刀轨调整系统在某大型航空企业得到了应用验证,可有效避免信息的反复传递,减少了工艺人员的重复劳动,提高了生产效率。     

数控加工常用对刀方法及其应用

阐述数控铣削加工技术中几种典型对刀操作方法,对在对刀过程中主要功能模块做概述性的描述,并对它在数控程序编程中的应用进行介绍。     

改善机床运动的五轴刀轨光顺方法

建立了五轴数控加工刀轨光顺优化模型,改善了线性插补方式下拐角过渡运动中的机床加速度情况。考虑了5个轴加速能力的差异,以轴加速度比,即轴实际达到的最大加速度与其允许最大加速度的比值,来衡量轴的加速度情况,以5个轴加速度比的平方平均数在整体上衡量机床的加速度情况,降低该值可提高机床运动平稳性。采用最短距离线法在初始刀轨的各切触点处建立了刀轴偏航角和俯仰角的可行域,使光顺后的刀轨满足残高和无过切要求。实例表明:该方法可有效光顺五轴数控加工刀轨,改善机床加速度情况,提高机床运动平稳性。      

Characterization and life prediction of single-pass honing tool for fuel injection nozzle

Single-pass honing is an important machining method for finish machining of holes, which can meet the requirement for high efficiency and consistency of holes. Characterization and life prediction of single-pass honing tool are necessary to improve the machining accuracy of holes honed, especially dimension accuracy. Single-pass honing tool is a single layer abrasive tool with fixed dimension, which still remains problematic for characterization and life prediction. For fuel injection nozzles with bore diameter under 1 mm, the stiffness of the single-pass honing tool is poor. This article presents a novel analytical model that predicts life of the tool with poor stiffness. Firstly, according to the bore diameter and dimension tolerance, the single-pass honing tool is designed and manufactured. Based on the prepared single-pass honing tool, the measurement and characterization methods are established. Furthermore, the tool wear tests are carried out, and the tool contour evolution model is established to predict the tool life.     

Effects of traverse speed on weld formation,microstructure and mechanical properties of ZK60 Mg alloy joint by bobbin tool friction stir welding

ZK60B (Mg-6% Zn-0.6% Zr) alloy joints fabricated by bobbin tool friction stir welding (BTFSW) with various traverse speeds were investigated. The sound joint fabricated by the BTFSW was possible under the appropriate welding parameters. The severe plastic deformation during BTFSW resulted in dispersion and segregation of the Zr-rich particles within the stirred zone (SZ) followed by evolution of a bimodal grain structure with distributed bands of 0.8–1.7 μm ultrafine grains and 4.1–7.1 μm equiaxed grains. Micro-hardness of SZ is substantially reduced in contrast to that of parent metal (PM) in spite of the finer grain size owing to dissolution of Mg-Zn based precipitates having hardening effects on alpha-Mg matrix. With the decrease in traverse speed, randomization degree of the plasticized metal flow increases, which is evidenced by the randomized arc line pattern at the low traverse speed. Among all defect-free joints, the 200 mm/min joint exhibits the weakest isotropy of texture within SZ and the best tensile properties, which has reduced ultimate tensile strength and yield strength by 5.4% and by 22.2%, respectively, as compared to the PM. The randomized texture hinders the joint fracturing within SZ at low elongation. Therefore, a relatively high elongation of 10.8% was achieved, which corresponded to 72% of the PM value.     

数控车削加工刀尖圆弧半径补偿技术分析与应用

本文分析了数控车削中刀尖圆弧半径对加工精度影响,得出其误差计算方法;阐明数控系统在数控车削加工过程中刀尖圆弧半径补偿原理,指出编程中注意的问题,以保证加工精度。     

航空模具数控刻线高效工具——柔性数控刻线器

分析了航空模具高效、精密刻线的重要性及传统刻线方法、刻线工具存在的问题,介绍了一种精密、高效数控刻线工具--柔性数控刻线器的结构、原理、使用方法等.     

基于普通车床的微V型槽飞切装置分析与设计

通过对飞刀轴的强度、刚度和振动模态的分析,设计制作了基于普通车床的飞切装置.并采用PCD成形车刀在铝材料上进行了飞切加工V型槽的实验.测试结果证明了该飞切装置的可用性,为生产实践提供了必要的技术参考与装备,并为进一步分析飞切理论打下了基础.