汽心泵特性研究

 通过理论分析和试验,导出汽心泵稳定工作的基本方程和性能参数之间的函数关系;分析了当转速、压力、流量和负载系数变化时,汽心对泵特性所起的调节作用;提出决定相对汽心直径的特征参数p_2/n~2D_2~2;还讨论了汽心泵的极限工作状态和最大流量调节范围。     

环路热管内工质流动特性的研究

由于环路热管（LHP）具有高传热性能、远距离传输热量、优良的控温特性和管路的可任意弯曲、安装方便等特点，使LHP在航天热控领域有着广泛的应用前景。文章对LHP内工质的流动压力降进行了分析和计算；对毛细芯所能提供的最大蒸发传热能力进行了预测，并结合实验研究综合分析了毛细芯结构对LHP性能的影响。     

Application of improved active disturbance rejection control algorithm in tilt quad rotor

The Tilt Quad Rotor (TQR) has complex dynamics characteristics, especially in conversion mode. It is difficult to build the dynamic model of the TQR and the environmental factors have a great influence on it. To solve the problem of control in conversion mode of TQR, this paper carries out the design of the controller based on improved Active Disturbance Rejection Control (ADRC). According to the characteristics of flight in conversion mode, Tracking Differentiator (TD) with explicit model is used to solve the problem of multiple integrals when the system is high-order system. Extended State Observer (ESO) with Radial Basis Function (RBF) neural network is used to estimate and compensate for internal and external uncertainties, and the adaptive sliding mode control in Nonlinear State Error Feedback (NLSEF) is used to improve the response speed of the controller and reduce the parameters which should be tuned. Through the flight control simulation of the TQR, the validity and rationality of the control system are verified.     

可控曲率半径的圆柱形叶片逐点绘型方法

针对中低比转速离心泵,根据叶片进出口边界条件,以逐点绘型方法为基础,提出了一种新的曲率半径可控的叶片绘型方法。该方法的主要特点是曲率半径比值可作为设计常量由设计人员根据需要事先给定,随后分析了曲率半径及比例因子对叶片安放角、叶片包角、相对速度及速度矩等的影响。结果表明,不同曲率半径比值下的叶型参数及流动参数变化范围很大,曲率半径比值较大时,节流损失较大,泵扬程较低,曲率半径比值较小时,脱流损失较大,泵效率较低,存在较优的曲率半径比值区间[1.4,2.4],使叶片安放角平滑变化,泵的综合性能较优,在该优化区间内,取较大的曲率半径比值有利于获得较优的汽蚀性能,比例因子为0时叶片安放角的变化较为平稳,可用于开展离心泵的初步设计。     

采用霍尔传感器的旋翼频率采集设计

为达到对旋翼飞机的控制,需要对旋翼转速进行采集.霍尔转速传感器以其高可靠性等优点常被用来测量转速.介绍了一种使用霍尔传感器进行旋翼转速采集系统,包括硬件构架,逻辑采集单元和软件设计,并给出了优化策略;通过试验数据分析,采集精度达到了预期.     

ENERGY-SAVING MATCHING STRATEGY AND EXPERIMENTAL STUDY OF PUMPING SYSTEM FOR TRUCK-MOUNTED CONCRETE PUMP

Aiming at the high fuel consumption and use-cost of truck-mounted concrete pump , an energy-saving matching strategy of pumping system is presented and the experimental study is conducted.Since pumping system occupies most resources of engine , the matching strategy between engine and main pump is analyzed to meet the load demand and reduce the engine rational speed drop.The testing method is established to measure the fuel consumption of engine under various working conditions , and the experimental data are analyzed to find the law of the fuel consumption of engine.The system performance can be improved by adjusting the system input value.Finally , the energy-saving matching strategy is established to reduce the fuel consumption of truck for unit workload , which provides a new approach for the energy-saving of truck-mounted concrete pump.     

离散粗糙元诱发边界层转捩的实验研究

针对直升机转子叶片模型表面离散粗糙元诱发边界层转捩问题开展了实验研究,分析不同雷诺数下粗糙元尺寸参数对转捩位置的影响。实验在中航工业气动院直升机转子叶片模拟装置进行,在模型转子叶片表面布置不同尺寸的离散柱状粗糙元,利用红外热像技术探测边界层转捩,并提出一种基于湍流／层流区域面积比的转捩位置判定准则,目的是实现边界层转捩位置自动识别,进而分析粗糙元尺寸参数对转捩位置的影响。实验转速为300至600 r／m,对应叶尖切向速度为25～40 m／s。实现了对旋转叶片边界层转捩位置的定量测量,通过实验验证,转捩位置判定算法正确可靠,初步得到了不同高度 DRE 诱发转捩位置与雷诺数之间的关系,随着粗糙元高度的增加,转捩位置逐渐靠前。     

跨声速串列转子失速机制的数值研究

为了解决跨声速串列转子的低裕度问题,就必须了解跨声速串列转子的流场结构与失速机制.设计了叶尖切线速度为450m/s,负荷系数为0.56的高负荷跨声速串列转子.基于数值模拟的结果,分析了该串列转子在0.5mm叶尖间隙下的叶尖流场结构与失速机制,并在此基础上分别探讨了叶尖间隙和前、后排叶片周向位置对串列转子特性的影响和失速机制的变化.结果表明:前排叶片的叶尖区域是 影响串列转子稳定性的关键;随着叶尖间隙的增加,串列转子的失速机制也发生变化,从前排叶片叶尖区域的尾迹与径向潜流堵塞后排叶片通道转变为前排叶片叶尖泄漏流堵塞;在较大周向相对位置(后排叶片压力面周向远离前排吸力面)的情况下,串列转子获得最好的效果,随着周向相对位置(PP)的增加,失速部位从后排叶片转移至前排叶片.      

温度对飞机燃油射流泵工作特性影响

建立了射流泵数学模型,采用数值计算方法对其工作特性进行了模拟,搭建了实验台,采用RP-3燃油,通过实验数据验证了模型的正确性.在此基础上,分别选择了RP-3和JET-A两种燃油,计算了从-40℃~40℃温度下,不同操作压力对射流泵流量比的影响.结果表明:燃油温度高于0℃时,温度对射流泵工作特性影响并不明显,随着温度的降低,射流泵性能与标准温度下（20℃）偏差越来越大,且压比越高此偏差越明显.当温度高于0℃时,采用RP-3和JET-A燃油性能相差不大,RP-3燃油性能略优于JET-A燃油,但是在低温下,RP-3燃油性能远高于JET-A燃油.因此当燃油温度较低且压比较高时,必须充分考虑温度对射流泵特性的影响.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.