直升机后缘襟翼驱动器迟滞现象仿真与抑制

直升机后缘襟翼多采用压电驱动器作为驱动元件，但是在使用过程中压电驱动器迟滞会对其振动控制性能产生不利影响，因此针对压电驱动器迟滞开展了迟滞建模与抑制研究。通过实验研究了压电驱动器在不同驱动频率下的迟滞特性，采用Bouc-Wen模型对驱动器迟滞现象进行了建模，并采用粒子群算法（PSO）辨识模型参数，与实际测量迟滞曲线进行了对比，在10~60 Hz范围内所建立的迟滞模型能够较为精确地描述压电驱动器迟滞现象。建立了基于Bouc-Wen逆模型的前馈补偿控制与PID反馈控制相结合的复合控制策略，实验结果显示该控制策略能够在10~60 Hz较宽的频率范围内有效抑制该压电驱动器迟滞现象。建立了考虑驱动器迟滞的主动控制后缘襟翼振动控制动力学模型，并对中等速度稳态前飞条件下后缘襟翼振动控制性能进行了仿真，仿真结果显示驱动器迟滞会在一定程度上削弱振动控制性能，而采用复合控制可以提高后缘襟翼旋翼振动控制性能。     

Carrier phase prediction method for GNSS precise positioning in challenging environment

Since the signals of global navigation satellite system (GNSS) are blocked frequently in challenging environments, the discontinuous carrier phases seriously affect the application of GNSS precise positioning. To improve the carrier phase continuity, this paper proposes a carrier phase prediction method based on carrier open-loop tracking. In the open-loop tracking mode, the carrier numerically controlled oscillator (NCO) is controlled by the predicted Doppler, but not by the loop filter output. To improve the phase prediction effective time, accurate receiver clock drift estimation is studied in the prediction method. The phase prediction performance is tested on GNSS software receiver. In the phase prediction effective time tests, open-loop processes were set for the tested channel. The test results show that, when some satellite signals are blocked in 15?s, the probability of carrier phase error less than quarter cycles is more than 94%. In the real time kinematic (RTK) positioning tests, some satellite signals are blocked in 10–15?s repeatedly. The test results show that, the carrier phase continuity is basically not affected by the signal interruption, and the RTK can almost keep continuous centimeter-level positioning accuracy without re-fixing the integer ambiguity.     

A novel control method for turboshaft engine with variable rotor speed based on the Ngdot estimator through LQG/LTR and rotor predicted torque feedforward

In order to compensate for the disturbance of wide variation in rotor demanded torque on power turbine speed and realize the fast response control of turboshaft engine during variable rotor speed, a cascade PID control method based on the acceleration estimator of gas turbine speed (Ngdot) and rotor predicted torque feedforward is proposed. Firstly, a two-speed Dual Clutch Transmission (DCT) model is applied in the integrated rotor/turboshaft engine system to achieve variable rotor speed. Then, an online estimation method of Ngdot based on the Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR) is proposed for power turbine speed cascade control. Finally, according to the cascade PID controller based on Ngdot estimator, a rotor demanded torque predicted method based on the Min-batch Gradient Descent-Neural Network (MGD-NN) is put forward to compromise the influence of rotor torque interference. The simulation results show that compared with cascade PID controller based on Ngdot estimator and the one combined with collective pitch feedforward control, the novel control method proposed can reduce the overshoot of power turbine speed by more than 20%, which possesses faster response, superior dynamic effect and satisfactory robustness performance. The control method proposed can realize the fast response control of turboshaft engine with variable rotor speed better.     

航空发动机低压转子系统的“可容模态”设计及实验验证

建立了带弹性支承和阻尼器的航空发动机低压柔性转子动力学模型,进行了模态计算以及临界转速处的响应计算。在考虑临界转速约束与“临界跟随”现象约束的条件下,综合模态不平衡影响因子、弹支应变能占比以及套齿连接结构稳定性构造了可容度评价函数,建立了低压转子系统的“可容模态”优化设计方法。设计并搭建了低压转子实验系统,从模态测试实验、阻尼器减振实验以及长时间“共振”实验,验证了设计方法的可靠性。研究结果为计算的临界转速与实际测量的临界转速最大误差为3.86%,阻尼器在1阶与2阶临界转速处的减振比最大可达45.6%,实验转子系统在1阶与2阶临界转速处各完成了长达412.5 s和429.8 s的“共振”实验,共振过程中转子系统各通道振动单峰值稳定在100μm以内,且无次谐波产生。表明了所建立的航空发动机低压转子系统“可容模态”优化设计方法是可行的。     

涡轮动叶表面换热特性的试验研究

航空发动机性能的提高对涡轮叶片耐热极限提出了更高的要求,为了更准确地分析涡轮叶片的传热特性,选取某型气冷涡轮动叶10%、50%和90%叶高的特征型面通过低导热光敏树脂材料经过3D打印而成,通过叶片表面粘贴厚度为0.02mm康铜加热膜接通恒定电流加热,使用红外热像系统精确测量叶片壁面温度,在平面叶栅中研究了吹风比(M)和雷诺数(Re)对气膜绝热冷却效率和努塞尔数(Nu)的影响(试验中基于弦长的进口雷诺数Re为8.0×10⁴-16.7×10⁴,吹风比M为1-3)。试验结果表明：M=1时气膜能够较好附着在叶片表面,叶片表面得到较好冷却;随着主流雷诺数的增加,绝热壁面温度逐渐升高,绝热效率逐渐降低;吹风比对涡轮叶片的传热特性的影响与气膜孔出流角度有关,随着吹风比的增大,压力面绝热冷却效率逐渐增大,由于吸力面的气膜孔出流角较大,吹风比增大使得吸力面的绝热冷却效率逐渐减小;随着吹风比的增加,对流换热系数增大。     

机匣沟槽对微型轴流涡轮叶尖泄漏流动的影响

本文通过对某微型涡喷发动机的单级轴流式涡轮进行机匣设计,采用剪切应力输运(SST)模型求解定常黏性雷诺平均Navier-Stokes方程,研究了不同机匣沟槽结构对其叶尖泄漏流动的影响。计算结果说明：当全机匣沟槽结构的叶顶浸入沟槽即d/c＞1.0时,封严效果较好;相较于全机匣沟槽结构,后开式机匣沟槽结构的封严效果更好, 随着沟槽前缘间隙的增大,封严效果减弱;沟槽深度a/c=1时,封严效果最佳,即泄漏流明显减弱,同时效率减小量较小。     

太阳活动对VLF传播的一种影响

本文以实验数据为基础, 讨论了在太阳耀斑期间产生的相位周期丢失, 并用对极传播理论解释了这种相位周期丢失的机理。相位周期丢失是电波传播中的一个重要传播现象, 特别是对于低频和甚低频传播。由于太阳耀斑引起的这一传播现象在以往的讨论中比较罕见, 因此, 对这一问题的讨论具有特殊意义。      

面向设计的复合材料旋翼桨叶动力优化设计

提出一种面向设计的复合材料旋翼桨叶结构动力优化方法。采用典型剖面设计、变量连接、铺层变量连续化等方法,有效地处理了剖面内部形状、复合材料铺层、配重质量３类设计变量。在动力分析模型中考虑了剖面翘曲、耦合变形和陀螺力的影响,由三级数值计算模式实现固有频率灵敏度分析。约束条件包括了固有频率、结构重量、自转惯量等设计要求,优化求解采用基于序列二次规划的算法。上述方法真实反映了桨叶结构特征和实际工程设计要求。     

电子移相方法的讨论

对精密测试中常用的几种移相方法进行了讨论,主要浅析小角度电路移相方法。     

一种数字化DS/BPSK扩频接收机

介绍一种新型数字化DS/BPSK(Direct Spread/Binary Phase Shife Keying)扩频接收机的设计.该接收机采用专用数字相关器为核心的硬件设计,并结合数字处理算法完成扩频信号的解调.技术上采用串并组合的伪码捕获、科斯特环载波跟踪、延迟锁定环伪码跟踪等方式,可通过软件算法灵活实现.该接收机具有综合性能强,及软件接口灵活的特点,可有效地应用于基于码分多址的多目标测控系统中.