M数缩尺法旋翼颤振动力相似模型设计

本文以延-2复合材料桨叶旋翼为例,用M数缩尺法尝试设计了缩尺比为1/5的颤振相似模型。设计从旋翼颤振微分方程开始,应用π定理得出10个独立相似准则数,列出各有关物理量缩尺因子后进行模型结构设计,从而得出了若干有益的结论。     

Lift coefficient prediction at high angle of attack using recurrent neural network

In this paper, identification of dynamic stall effect of rotor blade is considered. Recurrent Neural Networks have the ability to identify the nonlinear dynamical systems from training data. This paper describes the use of recurrent neural networks for predicting the coefficient of lift (C_Z) at high angle of attack. In our approach, the coefficient of lift (C_Z) obtained from the experimental results (wind tunnel data) at different mean angle of attack θ_mean is used to train the recurrent neural network. Then the recurrent neural network prediction is compared with experimental ONERA OA212 airfoil data. The time and space complexity required to predict C_Z in the proposed method is less and it is easy to incorporate in any commercially available rotor code.     

Numerical study on flow fields and aerodynamics of tilt rotor aircraft in conversion mode based on embedded grid and actuator model

A method combining rotor actuator disk model and embedded grid technique is presented in this paper, aimed at predicting the flow fields and aerodynamic characteristics of tilt rotor aircraft in conversion mode more efficiently and effectively. In this method, rotor's influence is considered in terms of the momentum it impacts to the fluid around it; transformation matrixes among different coordinate systems are deduced to extend actuator method's utility to conversion mode flow fields' calculation. Meanwhile, an embedded grid system is designed, in which grids generated around fuselage and actuator disk are regarded as background grid and minor grid respectively, and a new method is presented for ‘donor searching' and ‘hole cutting' during grid assembling. Based on the above methods, flow fields of tilt rotor aircraft in conversion mode are simulated, with threedimensional Navier–Stokes equations discretized by a second-order upwind finite-volume scheme and an implicit lower–upper symmetric Gauss–Seidel(LU-SGS) time-stepping scheme. Numerical results demonstrate that the proposed CFD method is very effective in simulating the conversion mode flow fields of tilt rotor aircraft.     

转子-支承耦合结构的模型修正研究

在转子-支承耦合结构的动力学分析过程中,结构模态参数计算结果与实验测试结果往往存在较大差异。针对此问题,应用优化算法对结构动力学模型进行修正,使计算模型能更准确地反映结构特性。建立由梁单元、盘单元、弹性支承单元组成的结构动力学有限元模型;选择优化目标函数、设计参数,并对各参数进行灵敏度分析。应用粒子群算法对选取的设计参数进行优化,得到最优模型。利用转子-滚动轴承实验器进行验证,结果表明,方法能够有效地实现转子-支承耦合结构的动力学模型修正,修正后模型更接近实际结构。     

基于面板数据模型的中西部地区加工贸易升级研究

我国经济高速发展,劳动力、土地等要素随之发生转变,加工贸易从东部地区向中西部地区转移,中西部地区加工贸易急需升级以适应发展。利用2001-2011年中西部地区部分省份的面板数据建立计量模型,通过检验对混合估计模型、固定效应模型和随机效应模型进行选择,并对选定模型的估计结果进行具体分析,提出中西部地区加工贸易升级的对策及建议。     

舰载直升机金属动部件寿命控制技术研究

在分析现役老龄化舰载直升机动部件载荷特点的基础上,结合直升机所处的海洋腐蚀环境,讨论了舰载直升机的损伤类型和损伤容限寿命管理方法在其寿命分析中的应用,比较了损伤容限法应用于舰载直升机动部件与应用于固定翼飞机的不同点,重点讨论了损伤容限方法应用于工程实践亟待解决的关键技术。     

基于转子初始不平衡量控制的整机振动排故方法

针对某型航空发动机试车低压振动超限问题,结合发动机的结构特点,进行了故障分析。通过改进转子的平衡工艺,提出了控制转子初始不平衡量从而抑制发动机临界转速振动大的排故方法,再次试车时发现振动水平良好。结果表明排故方法有效,对今后发动机装配和整机振动排故具有重要的参考价值。     

ANALYSIS OF AN ELECTROSTRICTIVE STACK ACTUATOR FOR ACTIVE TRAILING EDGE FLAPS

Helicopter is a complex dynamic system withmany rotating components. The rotor blades oper-ate in a highly complex aerodynamic environment.The vibratory hub load,which is caused by cyclicvariation ofcentrifugaland aerodynamic load of therotating bladesin flight,is transmitted to the fuse-lage,resulting in serious vibration and noise of thestructure. It is one of the most important excitingsources in helicopters.There has long been a desire to reduce heli-copter vibration and to improve its per…     

套齿连接转子简化建模及动力特性分析

在进行转子和整机计算时建立套齿结构接触模型会增加计算量，降低计算效率，直接将套齿结构省略又无法体现其刚 度特性变化对转子动力特性的影响。针对该问题，基于航空发动机单圆柱面套齿连接的结构和力学特征，建立了考虑构件间界面 接触状态的力学特征分析模型，提出了考虑套齿结构刚度随参数变化的简化建模方法，并与套齿接触模型进行了对比分析。建立 了单圆柱面套齿连接结构转子简化模型，开展了相应的转子动力特性试验，对比分析了拧紧力矩对转子模态频率的影响。结果表 明：转子简化模型与试验模型最大计算误差小于5%，证明套齿结构简化建模方法具有较高的可靠性和准确性，可为工程实践中高 效开展含套齿结构转子及整机动力学准确计算分析提供方法与参考。     

用神经网络法编程加工轮毂上特殊曲面的探讨

根据轮毂上曲面的特殊性,提出了采用神经网络方法进行编程,实现数控加工,以取代传统的加工方法的设想。