跨声速串列转子失速机制的数值研究

为了解决跨声速串列转子的低裕度问题,就必须了解跨声速串列转子的流场结构与失速机制.设计了叶尖切线速度为450m/s,负荷系数为0.56的高负荷跨声速串列转子.基于数值模拟的结果,分析了该串列转子在0.5mm叶尖间隙下的叶尖流场结构与失速机制,并在此基础上分别探讨了叶尖间隙和前、后排叶片周向位置对串列转子特性的影响和失速机制的变化.结果表明:前排叶片的叶尖区域是 影响串列转子稳定性的关键;随着叶尖间隙的增加,串列转子的失速机制也发生变化,从前排叶片叶尖区域的尾迹与径向潜流堵塞后排叶片通道转变为前排叶片叶尖泄漏流堵塞;在较大周向相对位置(后排叶片压力面周向远离前排吸力面)的情况下,串列转子获得最好的效果,随着周向相对位置(PP)的增加,失速部位从后排叶片转移至前排叶片.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

Nonlinear dynamic modeling of a helicopter planetary gear train for carrier plate crack fault diagnosis

Planetary gear train plays a significant role in a helicopter operation and its health is of great importance for the flight safety of the helicopter. This paper investigates the effects of a planet carrier plate crack on the dynamic characteristics of a planetary gear train, and thus finds an effec-tive method to diagnose crack fault. A dynamic model is developed to analyze the torsional vibra-tion of a planetary gear train with a cracked planet carrier plate. The model takes into consideration nonlinear factors such as the time-varying meshing stiffness, gear backlash and viscous damping. Investigation of the deformation of the cracked carrier plate under static stress is performed in order to simulate the dynamic effects of the planet carrier crack on the angular displacement of car-rier posts. Validation shows good accuracy of the developed dynamic model in predicting dynamic characteristics of a planetary gear train. Fault features extracted from predictions of the model reveal the correspondence between vibration characteristic and the conditions (length and position) of a planet carrier crack clearly.     

燃料分级对旋流火焰的动态特性影响研究

为深入研究分级旋流火焰特性,以分级旋流模型燃烧室为研究对象,对四个不同燃料分级比(Rf)条件下的分级旋流火焰进行了数值研究,在时均燃烧场特性分析的基础上进一步对燃料分级比为1和3两个工况进行了基于壁面建模的大涡模拟(WMLES)研究。结果表明:燃料分级比的改变会影响中心回流区(CRZ)的长度和宽度。燃烧室中截面的散点分布图能够显示出不同燃料分级比条件下的燃烧特征。燃料分级比为1时,燃烧室剪切层仅存在零散的涡破碎区;而燃料分级比为3时,伴随涡破碎区还出现了单螺旋分支进动涡核(PVC)。通过FFT变换获得的燃烧室内剪切层速度能谱主频与进动涡核的旋转频率相同,表明内剪切层速度脉动的产生与进动涡核有关。另外进动涡核会使流场内的燃料分布和燃烧模式发生周期性的变化,进而影响燃烧过程。调整燃料分级比在1附近,能够使分级火焰达到稳定燃烧降低排放的目标。     

主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

带非线性支撑的转子有限元模型求解方法

用数值方法研究了非线性支撑的柔性转子系统的动学行为,提出了一种将有限元与非线性支撑结合的模型和求解方法。利用有限元法(FEM)构建转轴和转盘部分的模型,通过矩阵进行组合;利用离散元方法对包含滚动轴承和挤压油膜阻尼器(SFD)的支撑部分进行建模,此部分包含4个单元,分别为轴承内圈、外圈、SFD内圈和支撑鼠笼。有限元部分和离散元部分通过轴端节点相连,仿真过程中轴端位移传递给非线性支撑部分,支撑部分通过位移计算得到的非线性力反过来作用于有限元转子轴端部分。为了耦合求解有限元转子和非线性支撑组成的数学模型,提出了一种综合的迭代求解方法,克服传统的有限元求解方法对轴端隐性非线性支撑的求解局限性。由于转轴部分采用了Timoshenko梁单元建模,对比与简单转子模型,可以考虑陀螺力矩和轴的柔性特征,更能体现非线性支撑对振动真实影响。在建立的20个轴单元的有限元转子模型中,非线性响应更多体现在靠近非线性支撑的节点1和节点21处,响应频谱中靠近轴端的节点能体现出滚动轴承的2倍和3倍变柔振动频率。     

转子系统挤压油膜阻尼器设计与动力特性

鉴于挤压油膜阻尼器(SFD)设计必须要同时考虑转子系统的动力学特性,提出了一种转子系统与挤压油膜阻尼器耦合设计方法,给出了详细的设计流程。对所设计的阻尼器进行了CFD数值模拟、油膜压力测量以及减振效果实验,结果证明所提出的设计方法是有效的。相比未采用阻尼器,采用阻尼器后转子系统两个转盘的振幅分别下降了46%和39%。通过实验还研究了不平衡量、支承刚度、供油压力和滑油温度对挤压油膜阻尼器减振效果的影响。结果表明,相比于不平衡量和支承刚度对减振效果的影响,供油压力和滑油温度的影响并不显著。进行挤压油膜阻尼器设计时,重点应该关注转子上的不平衡量大小和支承刚度。     

Fluid structure interaction simulation of supersonic parachute inflation by an interface tracking method

An Arbitrary Lagrangian–Eulerian (ALE) approach with interface tracking is developed in this paper to simulate the supersonic parachute inflation. A two-way interaction between a nonlinear finite element method and a finite volume method is accomplished. In order to apply this interface tracking method to problems with instantaneous large deformation and self-contact, a new virtual structure contact method is proposed to leave room for the body-fitted mesh between the contact structural surfaces. In addition, the breakpoint due to the fluid mesh with negative volume is losslessly restarted by the conservative interpolation method. Based on this method, fluid and structural dynamic behaviors of a highly folded disk-gap-band parachute are obtained. Numerical results such as maximum Root Mean Square (RMS) drag, general canopy shape and the smallest canopy projected areas in the terminal descent state are in accordance with the wind tunnel test results. This analysis reveals the inflation law of the disk-gap-band parachute and provides a new numerical method for supersonic parachute design.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

考虑滑流影响的埋入式进气道气动特性分析与流动控制研究

研究滑流对埋入式进气道性能的影响机理对于发动机的稳定性具有重要意义。针对某型涡桨发动机 滑油散热器进排气道系统,基于 CFD技术建立系统的螺旋桨滑流与滑油散热器内流一体化数值模拟方法,进 行考虑滑流影响的滑油散热系统埋入式进气道气动设计仿真分析;针对埋入式进气道由于吸入边界层低能气 流导致通过散热器流量低的问题,设计4组涡流发生器进行主动流动控制。结果表明:滑流使得进气道中的气 流偏离,难以形成稳定漩涡,容易发生流动分离;而合理设计的涡流发生器可以有效改善埋入式进气道内流场 特性,并使通过散热器的流量提高12%。