Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

带非线性支撑的转子有限元模型求解方法

用数值方法研究了非线性支撑的柔性转子系统的动学行为,提出了一种将有限元与非线性支撑结合的模型和求解方法。利用有限元法(FEM)构建转轴和转盘部分的模型,通过矩阵进行组合;利用离散元方法对包含滚动轴承和挤压油膜阻尼器(SFD)的支撑部分进行建模,此部分包含4个单元,分别为轴承内圈、外圈、SFD内圈和支撑鼠笼。有限元部分和离散元部分通过轴端节点相连,仿真过程中轴端位移传递给非线性支撑部分,支撑部分通过位移计算得到的非线性力反过来作用于有限元转子轴端部分。为了耦合求解有限元转子和非线性支撑组成的数学模型,提出了一种综合的迭代求解方法,克服传统的有限元求解方法对轴端隐性非线性支撑的求解局限性。由于转轴部分采用了Timoshenko梁单元建模,对比与简单转子模型,可以考虑陀螺力矩和轴的柔性特征,更能体现非线性支撑对振动真实影响。在建立的20个轴单元的有限元转子模型中,非线性响应更多体现在靠近非线性支撑的节点1和节点21处,响应频谱中靠近轴端的节点能体现出滚动轴承的2倍和3倍变柔振动频率。     

转子系统挤压油膜阻尼器设计与动力特性

鉴于挤压油膜阻尼器(SFD)设计必须要同时考虑转子系统的动力学特性,提出了一种转子系统与挤压油膜阻尼器耦合设计方法,给出了详细的设计流程。对所设计的阻尼器进行了CFD数值模拟、油膜压力测量以及减振效果实验,结果证明所提出的设计方法是有效的。相比未采用阻尼器,采用阻尼器后转子系统两个转盘的振幅分别下降了46%和39%。通过实验还研究了不平衡量、支承刚度、供油压力和滑油温度对挤压油膜阻尼器减振效果的影响。结果表明,相比于不平衡量和支承刚度对减振效果的影响,供油压力和滑油温度的影响并不显著。进行挤压油膜阻尼器设计时,重点应该关注转子上的不平衡量大小和支承刚度。     

Experimental investigations of the spray structure and interactions between sectors of a double-swirl low-emission combustor

In this paper, the spray characteristics of a double-swirl low-emission combustor are analyzed by using Particle Imaging Velocimetry (PIV) and Planar Laser Induced Fluorescence (PLIF) technologies in an optical three-sector combustor test rig. Interactions between sectors and the influence of main stage swirl intensity on spray structure are explained. The results illustrate that the swirl intensity has great effect on the flow field and spray structure. The spray cone angle is bigger when the swirl number is 0.7, 0.9 than that when the swirl number is 0.5. The fuel distribution zone is larger and the distribution is more uniform when the swirl number is 0.5. The fuel concentration in the center area of the center plane of side sector (Plane 5) is larger than that of the center plane of middle sector (Plane 1). The spray cone angle in Plane 5 is larger than that in Plane 1. The width of spray cone becomes larger with the increase of Fuel–Air Ratio (FAR), whereas the spray cone angle under different fuel–air ratios are absolutely the same. The results of the mechanism of spray organization in this study can be used to support the design of new low-emission combustor.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

突加不平衡下GTF发动机转子系统瞬态响应分析

针对GTF发动机低压转子系统突加不平衡瞬态响应问题,基于有限元法建立了考虑啮合单元、行星架单元、膜盘联轴器单元的多体接触、多转子耦合动力学模型,介绍了考虑非线性因素下突加不平衡瞬态响应计算方法,求解了低压转子系统的突加不平衡瞬态响应,并分析了关键部件刚度对突加不平衡的影响规律。结果表明：当风扇转子发生突加不平衡时,各部件均表现为振动幅值突增,后迅速趋于稳定,低压涡轮转子发生明显拍振,突加不平衡载荷主要由行星架结构和第1.5支点刚性支承承担;行星架刚度主要影响风扇转子突加不平衡响应、第1.5支点和行星架处的外传力;膜盘联轴器刚度主要影响增压级突加不平衡响应、转子在突加不平衡之后稳定运转情况。     

倾转四旋翼飞行器垂直飞行状态气动特性

综合采用基于滑移网格技术的计算流体力学(CFD)方法与悬停状态气动干扰试验方法,对倾转四旋翼(QTR)飞行器垂直飞行状态的流场进行模拟与试验,研究飞行器垂直飞行状态气动特性以及部分参数对气动特性的影响.结果表明:倾转四旋翼飞行器在垂直飞行状态,前后旋翼之间干扰不明显,但旋翼与机翼的干扰明显;旋翼旋向对旋翼与机翼的干扰不...     

干摩擦阻尼对旋翼动稳定性的影响研究

为了提高旋翼动稳定性理论模型的分析精度,需要精确地确定旋翼系统的结构阻尼系数。为此建立了旋翼变距拉杆球头关节干摩擦的阻尼模型,计入了球头关节的离心力对干摩擦阻尼的影响,然后用模型旋翼试验数据对稳定性分析结果进行了验证。结果表明,采用文中建立的干摩擦阻尼模型,预估的旋翼摆振后退型模态阻尼与试验数据吻合。     

前飞速度和升力偏置量对共轴刚性旋翼气动特性影响分析

共轴刚性旋翼前飞状态的气动特性主要由工况环境中的来流速度、密度和桨叶的翼型配置、弦长分布和扭转分布等气动布局参数决定。气动布局参数的综合影响决定了共轴刚性旋翼的的升力偏置量。了解前飞速度和升力偏置量对前飞性能的影响规律有利于设计更适合于高速飞行的共轴刚性旋翼。因此,本文通过求解可压雷诺平均N-S(Reynolds-averaged Navier-Stokes,RANS)方程对4 m直径的由两副2片矩形桨叶旋翼构成的共轴刚性旋翼模型的前飞流场进行了数值模拟,获得了不同前进比下的气动力并对不同升力偏置量下的旋翼性能进行了对比。数值模拟结果表明,随前进比增大,桨叶展向拉力分布更加趋于合理,拉力中心向桨叶中段移动,可以充分给桨尖卸载;旋翼升力主要由前行侧桨叶提供,升力偏置量过大容易产生激波诱导失速,不利于高速前飞。     

涡轴发动机高速两支点转子不平衡识别

针对实际工作中的涡轴发动机不平衡量难以监控现状,提出了一种基于非线性支承参数的涡轴发动机高速两支点转子不平量识别方法。建立起转子动力学有限元模型,以支承位移响应工频信号有效值为目标,采用Pointer优化器开展不平衡量识别,通过反馈迭代识别油膜阻尼、刚度。以某真实发动机转子的不平衡量开展识别验证,识别结果符合实际转子不平衡量变化规律,该识别方法计算效率满足工程要求,为发动机整机振动响应仿真分析中的不平衡量施加提供输入条件。