针刺C/C复合材料拉伸强度及渐进失效数值预测

基于金相显微镜观测的针刺C/C复合材料细观结构,考虑材料内部纤维的真实分布,建立了针刺C/C复合材料单胞模型。采用Linde失效准则,考虑纤维渐进损伤对材料进行了刚度折减,通过引入周期性位移边界条件,对针刺C/C复合材料的拉伸破坏进行了有限元法（FEM）数值模拟,分析了单胞模型的渐进失效过程,并预测了材料的拉伸强度。开展了针刺C/C复合材料拉伸试验,采用扫描电子显微镜（SEM）观察了材料的断口形貌,数值预测结果与试验吻合良好。针刺C/C复合材料受拉伸载荷后发生准脆性断裂,拉伸应力-应变曲线呈双线性,0°无纬碳布发生纤维断裂和基体开裂破坏,90°无纬碳布出现横向基体劈裂,最终断裂发生在针刺纤维与面内无纬碳布交叉区域。     

Parachute dynamics and perturbation analysis of precision airdrop system

To analyze the parachute dynamics and stability characteristics of precision airdrop system,the fluid–structure interaction(FSI) dynamics coupling with the flight trajectory of a parachute–payload system is comprehensively predicted by numerical methods.The inflation behavior of a disk-gap-band parachute is specifically investigated using the arbitrary Lagrangian–Euler(ALE) penalty coupling method.With the available aerodynamic data obtained from the FSI simulation,a nine-degree-of-freedom(9DOF) dynamic model of a parachute–payload system is built and solved to simulate the descent trajectory of the multi-body dynamic system.Finally,a linear five-degree-of-freedom(5DOF) dynamic model is developed,the perturbation characteristics and the motion laws of the parachute and payload under a wind gust are analyzed by the linearization method and verified by a comparison with flight test data.The results of airdrop test demonstrate that our method can be further applied to the guidance and control of precision airdrop systems.     

Prediction of cutting forces in ball-end milling of 2.5D C/C composites

Machining of carbon/carbon (C/C) composite materials is difficult to carry out due to its high specific stiffness, brittleness, anisotropic, non-homogeneous and low thermal conductivity, which can result in tear, burr, poor surface quality and rapid wear of cutters. Accurate and fast pre-diction of cutting forces is important for milling C/C composite materials with high quality. This paper presents an alternative cutting force model involving the influences of the directions of fiber. Based on the calculated and experimental results, the cutting forces’ coefficients of 2.5D C/C com-posites are evaluated using multiple linear regression method. Verification experiment has been car-ried out through a group of orthogonal tests. Results indicate that the proposed model is reliable and can be used to predict the cutting forces in ball-end milling of 2.5D C/C composites.     

Streamwise-body-force-model for rapid simulation combining internal and external flow fields

A streamwise-body-force-model (SBFM) is developed and applied in the overall flow simulation for the distributed propulsion system, combining internal and external flow fields. In view of axial stage effects, fan or compressor effects could be simplified as body forces along the streamline. These body forces which are functions of local parameters could be added as source terms in Navier-Stokes equations to replace solid boundary conditions of blades and hubs. The val-idation of SBFM with uniform inlet and distortion inlet of compressors shows that pressure perfor-mance characteristics agree well with experimental data. A three-dimensional simulation of the integration configuration, via a blended wing body aircraft with a distributed propulsion system using the SBFM, has been completed. Lift coefficient and drag coefficient agree well with wind tun-nel test results. Results show that to reach the goal of rapid integrated simulation combining inter-nal and external flow fields, the computational fluid dynamics method based on SBFM is reasonable.     

A dimension reduced INS/VNS integrated navigation method for planetary rovers

Inertial navigation system/visual navigation system (INS/VNS) integrated navigation is a commonly used autonomous navigation method for planetary rovers. Since visual measurements are related to the previous and current state vectors (position and attitude) of planetary rovers, the performance of the Kalman filter (KF) will be challenged by the time-correlation problem. A state augmentation method, which augments the previous state value to the state vector, is commonly used when dealing with this problem. However, the augmenting of state dimensions will result in an increase in computation load. In this paper, a state dimension reduced INS/VNS integrated nav-igation method based on coordinates of feature points is presented that utilizes the information obtained through INS/VNS integrated navigation at a previous moment to overcome the time rel-evance problem and reduce the dimensions of the state vector. Equations of extended Kalman filter (EKF) are used to demonstrate the equivalence of calculated results between the proposed method and traditional state augmented methods. Results of simulation and experimentation indicate that this method has less computational load but similar accuracy when compared with traditional methods.     

含激波的湍流流动高精度大涡数值模拟方法

针对采用亚格子模型进行含激波的湍流流动模拟时会面临激波附近的精度损失问题,考虑从通过亚格子模型以及数值模拟方法两方面的改进来实现湍流流动大涡模拟的精度提高.大涡模拟采用了Yee及Sj(o)green (2009)提出的高阶低耗散方法.该方法采用自适应的流场探测器以控制计算中所需区域的数值耗散,并考虑对动力学模型采用在激波位置使用Sagaut和Germano(2005)提出的单边亚格子过滤器和(或)直接禁用亚格子项等方法加以改进.对于标准的马赫数1.5和3条件下的激波-湍流干扰问题,上述新方法相较于全区域采用亚格子模型的方法均表现出了相似的精度提升.同时实现的数值精度改进方案采用了Harten的亚单元分辨过程来定位和锐化激波,并在精确激波位置附近的网格点处采用了单边测试滤波.     

C/SiC复合材料反射镜研究进展

反射镜在空间光学系统中起着非常关键的作用,目前已发展到第四代C/SiC复合材料。C/SiC复合材料具有低密度、高模高强、结构设计灵活等优点,已成为非常重要的新型反射镜材料。本文对四代反射镜的特点进行了归纳和对比,对C/SiC复合材料反射镜的结构设计、几种常用的制备工艺进行了整理和总结,并对目前国内外的研究进展进行了综述。     

高空飞艇螺旋桨优化设计与气动性能车载试验

结合某高空飞艇螺旋桨的总体设计方案要求,完成螺旋桨的优化设计以及气动性能车载试验.采用叶素动量理论作为螺旋桨气动性能的计算方法,并通过风洞试验验证了该方法的可靠性.结合遗传算法对螺旋桨的弦长和扭转角进行了优化,使螺旋桨更加高效轻质,优化后螺旋桨设计点的气动效率增加了2.3%.建立螺旋桨车载试验测控系统,可以改变试验海拔高度和大气参数,得到优化设计螺旋桨不同工况的气动性能.试验结果表明,相同转速和来流条件下,海拔越高,螺旋桨的推力和扭矩越小.海拔为3-6km时,全尺寸高空飞艇螺旋桨计算推力和扭矩与试验结果的平均相对误差分别为2.8%和9.2%,两者基本吻合,从而验证了高空飞艇螺旋桨车载试验的准确性.      

轨/姿控发动机试验数据快速自动处理技术

轨/姿控发动机试验数据需即时提供,大量数据的快速自动处理技术未见报道。在简述了高空模拟试验特点、Pacific6000原理及数据文件结构后,分析了当前计算方法优缺点;在此基础上,将网络脚本语言的设计思想引入试验数据处理过程,提出了实现数据快速处理的数据流式算法,进而形成自动处理技术;基于此算法开发了工程应用软件,在实际试验中应用,取得了良好效果。该技术对类似计算和海量数据的快速处理具重要工程参考意义。     

New results and questions of lunar exploration from SELENE,Chang’E-1, Chandrayaan-1 and LRO/LCROSS

The moon has longstanding questions such as lunar environments, origin, formation and evolution, magnetization of crustal rocks, internal structure and possible life. The recent lunar missions, e.g., SELenological and ENgineering Explorer “KAGUYA” (SELENE), Chang’E-1, Chandrayaan-1, and Lunar Reconnaissance Orbiter/Lunar CRater Observation and Sensing Satellite (LRO/LCROSS), have provided new opportunities to explore and understand these issues. In this paper, we reviewed and presented the results and findings in the fields of lunar gravity, magnetic field, atmosphere, surface geomorphology and compositional variations, volcano, craters, internal structure, water and life science from new lunar exploration missions. In addition, the new objectives and scientific questions on lunar explorations in near future are presented and discussed.