裂纹转子非线性振动特征的谐波小波与分形识别

通过对谐波小波的分析研究,指出了谐波小波对振动信号局部频段分析的优良特性。采用谐波小波对裂纹转子的非线性振动信号在低频段进行了分析。理论分析与实验结果表明:对实际裂纹转子信号,经谐波小波的频段分析后,能够得到通常难以由理论分析与实验结果获得的非整数倍周期分叉的非线性特征频谱。计算了裂纹转子的分形维数,发现裂纹转子的振动信号比理论结果要复杂、可以用多重分形作为判断实际转子是否有裂纹的一个特征。提出了用谐波小波变换后的奇异谱来识别裂纹转子非整数倍周期分叉的非线性特征频谱的方法,并对实际转子信号进行分析,得到了明显的非整数倍周期分叉的奇异谱。      

C/C-Cu复合材料的烧蚀形貌和烧蚀机理

以PAN预氧化纤维整体毡为增强体,经碳化、等温CVI致密化后制备多孔的C/C复合材料预制体,利用气体压力浸渗法将Cu引入C/C预制体中制备C/C-Cu复合材料。采用氢氧(H2-O2)焰考核C/C-Cu复合材料的烧蚀性能,经扫描电镜和电子能谱对不同烧蚀区域的微观结构和成分进行分析,结果表明:预制体密度为0.96 g/cm3的C/C-Cu复合材料的线烧蚀率和质量烧蚀率分别为4.75μm/s、0.223 mg/s,烧蚀性能优良;其烧蚀表面具有不同的宏观形貌,在烧蚀中心区产生了明显的凹坑,主要烧蚀机制为C/C预制体的氧化和铜基体的机械冲刷;烧蚀过渡区聚集了大量的铜基体,其烧蚀机制为Cu的热氧化和机械冲刷;烧蚀边缘区材料表面变黑,主要因为C/C的氧化。为了提高C/C-Cu的烧蚀性能,需要发挥C/C预制体的"钉扎"作用,阻止Cu在高温下被气流冲刷而发生流动。     

两种低噪声放大器性能对地面接收系统影响的分析

针对进口和国产低噪声放大器（ＬＮＡ）的增益和噪声温度指标，就中科院遥感卫星地面站运行接收系统的主要系统性能指标即Ｇ／Ｔ值和误码率进行了理论分析和实际测量。结果表明，国产ＬＮＡ比进口ＬＮＡ的增益提高９．８ｄＢ，噪声温度降低４Ｋ，接收系统增益改善约０．２５ｄＢ／Ｋ，１０－７误码率对应的Ｅｂ／Ｎ０改善约０．７ｄＢ。     

突加不平衡下GTF发动机转子系统瞬态响应分析

针对GTF发动机低压转子系统突加不平衡瞬态响应问题,基于有限元法建立了考虑啮合单元、行星架单元、膜盘联轴器单元的多体接触、多转子耦合动力学模型,介绍了考虑非线性因素下突加不平衡瞬态响应计算方法,求解了低压转子系统的突加不平衡瞬态响应,并分析了关键部件刚度对突加不平衡的影响规律。结果表明：当风扇转子发生突加不平衡时,各部件均表现为振动幅值突增,后迅速趋于稳定,低压涡轮转子发生明显拍振,突加不平衡载荷主要由行星架结构和第1.5支点刚性支承承担;行星架刚度主要影响风扇转子突加不平衡响应、第1.5支点和行星架处的外传力;膜盘联轴器刚度主要影响增压级突加不平衡响应、转子在突加不平衡之后稳定运转情况。     

非晶合金转子铁心对再制造电机性能的影响

用铁基非晶合金转子铁心替换原电机中的硅钢转子铁心,基于有限元软件Ansoft分析了非晶转子铁心替换对电机性能的影响。与原电机相比,再制造电机的转矩提升了2.6%,效率提高了0.05%,齿槽转矩幅值大幅增加。采用定子斜槽削弱其齿槽转矩,当斜槽精确为一个齿距时,电机的齿槽转矩幅值为0.128 N·m,相比于未采用斜槽时的再制造电机减小了92.36%,相比于原电机减小了38.46%。     

直升机桨叶连续后缘襟翼设计与气动影响分析

在直升机旋翼减振应用中,连续后缘襟翼和常规分离式襟翼相比具有重量轻、结构紧凑、气流平稳等优点。选用压电纤维复合材料作为驱动材料,基于NACA23012翼型设计带有连续变形后缘襟翼的桨叶段,对襟翼及其驱动结构进行选材设计分析;采用流固耦合方法分析连续后缘襟翼对剖面翼型气动特性的影响。结果表明:连续后缘襟翼在直升机桨叶工作迎角、马赫数范围内可实现有效偏转,显著改变翼剖面气动升力和力矩,证明了连续后缘襟翼在旋翼减振控制中的潜在应用价值。     

Design and application of an Electric Tail Rotor Drive Control (ETRDC) for helicopters with performance tests

With the development of electric helicopters’ motor technology and the widespread use of electric drive rotors, more aircraft use electric rotors to provide thrust and directional control. For a helicopter tail rotor, the wake of the main rotor influences the tail rotor’s inflow and wake. In the procedure of controlling, crosswind will also cause changes to the tail disk load. This paper describes requirements and design principles of an electric motor drive and variable pitch tail rotor system. A particular spoke-type architecture of the motor is designed, and the performance of blades is analyzed by the CFD method. The demand for simplicity of moving parts and strict constraints on the weight of a helicopter makes the design of electrical and mechanical components challenging. Different solutions have been investigated to propose an effective alternative to the mechanical actuation system. A test platform is constructed which can collect the dynamic response of the thrust control. The enhancement of the response speed due to an individual motor speed control and variable-pitch system is validated.     

Validation on MERSI/FY-3A precipitable water vapor product

The precipitable water vapor is one of the most active gases in the atmosphere which strongly affects the climate. China's second-generation polar orbit meteorological satellite FY-3A equipped with a Medium Resolution Spectral Imager (MERSI) is able to detect atmospheric water vapor. In this paper, water vapor data from AERONET, radiosonde and MODIS were used to validate the accuracy of the MERSI water vapor product in the different seasons and climatic regions of East Asia. The results show that the values of MERSI water vapor product are relatively lower than that of the other instruments and its accuracy is generally lower. The mean bias (MB) was ?0.8 to ?12.7?mm, the root mean square error (RMSE) was 2.2–17.0?mm, and the mean absolute percentage error (MAPE) varied from 31.8% to 44.1%. On the spatial variation, the accuracy of MERSI water vapor product in a descending order was from North China, West China, Japan -Korea, East China, to South China, while the seasonal variation of accuracy was the best for winter, followed by spring, then in autumn and the lowest in summer. It was found that the errors of MERSI water vapor product was mainly due to the low accuracy of radiation calibration of the MERSI absorption channel, along with the inaccurate look-up table of apparent reflectance and water vapor within the water vapor retrieved algorithm. In addition, the surface reflectance, the mixed pixels of image cloud, the humidity and temperature of atmospheric vertical profile and the haze were also found to have affected the accuracy of MERSI water vapor product.     

基于UG、Workbench平台航空发动机多盘转子结构自动优化方法

目前对航空发动机转子优化设计多限于单盘优化,且优化需要借助人工调整再优化。基于航空发动机转子优化设计常用软件平台数据交流方便和减少人工调整的考虑,提出了基于UG、Workbench平台航空发动机多盘转子结构自动优化方法。首先基于UG平台,对多盘转子结构进行参数化几何造型,借助生成的标准化模板,便于减少建模工作量及对同类盘的优化。然后基于Workbench平台,借助脚本语言（APDL、Python）二次开发完成对多盘转子结构状态变量提取,及自动优化流程控制。算例结果表明,在满足几何、强度要求条件下,优化后多盘转子结构质量减少了33%,应力分布更为均匀,且验证该方法具有良好的稳定性及精度。      

当量油气比对内燃波转子燃烧特性的影响

为了研究当量油气比对内燃波转子燃烧特性的影响规律,采用控制变量法,保持内燃波转子转速、混气填充速度不变,通过调节燃料喷射体积流量改变混气的当量油气比。在不同的当量油气比下开展内燃波转子燃烧特性试验。试验结果表明:当量油气比对于内燃波转子燃烧过程影响很大,随着当量油气比的增加,内燃波转子获得的燃烧压力增益增大,在内燃波转子转速为900r/min、混气填充速度为6.741m/s、当量油气比为1.442时,6个工作循环内平均燃烧压力增益达到246.29％,火焰平均传播速度随当量油气比呈类似正态分布,在化学恰当比附近达到最大10.8m/s。当量油气比小于1时,两组工况下火焰锋面呈向下倾斜状传播,当量油气比大于1时,两组工况下火焰锋面呈向上倾斜状传播。