旋转机械轴系不对中故障的建模及其理论分析

轴系不对中是旋转机械常见的故障,通过对该故障建立理论模型,并采用 Ｒａｃｃａｔｉ传递矩阵法对之进行数值计算和理论分析,重点计算了角度不对中时的振动特性。为旋转机械的故障诊断提供理论参考。     

二氧化碳（CO2）气硬树脂砂用促硬剂的研究

本文介绍了一种对碱性甲阶酚醛树脂有促硬作用的盐,在树脂中加入强碱和该促硬剂后,形成了稳定液态粘结剂,吹ＣＯ２气体硬化后可得到较高的即时抗压强度和２４小时抗压终强度。     

基于频域分析的ROSAR成像算法

在现有的ROSAR(Synthetic Aperture Radar with Rotating antennas)成像算法中,基于斜距泰勒级数展开的算法存在方位向失配问题,时域相关卷积算法不能快速校正距离弯曲.频域ROSAR成像算法采用驻相点原理,直接对ROSAR回波信号进行二维频域变换,保留回波信号的频谱特征,进而构造相应的频域去耦函数和频域匹配函数,实现频域距离弯曲校正和目标场景重构.仿真结果表明,该算法能够快速校正距离弯曲及有效克服方位向失配问题.     

基于热管-风冷系统的新能源汽车电机热分析

针对新能源汽车电机紧凑、轻量化、高功率密度和高可靠性的要求,提出基于热管-风冷系统的新型冷却系统。设计了基于热管-风冷系统的电机结构,建立电机有限元热分析模型并验证其可行性;通过有限元模拟,研究该新型电机在额定功率和峰值功率下的温度场。结果表明:热管-风冷系统能有效地控制电机的温升。与水冷系统相比,无需水泵、节温器、水箱、管路以及其他装置,结构简单、紧凑,有利于实现新能源汽车的轻量化和高功率密度。     

基于旋转高频信号注入法的内置式永磁同步电机低速段转子位置检测及其误差补偿

旋转高频信号注入法注入信号较为稳定,且位置估计过程不依赖电机参数,因而十分适用于内置式永磁同步电机(IPMSM)的零、低速转子位置检测。针对传统高频信号注入法无法辨别磁极的问题,用电压方波注入法检测磁极,结合有限元软件仿真,来合理选取方波电压幅值和时长,有效缩短了磁极判断耗时。分析了滤波器和信号离散化对位置估计精度的影响,提出在低速段可用线段拟合带通滤波器中心频率处的相频特性曲线,推导所需补偿角度与电机转速的关系。在理论分析的基础上,采用基于DSP28335的样机平台进行试验,结果表明磁极判断过程稳定,耗时较短,补偿后的位置估计值相比补偿前有明显改善,调速过程中系统动态性能良好。     

射流管伺服阀前置级压力特性

为分析射流管伺服阀射流管喷嘴高压射流区的特性,建立了射流管伺服阀前置级数学模型,得到了射流管偏移值、射流管喷嘴半径和接收孔半径对接收器压力分布、喷嘴出口流速及接收器的左右孔恢复压力的影响规律.流场分析发现射流管喷嘴的高速射流出口处容易产生旋涡,且存在环状负压效应.结果表明:高压射流状态下,射流管喷嘴半径增大,恢复压力增加;接收孔半径增大,恢复压力降低.接收孔半径与射流管喷嘴半径之比的最佳取值区间为[1.3,1.5].当射流管偏移值增大时,在偏移值增大一侧,射流管与接收孔之间的有效流体接收面积增大,射流管与接收孔之间的流体旋涡扩大,内部流场环状负压效应增加,接收孔恢复压力降低.      

低雷诺数下离心压气机性能及流动影响的数值研究

对高空低雷诺数条件下低压离心压气机进行了全三维数值模拟,分析了雷诺数对其内部流场的影响.结果表明:随着雷诺数降低,离心压气机的效率、裕度和流通能力下降;影响叶片表面负荷分布,使得转子叶片的做功能力下降;叶片前缘分离区范围增大,二次流增强,分流叶片叶尖泄漏损失增大,主叶片吸力面通道的低速区明显增大,起始位置也向前移动,对展向的影响区域也随之增加.      

Flow Stability Model for Fan/Compressors with Annular Duct and Novel Casing Treatment

A three-dimensional compressible flow stability model is presented in this paper, which focuses on stall inception of multi-stage axial flow compressors with a finite large radius annular duct configuration for the first time. It is shown that under some assumptions, the stability equation can be obtained yielding from a group of homogeneous equations. The stability can be judged by the non-dimensional imaginary part of the resultant complex frequency eigenvalue. Further more, based on the analysis of the unsteady phenomenon caused by casing treatment, the function of casing treatment has been modeled by a wall impedance condition which is included in the stability model through the eigenvalues and the corresponding eigenfunctions of the system. Finally, some experimental investigation and two numerical evaluation cases are conducted to validate this model and emphasis is placed on numerically studying the sensitivity of the setup of different boundary conditions on the stall inception of axial flow fan/compressors. A novel casing treatment which consists of a backchamber and a perforated plate is suggested, and it is noted that the open area ratio of the casing treatment is less than 10%, and is far smaller than conventional casing treatment with open area ratio of over 50%, which could result in stall margin improvement without obvious efficiency loss of fan/compressors.     

A Dual-driven Intelligent Combination Control of Heat Pipe Space Cooling System

Effective thermal control systems are essential for reliable operation of spacecraft.A dual-driven intelligent combination control strategy is proposed to improve the temperate control and heat flux tracking effects.Both temperature regulation and heat flux tracking errors are employed to generate the final control action;their contributions are adaptively adjusted by a fuzzy fusing policy of control actions.To evaluate the control effects,describe a four-nodal mathematical model for analyzing the dynamic characteristics of the controlled heat pipe space cooling system(HP-SCS) consisting of an aluminum-ammonia heat pipe and a variable-emittance micro-electromechanical-system(MEMS) radiator.This dynamical model calculates the mass flow-rate and condensing pressure of the heat pipe working fluid directly from the systemic nodal temperatures,therefore,it is more suitable for control engineering applications.The closed-loop transient performances of four different control schemes have been numerically investigated.The results conclude that the proposed intelligent combination control scheme not only improves the thermal control effects but also benefits the safe operation of HP-SCS.     

旋转激光陀螺惯导系统误差传播特性分析

设计旋转式惯导系统(INS, Inertial Navigation System)最重要的工作是理清旋转调制误差自动补偿机理、掌握补偿前后误差的传播特性,在此基础上设计合理的转位方案,并对其进行仿真和试验验证.结合单轴旋转式惯导系统工作原理和误差传播方程,解释了旋转调制误差自动补偿的机理,利用理论和仿真两种手段分析了单轴旋转惯导系统中惯性元件常值误差、随机误差、标度因数误差和安装误差的传播特性,得到了旋转调制对惯性器件误差的调制效果,验证了单轴正反转停方案的有效性和应用的合理性.研究结果为旋转式激光陀螺(LG, Laser Gyroscope)惯导系统的设计提供了理论参考和设计依据.