Motion synchronization in a dual redundant HA/EHA system by using a hybrid integrated intelligent control design

This paper presents an integrated fuzzy controller design approach to synchronize a dis-similar redundant actuation system of a hydraulic actuator (HA) and an electro-hydrostatic actu-ator (EHA) with system uncertainties and disturbances. The motion synchronous control system consists of a trajectory generator, an individual position controller for each actuator, and a fuzzy force tracking controller (FFTC) for both actuators. The trajectory generator provides the desired motion dynamics and designing parameters of the trajectory which are taken according to the dynamic characteristics of the EHA. The position controller consists of a feed-forward controller and a fuzzy position tracking controller (FPTC) and acts as a decoupled controller, improving posi-tion tracking performance with the help of the feed-forward controller and the FPTC. The FFTC acts as a coupled controller and takes into account the inherent coupling effect. The simulation results show that the proposed controller not only eliminates initial force fighting by synchronizing the two actuators, but also improves disturbance rejection performance.     

飞机数字化装配系统中机身交点孔加工方法研究

针对传统交点孔加工方法加工精度低且存在回弹变形的问题,设计了一种满足飞机大部件数字化装配要求的机身交点孔精加工方法,根据交点孔的加工特性完成了机身定位与固持、数控加工中心定位以及加工工艺的总体设计,确定了交点孔加工程序原点的计算方法和编程原则,最后通过交点孔试切加工试验验证了加工方法的可行性。     

Multi-level virtual prototyping of electromechanical actuation system for more electric aircraft

Electromechanical actuators (EMAs) are becoming increasingly attractive in the field of more electric aircraft because of their outstanding benefits, which include reduced fuel burn and maintenance cost, enhanced system flexibility, and improved management of fault detection and isolation. However, electromechanical actuation raises specific issues when being used for safety-critical aerospace applications like flight controls: huge reflected inertia to load, jamming-type failure, and increase of backlash with service due to wear and local dissipation of heat losses for thermal balance. This study proposes an incremental approach for virtual prototyping of EMAs. It is driven by a model-based system engineering process in order to enable simulation-aided design. Best practices supported by Bond graph formalism are suggested to develop a model’s structure efficiently and to make the model ready for use (or extension) by addressing the above mentioned issues. Physical effects are progressively introduced, and the realism of lumped-parameter models is increased step-by-step. In particular, multi-level component models are architected to ensure continuity between engineering activities. The models are implemented in the AMESim simulation environment, and simulation responses are given to illustrate how they can be used for preliminary sizing, control design, thermal balance verification, and faults to failure analysis. The proposed best practices intend to provide engineers with fast, reusable, and efficient means to assess performance virtually and enhance maturity, performance, and robustness.     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.     

Experimental study on plasma jet deflection and energy extraction with MHD control

This paper presents an integrated research scheme for vector deflection and energy extraction in a gas plasma jet under Magneto-Hydrodynamic (MHD) control. A MHD-controlled thrust-vector test rig was used to conduct the experimental research. A gas plasma was obtained by injecting ionization seeds of Cs₂CO₃ into the combustion chamber via artificially forced ionization. The effects of the gas temperature and ionization seed mass fraction on the plasma jet deflection and energy extraction were experimentally verified under an applied magnetic field. The experimental results were analyzed theoretically. The results showed that the deflection amplitude of the gas plasma jet and the extracted voltage signal intensity increased with increasing gas temperature and the ionization seed mass fraction. The extracted dynamic voltage signals proved that the ionization seeds of Cs₂CO₃ induced gas ionization at 1173 K. The experiment verified that it is feasible to simultaneously achieve jet deflection and extract energy under the action of an external magnetic field.     

低速大转矩永磁游标电机在发酵罐中的应用

采用秸秆生产丁醇时,为了达到高效率发酵,需要使发酵液中菌体分布均匀,所加物料需要及时搅拌。工业化生产丁醇的发酵罐尺寸较大,搅拌过程对驱动电机的输出转矩要求较高,因此高效率、小体积、低速大转矩的秸秆发酵搅拌电机对工业化发酵生产丁醇意义重大。设计了一种定转子永磁游标电机用于发酵液搅拌,并对电机的槽极数、电磁性能进行了具体的研究。制造样机并采用滞环控制实现了对液态发酵对象的快速响应,且实现了低能耗、高效率的发酵过程。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

助推-滑行式燃料最优真空飞行轨迹的设计方法

建立了飞行器助推-滑行式燃料最优真空飞行轨迹的最优控制模型,给出了一种更为简单、直观的内点约束条件和横截条件的推导方法,讨论了高效且更为稳定的数值计算方法,提出了两种应用模式,通过与连续推力式和脉冲式飞行方案的比较,说明这种设计方法在节省燃料方面具有优势.     

阵风载荷减缓系统故障分析

阵风引起的额外载荷会引起飞机结构疲劳,降低结构使用寿命。采用非定常气动力有理函数拟合方法建立时域状态空间下的动力学系统,设计了阵风载荷减缓系统。研究了阵风载荷减缓系统3种典型故障模式(副翼偏转饱和、舵机卡死、副翼偏转延时)的力学建模方法,并对机翼在阵风减缓系统故障模式下的阵风响应进行分析。仿真结果表明,3种故障模式均不利于阵风载荷减缓系统对阵风载荷的减缓,对于一些特定情况,故障模式下的阵风载荷减缓系统不仅不能减缓阵风载荷,还会带来由副翼偏转不当引起的额外负载。