基于动网格技术的飞机舱弹分离过程 CFD/ RBD耦合数值仿真

飞机舱弹分离瞬间特性严重影响导弹/炸弹的打击精度。采用计算流体动力学(CFD)和刚体动力学(RBD)模型耦合求解的数值仿真方法,应用网格弹性光顺和局部重构相结合的动网格技术,有效地避免了刚体运动而引起的网格畸变,仿真计算了炸弹舱弹分离后俯仰角度变化过程 .仿真结果表明,舱弹分离时向炸弹施加 1个合适的抛 射力矩,有助于炸弹在下降过程中快速地调整其打击姿态。     

Environmental stress level evaluation approach based on physical model and interval grey association degree

 Associating environmental stresses (ESs) with built-in test (BIT) output is an important means to help diagnose intermittent faults (IFs). Aiming at low efficiency in association of traditional time stress measurement device (TSMD), an association model is built. Thereafter, a novel approach is given to evaluate the integrated environmental stress (IES) level. Firstly, the selection principle and approach of main environmental stresses (MESs) and key characteristic parameters (KCPs) are presented based on fault mode, mechanism, and ESs analysis (FMMEA). Secondly, reference stress events (RSEs) are constructed by dividing IES into three stress levels according to its impact on faults; and then the association model between integrated environmental stress event (IESE) and BIT output is built. Thirdly, an interval grey association approach to evaluate IES level is proposed due to the interval number of IES value. Consequently, the association output can be obtained as well. Finally, a case study is presented to demonstrate the proposed approach. Results show the proposed model and approach are effective and feasible. This approach can be used to guide ESs measure, record, and association. It is well suited for on-line assistant diagnosis of faults, especially IFs.     

数值研究低热值燃料环管燃烧室燃烧流场

在任意曲线坐标系下对采用两种不同组分(天然气掺混氮气、一氧化碳)的低热值燃料环管燃烧室燃烧流场进行计算,结果表明低热值燃料的化学反应速率与其组分直接有关,燃料一氧化碳的燃烧效率高于天然气与氮气掺混物燃料,燃料组分变化对燃烧室燃烧效率与出口温度影响很大,因此选用合适的燃料十分重要.计算所得的燃烧室的燃烧效率和出口温度分布与试验数据符合较好,表明所用的数学模型与计算方法合理,计算程序可靠,可为低热值气体燃料燃烧室研制和优化设计提供有用的数据.      

水下超声速过膨胀燃气射流的流场特性

为研究水下超声速过膨胀燃气射流的流场特性,在压力水筒中开展了大扩张比锥形喷管的固体火箭发动机水下点火实验,并基于雷诺时均Navier-Stokes（RANS）方法和流体体积（VOF）模型进行数值求解,分析了过膨胀燃气射流与水介质的相互作用过程。研究表明：超声速过膨胀燃气建立射流通道后,射流核心区长度随喷管落压比的减少而减少;射流核心区剧烈振荡,表现为高频的膨胀和收缩,振荡频率随喷管落压比的减小而增加,范围为100~200 Hz;射流边界不断振荡,并伴随波系结构变化,当过膨胀程度较大时,激波进入喷管使其发生流动分离现象,流动分离点周期性往复移动;分离区内压力脉动没有显著的特征频率,主要集中在100~600 Hz的宽频带,锥形喷管水下流动分离的简易判据为喷管出口压力不低于环境背压的0.44倍。     

SAR performance-based fault diagnosis for electro-hydraulic control system: A novel FDI framework for closed-loop system

Model-based fault diagnosis serves as an efficient and powerful technique in addressing fault detection and isolation (FDI) issues for control systems. However, the standard methods and their modifications still encounter some difficulties in algorithm design and application for complex higher-order systems. To avoid these difficulties, a novel fault diagnosis framework based on multiple performance indicators of closed-loop control system is proposed. Under this framework, a so-called performance residual vector is constructed to measure the differences between the real system and the nominal model in terms of system stability, accuracy, and rapidity (SAR) respectively. The criteria for quantification, normalization of the SAR residuals and the explicit mappings between the thresholds and the required performance are given. FDI can be easily achieved simultaneously by monitoring the normalized residual vector length and direction in the SAR performance residual space. A case study on electro-hydraulic servo control system of turbofan engine is adopted to demonstrate the effectiveness of the proposed method.     

某型飞机尾喷管开裂原因分析

尾喷管作为飞机发动机的重要组成部件之一,主要由薄板焊接而成。由于其长期在高温、振动以及气流冲刷等恶劣环境中工作,常出现尾喷管失效事故,而焊缝作为尾喷管中的薄弱部分,常出现开裂现象。某型飞机尾喷管在飞行完成后的例行检查中在焊缝上以及焊缝周边检查发现两处裂纹。通过宏观检验、断裂面形貌分析以及金相组织分析等方法对其开裂原因进行了分析。结果表明:由于结构设计原因,尾喷管上同一位置存在多次焊接现象,为多密集焊缝结构件,使得焊接接头过热,焊缝组织中铁素体呈现网状分布,同时尾喷管母材上存在焊接烧穿现象,导致焊接接头力学性能下降,使得疲劳裂纹萌生并扩展;支撑螺杆与加强筋未焊满,收弧处为点连接而非面连接,在飞行过程中,该位置发生振动应力集中并萌生疲劳裂纹,并最终发生疲劳失效。     

蓄热式太阳能热光伏-热推进双模系统换热特性数值模拟研究

本文通过三维数值模拟研究蓄热式太阳能热光伏-热推进双模系统的蓄/释热特性和推进性能。在蓄热式太阳能热推进系统工程模型的基础上,通过射线光学的光路分析验证了聚光器设计的合理性,并获得吸热腔壁面能量分布情况,进一步研究了相变蓄热过程的影响因素。基于场协同原理对热光伏再生冷却结构进行了优化设计,使热光伏具有较好的散热特性,提高发电功率;通过整机流动换热仿真,分析了工质流体在推进器内部的换热情况,计算结果表明,蓄热式热推进器具有达到734s比冲和0.9N推力的推进性能,以及能够满足日蚀区微小卫星的供电和推力需求。     

风洞分布式支撑天平测力试验技术研究

采用双尾支撑测量形式的加工、装配误差会使系统内应力过大,影响测量精度。针对某“双机身”飞机CTS 风洞试验气动力测量需求,发展基于多维力天平内置的风洞分布式支撑天平测力试验技术;研制具有消除系统内应力功能的双支撑系统,提出两种6 分量双支撑天平校准及测力方法,并对数据处理和双支撑系统可靠性进行检验加载、对比分析和验证。结果表明：风洞分布式支撑天平测力试验技术能够有效消除双支撑天平系统由于过约束而导致的固有装配内应力,双支撑天平系统各部分连接、测量可靠;两种校准测力方法测量精度相当,均能达到单台应变天平测量误差水平,可满足风洞试验测量精度需求;综合考虑现有校准设备校准能力,最终采用“合成式校准测力”方法进行的风洞试验,获得了满意的试验测力精度。     

不同压比状态下超声速射流冲击斜板的声场/流场特性

为研究超声速射流冲击斜板的噪声特性及声源特性,针对不同压比下,超声速射流流场及声场分别进行了高频PIV(particle image velocimetry)测量与远场噪声测量.PIV测量结果可观测到激波格栅形成过程以及冲击斜板对它的影响.声场测量结果可捕捉到自由射流与冲击射流中不同的纯音频率随压比增加的转变过程.通过...     

水下重力辅助惯性导航关键技术研究及实现

重力辅助惯性导航已渐成水下导航领域的研究热点,其实现是一项复杂的工程,涉及多项的关键技术.文章首先介绍了重力辅助导航的基本原理;之后详细阐述了在真实海洋环境下,重力辅助导航所需解决的若干关键技术问题,并给出了相应的研究成果;最后总结了我国水下重力辅助导航的发展趋势及研究的若干建议.