吸力面附面层抽吸在三维高负荷扩压叶栅中的作用机制

对某矩形高负荷扩压叶栅在不同弦向位置开设全叶高抽吸槽的5组方案进行了数值研究,分析了抽吸槽弦向位置等参数对抽吸量分布规律的影响;通过叶栅实验探究了局部展向抽吸方案的效果.数值仿真的计算域包含吸附叶片内部的真空腔,边界条件按照实验条件设置.研究发现:全叶高抽吸方案的抽吸量沿展向大致呈C型分布;叶高中部和端部的主要抽吸效果都体现在叶高中部流场,端部的抽吸量对叶栅角区的回流有一定的抑制效果.抽吸量沿展向的分布规律受叶栅流道和叶片内腔流场的共同作用,因此应根据三维高负荷扩压叶栅流场的具体特性对吸力面抽吸槽/孔进行细化设计.      

射线追踪法在球面收敛调节片喷管RCS计算中的应用

结合射线追踪法的原理,利用自主开发的电磁散射特性计算程序,对具有不同尾缘修型的球面收敛调节片喷管进行了数值模拟计算,分别得到了不同喷管内部腔体散射场和喷管出口边缘绕射场的雷达散射截面积(RCS),并且通过计算获得了不同入射方位角上喷管腔体内壁面上的感应电流,通过对感应电流的分析,从本质上解释了RCS的变化规律.研究结果表明:对喷管出口尾缘所采用的修型措施在降低喷管出口边缘绕射场的RCS和改善喷管电磁隐身性能方面效果显著;相对于普通的遮挡算法,射线追踪法将计算周期缩短了21%以上,明显地提高了计算效率;利用感应电流的分析方法能够清晰直观地从本质上解释RCS的变化规律,并且具有较高的可靠性.      

高超声速飞行器后体/尾喷管优化设计

结合试验设计方法、替代模型技术和遗传算法构建一套改进的优化方法,并将其应用于高超声速飞行器后体/尾喷管的一体化设计.在构建优化方法时,针对替代模型采用渐近全局策略提高精度;针对遗传算法,采用实数编码、多目标定级排序和改进小生境技术.在后体/尾喷管的一体化设计应用中,结合高精度的计算流体力学(CFD,Computational Fluid Dynamics)求解,以两个设计点的推力和升力为目标,以力矩为约束,得到优化问题的Pareto最优前沿面,优化结果在综合性能方面有很大提升.该优化方法可进一步推广应用于更复杂的优化设计当中.      

声能喷嘴供油级间驻涡燃烧室的性能试验

对一种采用声能喷嘴供油方式的级间燃烧室进行了性能试验研究.试验结果表明:当进口马赫数为0.20~0.40,燃烧室的熄火余气系数为25~35,燃烧室的稳定工作范围较宽;随余气系数增大,出口温度分布均匀性提高;燃烧效率为96%~98%,随余气系数减小,燃烧效率降低;进口马赫数对点火性能、熄火性能、出口温度分布和燃烧效率的影响较小;壁面热点温度出现在凹腔的后壁面;总压损失系数为0.03~0.11,热态时比冷态时高0.015左右; CO和NOx的排放指数分别为20~46和0.9~2.1,进口马赫数、余气系数均对污染物排放有较大影响.      

Influence of fuel injection position and equivalent mixture ratio on chemical non-equilibrium effects of single expansion ramp nozzle

Chemical non-equilibrium flow was investigated for the scramjet single expansion ramp nozzle(SERN) with a strut-based liquid-kerosene-fueled combustor.Two-dimensional Reynolds-averaged Navier-Stokes(RANS) equations were solved with the species conservation equation for continuous phase and the renormalization group(RNG) k-ε turbulence model.Lagrangian discrete-phase model was analyzed for liquid-kerosene droplets behavior in the supersonic stream.Combustion was simulated by kerosene surrogate fuel's 10-species and 13-step reduced reaction kinetics mechanism with use of Arrhenius's laminar finite rate model.Parametric studies were carried out to estimate the influence of different fuel injection positions and equivalent mixture ratios on the SERN chemical non-equilibrium effects.Numerical calculation results show that the strut-based combustor enables convenient modeling of various SERN entry conditions,which is similar with many preceding investigations,by changing the injector strut position and controlling the mass flow rate of each injector.Chemical non-equilibrium effects function in the whole SERN,especially in the initial flow expansion region,leads to obviously higher SERN performance of the non-equilibrium flow than that of the frozen flow.Furthermore,the distributed fuel injection pattern plays a significant role in enhancing the combustion efficiency in combustor,but weakening the chemical non-equilibrium effects funciton in SERN.Additionally,while the equivalent mixture ratio increases,the SERN thrust coefficient and lift coefficient rise gradually,and the increment of non-equilibrium flow in relation to frozen flow becomes higher as well.To be specific,the equivalent mixture ratio is 0.6,the maximum increment of thrust coefficient and lift coefficient are 11.6% and 25% respectively.      

高超声速等截面磁流体发电机性能研究

采用三维低磁雷诺数磁流体动力学五方程模型,对等截面管道法拉第型分段电极磁流体发电机内的流动进行数值模拟,研究了负载系数、磁场强度、电极-绝缘壁宽度比对发电通道性能的影响.结果表明:当负载系数为0.50时电功率密度达到最大,并且随着负载系数的增大发生器的减速能力降低;当磁场强度为8T时,500mm的管道长度即可将来流马赫数从6降低到3以下,温度保持在800K以下,并且每立方米的管道发电量能够达到兆瓦级的水平.      

流体控制矢量喷管启动过程的瞬态响应

采用三维非定常数值模拟方法对流体矢量喷管启动的瞬态响应过程进行了研究,给出了流场的演化特性及性能参数的响应时间.根据不同时刻的流场和壁面压力分布,分析后得到了注气附近射流扰动波系及漩涡的演化过程,并与上壁面压力分布相互印证.由性能参数(包括流量,推力系数,矢量角)的时间响应曲线发现:流量和推力系数在响应初始阶段存在剧烈波动,而矢量角是平稳变化,三者的响应时间在毫秒量级.      

某型直升机发动机尾喷管前转接段模态分析

某型直升机发动机出现的尾喷管裂纹故障主要发生在尾喷管前转接段焊缝周围。为分析故障原因,文章建立了该型发动机尾喷管结构的计算模型。对该型喷管整体结构进行了自由振动和模态分析,获得了该喷管模型的多阶自振频率和模态。将有限元分析结果和实验结果对比表明,两者所得的固有频率吻合性较好。     

Numerical investigation of of nozzle cavities thermal radiation characteristics with center cone cooled

航空发动机高温部件是发动机3-5μm上的重要红外辐射之一,对高温部件之一的中心锥的红外抑制技术进行了数值研究．在中心锥前端布置气膜缝槽,缝槽几何参数经过优化设计,将部分外涵低温气流经过支板引入中心锥,对支板和锥体壁面形成冲击冷却,在锥体前端形成气膜覆盖,使得支板与中心锥壁面得到了有效冷却,两者平均温度分别降低21．1％和46．2％,冷却气量约为外涵流量的1．6％．喷管腔体3～5Izm波段上红外辐射得到有效抑制,喷管正后方红外辐射相比原型喷管降低30％,0°-45。范围内红外辐射则明显降低．     

Experimental Investigation of Nozzle Effects on Thrust and Inlet Pressure of an Air-breathing Pulse Detonation Engine

Nozzle effects on thrust and inlet pressure of a multi-cycle air-breathing pulse detonation engine (APDE) are investigated experimentally. An APDE with 68 mm in diameter and 2 050 mm in length is operated using gasoline/air mixture. Straight nozzle, converging nozzle, converging-diverging nozzle and diverging nozzle are tested. The results show that thrust augmentation of converging-diverging nozzle, diverging nozzle or straight nozzle is better than that of converging nozzle on the whole. Thrust augmentation of straight nozzle is worse than those of converging-diverging nozzle and diverging nozzle. Thrust augmentations of diverging nozzle with larger expansion ratio and converging-diverging nozzle with larger throat area range from 20% to 40% on tested frequencies and are better than those of congeneric other nozzles respectively. Nozzle effects on inlet pressure are also researched. At each frequency it is indicated that filling pressures and average peak pressures of inlet with diverging nozzle and converging-diverging nozzle with large throat cross section area are higher than those with straight nozzle and converging nozzle. Pressures near thrust wall increase in an increase order from without nozzle, with diverging nozzle, straight nozzle and converging-diverging nozzle to converging nozzle.