飞机装配工装组件库与快速装配设计技术

结合航空企业数字化应用的现状,基于飞机装配工装设计中的应用需求,研究工装组件的参数化设计、参数化组件库的构建以及组件的快速装配设计技术。应用CAA在CATIA平台上进行二次开发,实现了飞机装配工装组件库和快速装配设计功能,可提高装配工装设计的效率和质量。     

月球卫星的自主轨道确定

分别利用紫外三轴姿态敏感器测出的月心方向和测距仪测出的月心距作为观测量,采用推广卡尔曼滤波方法实时确定出月球卫星环月期间的轨道,考虑到月球卫星在环月期间太阳对月球光照条件的限制,提出分段虑波策略,并给出了仿真分析.     

“嫦娥3号”月面探测器同波束干涉测量系统的设计与实现

为了提高"嫦娥3号"探测器(着陆器和巡视器)的相对定位精度,针对两器信标实际设置情况,设计了同波束干涉测量(same-beam interferometry,SBI)观测方案。利用着陆器和巡视器星地对接数据分析检验了由差分群时延解算含微小系统差的差分相时延的方法,给出了甚长基线干涉测量(very long baseline interferometry,VLBI)和同波束干涉测量模型及月面定位方法,并仿真分析了巡视器的相对定位精度。最终,把研究的方法实际应用于"嫦娥3号"巡视器的精密相对定位。结果表明,利用1h左右的连续观测弧段的着陆器数传信号以及巡视器数传信号(或遥测信号),采用事后处理方式,得到了随机误差约1ps的差分相时延数据。利用此数据,把"嫦娥3号"探测器的相对定位精度提高至1m左右。     

Time-varying solar radiation pressure on Ajisai in comparison with LAGEOS satellites

This study aims to investigate solar radiation pressure acting on the spherical geodetic satellites, Ajisai, LAGEOS-1, and LAGEOS-2. The solar radiation pressure coefficients ($C_R$) are derived in two independent ways: (a) through precise orbit determination (POD) using satellite laser ranging (SLR) data, and (b) through modeling using the optical properties of the satellite surface material. The average $C_R$ value of Ajisai (1.039), as calculated from the time series of $C_R$ POD estimates every 15?days, is consistently smaller than those of LAGEOS-1 (1.140) and LAGEOS-2 (1.103). This difference can be explained by the fact that the surface of Ajisai is mostly covered by mirrors. The Ajisai $C_R$ values estimated by POD show remarkable semi-annual variation, which disagrees with the results of a previous study (Sengoku et al., 1995) predicting that the $C_R$ of Ajisai varies almost annually. We attribute this semi-annual variation to two physical reasons: the non-spherical additional cross-sectional area due to the “attached fitting ring” and the low reflectivity of the surface material in the polar regions. Furthermore, the solar radiation pressure acting on Ajisai varies annually in a direction perpendicular to the sun-satellite vector. Finally, the two independent $C_R$ values of Ajisai agree more when we assume a total solar irradiance of 1361?W/m², whereas the value 1367?W/m² has been commonly used in POD.     

LEO enhanced Global Navigation Satellite System (LeGNSS) for real-time precise positioning services

Global Navigation Satellite System (GNSS) has been widely used in many geosciences areas with its Positioning, Navigation and Timing (PNT) service. However, GNSS still has its own bottleneck, such as the long initialization period of Precise Point Positioning (PPP) without dense reference network. Recently, the concept of PNTRC (Positioning, Navigation, Timing, Remote sensing and Communication) has been put forward, where Low Earth Orbit (LEO) satellite constellations are recruited to fulfill diverse missions. In navigation aspect, a number of selected LEO satellites can be equipped with a transmitter to transmit similar navigation signals to ground users, so that they can serve as GNSS satellites but with much faster geometric change to enhance GNSS capability, which is named as LEO constellation enhanced GNSS (LeGNSS). As a result, the initialization time of PPP is expected to be shortened to the level of a few minutes or even seconds depending on the number of the LEO satellites involved. In this article, we simulate all the relevant data from June 8th to 14th, 2014 and investigate the feasibility of LeGNSS with the concentration on the key issues in the whole data processing for providing real-time PPP service based on a system configuration with fourteen satellites of BeiDou Navigation Satellite System (BDS), twenty-four satellites of the Global Positioning System (GPS), and sixty-six satellites of the Iridium satellite constellations. At the server-end, Precise Orbit Determination (POD) and Precise Clock Estimation (PCE) with various operational modes are investigated using simulated observations. It is found out that GNSS POD with partial LEO satellites is the most practical mode of LeGNSS operation. At the user-end, the Geometry Dilution Of Precision (GDOP) and Signal-In-Space Ranging Error (SISRE) are calculated and assessed for different positioning schemes in order to demonstrate the performance of LeGNSS. Centimeter level SISRE can be achieved for LeGNSS.     

星载SAR亚马逊雨林辐射定标仿真研究

辐射定标是准确、定量描述星载合成孔径雷达(SAR)系统性能的重要手段.星载SAR在轨运行期间,天线方向图较之发射前可能存在较大的失真,从而严重影响所获取的SAR图像数据质量,因此准确测量在轨飞行时天线俯仰向方向图特性并予以补偿是星载SAR辐射定标的主要内容之一.利用具有均匀后向散射系数特性的分布目标进行外定标是测量双程俯仰向天线方向图的最佳方案,而亚马逊雨林是全球最稳定、最均匀、最平坦的分布目标,后向散射系数几乎不随入射角变化,是公认的理想测试场地.鉴于目前我国尚无自行采集的星载SAR图像数据,我们对星载SAR回波功率仿真、天线方向图模型参数估算进行了深入、系统的研究,利用仿真的亚马逊雨林SAR功率图像成功地实现了星载SAR俯仰向天线方向图在轨测试关键环节的模拟,对我国的星载SAR辐射定标研究具有一定的理论意义和重要的工程实用价值.      

一种高动态条件下惯性星光组合定姿方法

针对高动态条件下星图拖尾导致惯性星光组合定姿精度下降甚至无法定姿的问题,提出了一种基于乘性扩展卡尔曼滤波的惯性星光深度组合姿态确定方法.利用星敏感器观测信息修正姿态误差,补偿陀螺漂移,并建立了陀螺输出的角度变化量与星图像移的关系,利用陀螺输出信息估计星图拖尾的模糊参数,采用维纳滤波复原方法对产生拖尾的星图进行复原以提高星图信噪比和观测精度.仿真结果表明该方法可以有效提高星像质心提取精度和星图识别率,对初始姿态误差修正更快,且不存在星图误匹配的情况,保证了惯性星光组合定姿方法在高动态条件下仍能保持较高的精度.     

低轨卫星对高轨卫星仅测角初轨计算方法

针对我国地面测站对高轨卫星监视能力缺乏的问题,提出一种低轨卫星对高轨卫星仅测角初轨计算方法。该算法引入天基跟踪坐标系,消除测距信息影响,建立仅测角观测方程;引入法向运动,增加摄动因素影响,建立扩展拉普拉斯动力学模型;推导分析观测模型和动力学模型的关系方程,将初轨计算问题转换为非线性方程求解问题,利用高斯全主元消去法完成方程求解。通过实战和仿真测角数据对方法进行检验,结果表明,该方法能利用仅测角数据对非合作目标进行初轨确定,精度在公里量级,可为我国地基监视系统提供补充参考。     

多敏感器联邦SSUKF融合姿态确定算法

针对四元数姿态估计问题,提出了一种分布式非线性滤波融合结构。通过引入基于超球面分布采样点变换(SSUT)技术的无迹卡尔曼滤波算法(SSUKF),以较低的计算量实现了高数据更新率、高精度的非线性滤波,并通过融合重构,保障系统无间断可靠工作,不受敏感器故障、视场盲区等因素影响。应用该算法对陀螺、磁强计、太阳敏感器、星敏感器构成的系统进行了具体设计并开展仿真研究,验证了算法的有效性。     

单星导航HEO卫星初轨确定算法

HEO(Highly Elliptical Orbit)轨道卫星利用星载GPS(Global Positioning System)进行自主定轨面临的主要难题之一就是解决在单颗导航卫星条件下的初轨确定问题.从理论上分析了利用单颗导航卫星的观测量确定HEO卫星轨道初值的所需满足的条件,指出了利用F.G级数法求解初值存在的问题,提出了一种基于轨道根数约束的迭代批处理算法,该算法无需复杂的数学运算,避免了F.G级数法用短弧资料定初轨时系数矩阵秩亏的影响.仿真结果表明,当先验轨道根数误差在允许范围内取值时,在考虑轨道射入误差的情况下,初值的位置偏差在10⁴ m量级,速度偏差在10⁰ m/s量级,能够根据单颗导航卫星的短弧观测值可靠地完成轨道初值的确定.