An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.     

基于功能危险性评估的民用飞机驾驶舱门设计探讨

FAA分别于2002年和2008年颁布25-106及25-127修正案,增加驾驶舱门安保事项以提高驾驶舱的安全水平。修正案要求加固驾驶舱门,驾驶舱门必须设计成可以阻止未被授权人员进入驾驶舱并且阻碍危险物体射入以保证机组人员的安全。驾驶舱门必须能检测驾驶舱失压并可以释放门或者卸压板平衡压力差,还应有措施使飞机机组成员在该舱门卡住的情况下能直接从驾驶舱进入客舱。因此,在驾驶舱门上设有一个可以快速释放的紧急出口。根据飞机驾驶舱门结构及功能的主要特点,对驾驶舱门功能故障进行探讨,同时对功能故障引发的危险性等级进行划分,以确定安全指标,进而辅助驾驶舱门设计工作。     

发动机动力模拟风洞试验中的空气桥技术

介绍了发动机动力模拟风洞试验中的空气桥设计技术和影响修正方法.通过自由度分析,选择了合理空气桥布局,采用有限元方法对空气桥关键受力梁进行了优化,建立了空气桥天平一体化数值模拟技术,使得空气桥和天平刚度更加匹配.通过这些设计及优化使得空气桥的作用力最小,并具有较强的克服压力影响、温度影响的能力.通过试验建立了空气桥附加刚度影响、内部压力影响、温度影响和内部流量影响的修正方法,进一步减小了空气桥对天平的影响.在8m×6m低速风洞进行了某大展弦比飞机全模涡扇动力模拟器(TPS)短舱动力模拟试验.试验结果重复性好,阻力系数精度达到0.0003,和相关文献吻合.这表明空气桥技术是成功的,满足了TPS短舱动力模拟试验要求.      

某3级风扇试验流场诊断及性能优化

压气机试验是检验压气机设计是否达标的重要过程,并可在原设计基础上进行优化来发掘设计的潜能。利用级间总压和壁面静压在某3级风扇第1阶段试验对级间流场进行了详细测量和级性能诊断,提出了静叶角度优化方案;通过第2阶段试验,得出了角度优化后使设计转速喘振裕度提高了7.5个百分点,达到了设计指标的结论。流场诊断技术在压气机试验中起到了关键作用。结果表明:壁面静压结合级间径向总压测量方法基本能够满足在压气机试验中性能优化的需要。     

RT-11燃油调节器加速性不稳定原因分析

介绍了某型发动机的RT-11燃油调节器加速性不稳定、起飞状态燃油供油量停滞的情况,分析了产生故障的原因和故障机理,并提出了修理中的改进措施。     

机载燃油惰化技术及标准研究

针对目前广泛应用于飞机燃油箱起火和爆炸防护的机载燃油惰化系统,详述了国外机载燃油惰化技术的发展历程,并介绍了国内发展现状,提出影响机载燃油惰化系统设计的关键因素。在此基础上,简述了国内外标准情况,提出了制定我国机载燃油惰化系统标准的建议。     

超声速串列静叶积叠优化分析

在进口超声速、气流转折角大的高负荷条件下,静叶通道中激波强度高,激波、附面层干扰引起的损失大,且静叶中三维流动引起的径向载荷分布不均匀,易产生角区分离。叶片积叠优化是提高风扇性能的一项有效技术。采用数值模拟的方式研究了不同积叠形式对优化串列静叶沿展向激波结构,改善叶排间流动匹配的作用。三维流动对比分析可以得出:高负荷串列静叶采用正弓形积叠,叶片展向载荷分布合理,静叶端壁角区分离损失减小,前后叶片排流动匹配较好,风扇性能进一步提高。     

浅谈基于IPDT的民用飞机重量控制技术

在民机研制过程中,有效地实施重量控制对于项目的成功非常关键。飞机超重不仅会导致设计和运营成本的增加,也将无法实现既定的商载和航程等设计指标。从各部门与重量控制工作的联系出发,结合某型民用飞机的设计实践,介绍了产品联合研发团队(IPDT)模式下重量控制的工作内容、工作流程和常用的减重方法,为民机的重量控制工作提供借鉴和参考。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.