Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

基于ALE法的水陆两栖飞机船体着水性能分析

水陆两栖飞机的着水性能是体现其综合性能的重要因素之一.应用ALE法对三种水陆两栖飞机船体截面进行入水仿真计算,从着水载荷、喷溅性能及运动响应三个方面对着水性能进行综合评估.对比分析了直线型、带舭弯弧形、复合型三种构型截面在不同速度、不同重量下的压力分布、喷溅性能以及运动响应,得到了三种截面横向压力分布规律.计算结果显示相同状态下,喷溅性能复合型优于带舭弯弧形、带舭弯弧形优于直线型;过载复合型远大于带舭弯弧形,带舭弯弧形稍大于直线型,综合看来带舭弯弧形截面着水性能最佳.     

动力失效对起飞纵向气动特性影响数值研究

研究民用飞机动力失效对飞机起飞阶段纵向气动特性的影响规律及其机理,对保证飞机有效操纵和安全飞行具有重要意义.采用在点对点多块结构化网格系统上求解三维可压缩雷诺平均N-S方程的数值方法,研究发动机动力失效对某民用飞机起飞构型纵向气动特性的影响.通过DLR-F11模型验证研究方法对民用飞机高升力构型气动特性的预测能力;针对安装动力短舱的某翼吊涡扇发动机民用飞机起飞构型,通过对比其发动机在正常工况和失效时飞机气动特性的差异,得出动力失效对飞机纵向气动特性的影响规律及机理.结果表明:动力失效后,不但溢流效应会使飞机阻力系数增大;还会导致发动机进、排气特性较正常工作状态明显不同,恶化短舱附近流场,对飞机的升力、失速特性带来不利影响.     

基于测控系统的质量信息监测系统设计与应用

在测控试验现场,针对测控设备状态和测控数据的质量信息,采用智能自动监测技术对设备和测控数据进行实时监视以及动态分析,提出了科学的异常判决方法和处理方案,开发了试验质量信息综合分析实时监测系统,实现了测控流程智能化管控、测控信息自动分析处理和质量信息自动化管理。在多颗卫星的跟踪验证中,质量信息监测系统对卫星长期管理的宏参数宏配置下发、标校和目标捕获与跟踪等任务过程能够进行准确监视,可以及时监测到测控数据和测控时间的异常并报警,并能够自动生成任务实施登记表等测控质量报表。实验表明,质量信息监测系统软硬件设计完善、状态监测点设置合理、判读测控事件方法有效。     

典型工况下低排放燃烧室的压力振荡特性

为了研究低排放燃烧室在典型工况下的压力振荡特性,针对模型燃烧室进行了燃烧自激振荡特性试验.在试验中测量了采用贫油预混预蒸发(LPP)燃烧技术的低排放燃烧室在典型工况下的压力振荡频率和幅值,在燃烧室进口压力为1.10～2.77MPa、燃烧室进口温度为656～845 K、燃烧室压降为3.41％～4.35％范围内,分析了燃油粒径变化对振荡特性的影响.分析结果表明:局部当量比脉动是引发燃烧不稳定的因素之一.通过计算燃油二次雾化状态下的液滴最大粒径,发现燃油液滴粒径的变化对主燃级出口处的局部当量比脉动有直接影响,从而引起燃烧室压力振荡幅值和频率的变化.     

零件表面微观工艺特征性研究 ——产品(零件)工艺技术基础科学问题机理探索

通过研究产品(零件)制造过程、方法、参数等工艺因素,给零件表面及表层带来(留下)特有的微观特征性,首次在高精度惯性仪表和高可靠电磁继电器(机电类)产品制造体系中引入了零件表面微观工艺特征性概念,提出了制造阶段的产品工艺可靠性设计和微观工艺特征(性)分析方法,提出了该类产品制造中的工艺设计更应该关注零件与产品设计原理匹配性和性能特性符合性观点,提出零件制造要从单纯的控制几何精度向控制性能特性转变,从宏观、单一采标的几何参数评价向微观、综合采标的非几何(非尺寸)参数评价模式为主转变的建议.零件表面存在的这种微观特征现象与零件几何精度一样,将对产品制造的合格率、稳定性、可靠性的实现起到至关重要的作用,尤其对产品的合格率影响极大,有必要开展更深入、更系统的研究,以建立起我国自主的高端产品(或零件)制造基准工艺平台.     

不同进口截面下液力透平非定常压力脉动计算

为了研究不同进口截面对液力透平内压力脉动的影响,利用CFX软件对一单级液力透平进行非定常数值计算,通过设置监测点,计算各监测点在不同进口截面下的压力脉动,通过快速傅里叶变换将其压力脉动计算结果做相应分析,分析各监测点处压力脉动的时域和频域分布.结果表明:蜗壳内在大蜗壳进口下,随着蜗壳进口直径的增加,每个监测点处的压力逐渐增加,而在小蜗壳进口下,每个监测点处的压力逐渐减小.在距离蜗壳收缩管较远处,大蜗壳进口下的压力脉动较小,而在距离收缩管较近处,小蜗壳进口下的压力脉动较小.在叶轮内不同进口截面压力脉动的差异在同一时刻从进口到出口逐渐减小.尾水管内在小蜗壳进口下尾水管进口处的压力脉动最大.      

负游隙对高速高温薄壁圆柱滚子轴承动态性能的影响分析

计算了圆柱滚子轴承径向游隙为负值时的等效径向预紧载荷,并考虑等效径向预紧载荷下的套圈弹性变形,通过求解包含套圈弹性变形接触变形等效径向预紧载荷的非线性方程组,得到负游隙圆柱滚子轴承内部的载荷分布情况,以及负径向游隙带来的套圈周向应力.以此分析了负游隙对轴承承载性能及疲劳寿命的影响.结果表明:负径向游隙能够有效降低轴承打滑率,但同时也会降低轴承疲劳寿命,因此在负游隙设计时需同时考虑打滑率和轴承寿命,选择恰当的负游隙.     

Advances and trends in plastic forming technologies for welded tubes

With the implementation of environmental protection, sustainable development and conservation-oriented policies, components and parts of thin-walled welded tubes have gained increasing application in the aircraft and automotive industries because of their advantages: easily achieving forming and manufacturing process at low cost and in a short time. The current research on welded tube plastic forming is mainly concentrated on tube internal high-pressure forming, tube bending forming, and tube spinning forming. The focuses are on the material properties and characterization of welded tubes, finite element modeling for welded tube forming, and inhomogeneous deformation behavior and the mechanism and rules of deformation coordination in welded tube plastic forming. This paper summarizes the research progress in welded tube plastic forming from these aspects. Finally, with a focus on the urgent demand of the aviation, aerospace and automotive industries for high-strength and light-weight tubes, this paper discusses the development trends and challenges in the theory and technology of welded tube plastic forming in the future. Among them,laser tailor-welded technology will find application in the manufacture of high-strength steel tubes.Tube-end forming technology, such as tube flaring and flanging technology, will expand its application in welded tubes. Therefore, future studies will focus on the FE modeling regarding how to consider effects of welding on residual stresses, welding distortions and microstructure, the inhomogeneous deformation and coordination mechanism of the plastic forming process of tailor-welded tubes, and some end-forming processes of welded tubes, and more comprehensive research on the forming mechanism and limit of welded tubes.     

导风轮叶片偏置对高压比串列离心压气机性能的影响

为提升高压比串列离心压气机的性能,借鉴常规一体化离心叶轮中偏置分流叶片的方法,针对某高压比串列离心压气机,应用数值仿真手段分析了串列叶轮中导风轮叶片周向偏置对压气机流场和性能的影响。通过对不同导风轮叶片偏置方案下压气机流场的分析,建立了压气机流动损失与偏置参数的关联性。研究表明:采用较大的偏置参数γ可降低导风轮叶片1前缘的激波强度,改善激波作用导致的泄漏涡破碎和流动分离,但过大或过小的γ方案中导风轮叶顶会出现二次泄漏致使低能流体的掺混损失增加;γ=65%方案压气机综合性能最佳,其压比和效率较γ=50%分别提高了1.5%和1.4%;对于串列离心压气机导风轮叶片周向位置的优化,在避免导风轮叶顶形成较强二次泄漏的前提下,应考虑采用较大的偏置参数γ,同时应防止诱导轮尾迹流体参与导风轮的叶顶泄漏。